共找到 972 条与 相关的标准,共 65 页
Design documents for special equipment for electronic industry.Part 1:Completeness of design documents
Design documents for special equipment for electronic industry.Part 2:Title blocks,addition list and item list of drawing
Design documents for special equipment for electronic industry.Part 3:Format of design documents
Design documents for special equipment for electronic industry.Part 4:Drafting of design documents
本标准规定了电子工业专用设备的要求,试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于电子工业专用设备的设计、制造和验收。本行业各类设备应根据本标准的原则编制相应的产品标准。
General specification for special equipment for electronic industry
本标准规定了精密丝网印刷机的定义、要求、试验方法、检验规则、标志包装运输贮存等。 本标准适用于电子元器件高精度图文印刷的丝印机。其他类型的丝印机也可参照使用。
General specification for precision sereen printer
本标准规定了塑料注射模模架的10种基本组合形式及组合规格尺寸表等内容。 本标准适用于注射量为10kg以下注射机(含10kg注射机)用的、其周界尺寸为130mm×130mm~125mm×160mm的各种模具。
Mould bases of injection mould for plastic
Design procedure guide of reliability for electronic equipment
本标准规定了电子行业在建立设备管理标准时,制订设备完好标准应遵循的原则和完好设备的基本要求。 本标准适用于电子行业国有企业、事业单位,其他企、事业单位亦可参照执行。
General rules for equipment readiness
本标准规定子半导体器件生产用离子束蚀刻机的完好要求和检查、评定方法。 本标准适用于电子产品生产、科研用离子束蚀刻机。
Requirements of readiness and methods of inspection and assessment for ion beam etching machines
本标准规定了塑料注射模模板的结构尺寸、标记示例及技术要求。 本标准适用于塑料注射模各种模架和定模板、动模板、定模座板,动模座板。
Components of injection mould for plastics.Mould plates
本标准规定了塑料注射模模架组合的技术要求、验收规则、包装、运输和贮存等内容。 本标准适用于塑料注射模模架组合的技术条件。
Specification for mould bases of injection mould for plastic
Components of injection mould for plastics.Spacer
本标准规定了塑料注射模模架的组合规格、结构型式代号、组合代号及模架组合的标记示例等内容。 本标准适用于塑料注射模各种型式模架组合的编号规则。
Numbering system for mould bases of injection mould for plastic
本标准规定了塑封模具预热装置结构形式、基本尺寸、应用方式。 本标准适用于SJ/T 10515.6 塑封模具结构 预定位架规定的塑封模具。
Configuration of plastic packaged mould.Pre-heating unit
Components of injection mould for plastics.Ejector retainer or plate
本标准规定了塑封模具注塑结构形式、基本尺寸、应用方式。 本标准适用于SJ/T 10515.1 塑封模具结构 典型结构规定的塑封模具。
Configuration of plastic packaged mould.Guide configuration
本标准规定了塑封模具导向结构形式、基本尺寸、应用方式。 本标准适用于SJ/T 10515.1塑封模具结构 典型结构规定的塑封模具。
Configuration of Plastic packaged mould.Locating configuration
本标准规定了塑封模具型腔结构形式,基本尺寸、应用方式。 本标准适用于SJ/T10515.1塑封模具结构 典型结构规定的塑封模具。
Configuration of plastic packaged mould.Injection configuration
本标准规定了塑封模具定位、结构形式、基本尺寸、应用方式。 本标准适用于SJ/T 10515.1塑封模具结构 典型结构规定的塑封模具。
Configuration of plastic packaged mould.Cavity configuration
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号