13.230 防爆 标准查询与下载

GB 16543-2008 高炉喷吹烟煤系统防爆安全规程

本标准规定了炼铁厂高炉喷吹烟煤系统中煤粉爆炸预防与防护措施的基本要求。 本标准适用于炼铁厂高炉喷吹烟煤以及烟煤与无烟煤混合喷吹系统的新建、扩建和改造工程项目的设计、施工与验收，以及操作、维护、检修及管理。无烟煤喷吹系统可参照执行。

Safety regulations for explosion prevention and protection on bituminous coal injection system into blast furnace

GB 15577-2007 粉尘防爆安全规程

本标准规定了粉尘爆炸危险场所的防爆安全要求。 本标准适用于粉尘爆炸危险场所的工程设计、生产管理及粉末产品的贮存和运输。 本标准不适用于矿山、烟花爆竹和火炸药粉尘场所。

Safety regulations for dust explosion prevention and protection

GB 18245-2000 烟草加工系统 粉尘防爆安全规程

本标准规定了烟草加工系统粉尘防爆的基本要求。 本标准适用于烟草加工系统粉尘防爆的设计、施工、运行和管理。

Safety regulation for dust explosion in tobacco processing system

GB/T 18154-2000 监控式抑爆装置技术要求

本标准规定了监控式抑爆装置的技术要求、试验方法、检验规则与标志、包装和贮存。 本标准适用于工业生产流程中抑制可燃粉尘燃烧与爆炸的各种型式的监控式抑爆装置的设计与制造。

Technical specification of automatic dust explosion suppression devices

GB/T 17919-1999 粉尘爆炸危险场所用收尘器 防爆导则

本标准规定了粉尘爆炸危险场所用收尘器的防爆要求。 本标准适用于粉尘爆炸危险场所用收尘器的设计、安装及维护检修。 本标准不适用于矿山井下。

Directives for dust explosion protection for dust collectors in dust explosion hadardous ares

GB 17918-1999 港口散粮装卸系统粉尘防爆安全规程

本标准规定了港口散粮装卸系统粉尘防爆的基本要求。 本标准适用于港口散粮装卸系统粉尘防爆的设计、施工、运行和管理。

Safety regulation for dust explosion protection in raw grain loading and unloading system in port

GB 17440-1998 粮食加工、储运系统粉尘防爆安全规程

本标准规定了粮食加工、储运系统爆炸性粉尘环境危险区域划分及范围、对加工工艺设备、电气、建筑结构、通风、除尘、积尘清扫、气力输送及管理的粉尘防爆安全要求。 本标准适用于粮食装卸、运输、储藏和加工过程中出现或可能出现粮食粉尘爆炸性危险环境的新建、扩建工程的设计、施工，粮食生产、储运和管理的全过程。 本标准适用于粮食加工、储运系统，不适用于浸出油车间。

Safety regulations for the protection of dust explosion for grain processing, storage and transportation system

GB 16543-1996 高炉喷吹烟煤系统防爆安全规程

本标准规定了炼铁厂高炉喷吹烟煤系统中煤粉爆炸的预防与防护的基本要求。 本标准适用于炼铁厂高炉喷吹烟煤以及烟煤与无烟煤混合喷吹系统的新建、扩建和改造工程项目的设计、施工与验收，以及操作、维护、检修及管理。无烟煤喷吹系统可参照执行。

Safety regulations for the explosion precautions of bituminous coal injection into blast furnace

GB/T 15605-1995 粉尘爆炸泄压指南

本标准对设计和应用围包体中粉尘爆炸泄压技术和装置，作了指导性规定。 本标准适用于围包体粉尘爆燃的泄压。 本标准不适用于粉尘爆轰，也不适用于由于外部火焰或暴露于其他火源中而产生过大内压的围包体泄压。 本标准不适用于有毒物质和有腐蚀性粉尘及火、炸药粉尘。 本标准不适用于为防护失控放热过程的安全阀。 本标准不适用于如绝缘油变压器这种设备的泄压或民用压力罐。

Guide for venting of dust explosions

GB/T 15604-1995 粉尘防爆术语

本标准规定了粉尘防爆的专业术语。 本标准适用于粉尘防爆标准的制定、技术文件的编制、专业手册及教材书刊编写和翻译。 本标准不适用于炸药粉尘。

Terminology for dust explosion prevention

T/IFP 500-2024 可燃性粉尘除尘系统防爆设计指南

目前，我国可燃/涉爆粉尘行业企业用的除尘系统防爆设计多遵循 GB 15577《粉尘防爆安全规程》纲领性文件，各企业在行业及粉尘种类等约束条件下进行具体的规范设计；工贸行业企业的可燃性粉尘用除尘系统对安全生产影响较大，特别是因其设计没有具体规范要求，后续施工、验收环节乱象丛生，导致事故的发生频繁，安全生产形势十分严峻。 国内目前没有专门针对可燃性粉尘除尘系统防爆设计的标准规范，本标准的制定将从除尘系统的防爆设计出发，减少可燃性粉尘用除尘系统因设计不当/不到位等情况造成返工改造的冗余工作，降低可燃性粉尘除尘系统防爆改造的成本和安全事故发生几率，提高全民安全生产责任意识。 本标准在制订过程中，借鉴和参考了国外一些先进标准的要求，但主要强制性条文还是结合国情、根据国标制订的基本原则而制订。本标准在制订过程中，参考了 NFPA 652、NFPA 654、NFPA 484、NFPA 91、VDI 2263 等国外最新标准，并采纳了这些标准中的部分技术内，同时根据中国国情进行了适当的修改，技术水平为跟踪国际水平。

Guidelines for Explosion Prevention and Protection Design of Combustible Dust Collection Systems

T/QGCML 3132-2024 气动油桶倒料车智能防爆监测装置

本文件规定了气动油桶倒料车智能防爆监测装置的术语和定义、构成及原理、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于气动油桶倒料车智能防爆监测装置的生产及检验。

Intelligent explosion-proof monitoring device for pneumatic oil drum dumping truck

DB50/T 867.52-2023 安全生产技术规范 第52部分：烟花爆竹零售店（点）

本文件适用于烟花爆竹零售店（点）的设置和安全管理。

Technical Specifications for Production Safety Part 52: Fireworks and Firecrackers Retail Stores (Point)

DB50/T 867.53-2023 安全生产技术规范 第53部分：烟花爆竹经营（批发）企业

本文件适用于企业的安全生产。

Technical Specifications for Production Safety Part 53: Fireworks and Firecrackers Business (Wholesale) Enterprises

T/ZSRA 001-2023 排爆机器人通用技术要求

本文件规定了排爆机器人的术语和定义、分类、技术要求、试验方法、标志和说明等内容。

General technical requirements of explosive disposal robots

ASTM E2021-15(2023) 灰尘层热表面着火温度的标准试验方法

1.1 This test method covers a laboratory procedure to determine the hot-surface ignition temperature of dust layers, that is, measuring the minimum temperature at which a dust layer will self-heat. The test consists of a dust layer heated on a hot plate.2,3 1.2 Data obtained from this test method provide a relative measure of the hot-surface ignition temperature of a dust layer. 1.3 This test method should be used to measure and describe the properties of materials in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire hazard risk of materials, products, or assemblies under actual fire conditions. However, results of this test method may be used as elements of a fire risk assessment that takes into account all of the factors that are pertinent to an assessment of the fire hazard risk of a particular end use product. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Hot-Surface Ignition Temperature of Dust Layers

T/ZZB 2910-2022 火花探测和水基熄灭系统

本文件规定了火花探测和水基熄灭系统的基本要求、 系统组成和使用环境、 技术要求、试验方法、检验规则、 说明书、 标识、包装、运输、 储存和质量承诺。 本文件适用于在除尘风管、气力输送管道等可燃粉尘输送管道中探测火花并采用喷水方式熄灭火花的安全防护系统（以下简称“系统”）。 本文件不适用于除尘系统、气力输送系统的火灾监控和消防喷淋系统。

Spark detecting and water based extinguishing systems

DB44/T 2390-2022 粉尘涉爆企业安全风险防控技术规范

本文件适用于广东省内粉尘涉爆企业开展安全风险辨识、分析、分级与防控工作的实施和管理。 本文件不适用于危险化学品、烟花爆竹、火炸药企业以及涉强氧化剂的粉尘场所。

Technical specifications for safety risk prevention and control of dust explosion-related enterprises

BS EN 17624:2022 高压、高温或空气以外的氧化剂下气体和蒸气爆炸极限的测定

This document specifies a test method to determine the explosion limits of gases, vapours and their mixtures, mixed with a gaseous oxidizer or an oxidizer/inert gas mixture at pressures from 0,10 MPa to

Determination of explosion limits of gases and vapours at elevated pressures, elevated temperatures or with oxidizers other than air

ASTM E1515-14(2022) 可燃粉尘最小爆炸浓度的标准试验方法

1.1 This test method covers the determination of the minimum concentration of a dust-air mixture that will propagate a deflagration in a near-spherical closed vessel of 20 L or greater volume. NOTE 1—The minimum explosible concentration (MEC) is also referred to as the lower explosibility limit (LEL) or lean flammability limit (LFL). 1.2 Data obtained from this test method provide a relative measure of the deflagration characteristics of dust clouds. 1.3 This test method should be used to measure and describe the properties of materials in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment that takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Minimum Explosible Concentration of Combustible Dusts