31.020 电子元器件综合 标准查询与下载

IEC 61760-2:2007 表面安装技术.第2部分:表面安装器件(SMD)的运输和存储条件.使用指南

This International Standard describes the transportation and storage conditions for surface mounting devices (SMDs) that are fulfilled in order to enable trouble-free processing of surface mounting devices, both active and passive. (Conditions for printed boards are not taken into consideration.) The object of this standard is to ensure that users of SMDs receive and store products that can be further processed (e.g. positioned, soldered) without prejudice to quality and reliability. Improper transportation and storage of SMDs may cause deterioration and result in assembly problems such as poor solderability, delamination and "popcorning".

Surface mounting technology - Part 2: Transportation and storage conditions of surface mounting devices (SMD) - Application guide

IPC TM-650 2.5.5.13-2007 使用分体式气缸谐振器的相对介电常数和损失正切

This specification covers the requirements for base materials, herein referred to as laminate or prepreg, to be used primarily for rigid or multilayer printed boards for electrical and electronic circuits.

Relative Permittivity and Loss Tangent Using a Split-Cylinder Resonator

CEA-CEB18-2007 便携式电子装置控制发射和位状指示信号的推荐规程(T-PEDs) (彩色)

This document describes the portion of the Power Line or RF Physical Layer that interfaces to the Medium Access Control (MAC) Sublayer and to Layer System Management (LSM). This sublayer is called the Power Line/RF Symbol Encoding (PL/RF SE) Sublayer. The PL/RF SE Sublayer provides two primary functions:

Recommended Practice for Transmitter Control and Status Indication in Transmitting Portable Electronic Devices (T-PEDs) (Contains Color)

CEA-909-A-2007 天线控制接口

The properties of the Logical Units’ user interfaces originating from a physical device are available using the GET IPaddr/2027_file command, where the IPaddr is the IP address of the physical device in dotted decimal notation in ASCII. Service devices shall return an XML document, see [6], describing all device supported Logical Units as the concatenation of all Logical Unit block descriptions. The schemas for the 2027 file and opcodes in Annex B are informative.

Antenna Control Interface

KS A IEC 61709:2006 电子部件.可靠性.变换的故障率及应力模型的基准条件

이 규격은 전자장비에 사용되는 부품의 신뢰성 예측을 위해 고장률 데이터 사용에 관한 지침을

Electronic components－Reliability－Reference conditions for failure rates and stress models for conversion

KS A IEC 61709-2006(2017) 电子元器件可靠性故障率和转换应力模型的参考条件

Electronic components－Reliability－Reference conditions for failure rates and stress models for conversion

KS A IEC 61709-2006(2022) 电子元件－可靠性－故障率和转换应力模型的参考条件

Electronic components－Reliability－Reference conditions for failure rates and stress models for conversion

AIMC 0002-2006 无源射频标签通用技术规范

本标准规定了无源射频标签的通用技术要求和测试方法。 参照ISO/IEC18000-n系统标准，包括：低于135kHz（ISO/IEC 18000-2），13.56MHz（ISO/IEC 18000-3，ISO 15693，ISO 14443）2.45GHz（ISO/IEC 18000-4），860MHz～960MHz（ISO/IEC 18000-6）,433MHz（ISO/IEC 18000-7）。 对标签应用环境条件特殊的，可能要求采取减缓措施。

General technical specifications for passive tag

DIN CLC/TS 50466:2006 电子元件的长期存储.实施规则

This document, which is in line with IEC/PAS 62435 relating to the management of obsolescence of electronic components, is first of all a practical guide to methods of long duration storage (more than 5 years) which summarizes the existing practices in the industry

Long duration storage of electronic components - Specification for implementation; German version CLC/TS 50466:2006

IEC 60938-2:1999+AMD1:2006 CSV 抑制电磁干扰用固定电感器第2部分:分规范

Fixed inductors for electromagnetic interference suppression - Part 2: Sectional specification

IEC 60938-1:1999+AMD1:2006 CSV 抑制电磁干扰用固定电感器.第1部分:总规范

Fixed inductors for electromagnetic interference suppression - Part 1: Generic specification

SN/T 2003.5-2006 电子电气产品中铅、汞、铬、镉和溴的测定 第5部分：能量色散X射线荧光光谱定量筛选法

Determination of lead,mercury,chromium,cadmium and bromine in electrical and electronic equipment-Part 5:Quantitative screening by energy dispersive X-ray fluorescence spectrometric method

SJ/T 11364-2006 电子信息产品污染控制标识要求

本标准规定了电子信息产品中有毒有害物质或元素的名称和含量、环保使用期限、可否回收利用及包装材料名称的标识要求。 本标准适用于在中华人民共和国境内销售的电子信息产品。

Marking for control of pollution caused by electronic information products

SJ/T 11365-2006 电子信息产品中有毒有害物质的检测方法

本标准规定了电子信息产品中有的铅(Pb)、汞(Hg)、镉(Cd)、六价铬[Cr(Ⅵ)]、多溴联苯(PBB)和多溴二苯醚(PBDE)六种限用的有毒有害物质或元素的检测方法。 本标准适用于《管理办法》定义的电子信息产品。

Testing methods for hazardous substances in electronic information products

SJ/T 11363-2006 电子信息产品中有毒有害物质的限量要求

本标准规定了电子信息产品中有毒有害物质的最大允许浓度。 本标准适用于《电子信息产品污染控制管理办法》中规定的进入污染控制重点管理目录的电子信息产品。

Requirements for concentration limits for certain hazardous substances in electronic infromation products

DS/EN 61760-1:2006 表面贴装技术 第1部分：表面贴装元件（SMD）规范的标准方法

This Standard gives a reference set of process conditions and related test conditions to be used when compiling component specifications of electronic components that are intended for usage in surface mount technology.

Surface mounting technology – Part 1: Standard method for the specification of surface mounting components (SMDs)

DS/CLC/TS 50466:2006 电子元件的长期储存 实施规范

Although it has always existed to some extent, obsolescence of electronic components, and particularly integrated circuits, has become increasingly intense over the last few years. Indeed, with the existing technological boom, the commercial life of a component has become very short compared with the life of industrial equipment such as those encountered in the aeronautical field, the railway industry or the energy sector. The many solutions enabling obsolescence to be resolved are now identified. However, selecting one of these solutions must be preceded by a case by case technical and economic feasibility study, depending on whether storage is envisaged f

Long duration storage of electronic components - Specification for implementation

SJ 51425/2-2006 BFU32- IC 型波导假负载详细规范

本规范规定了BFU32- IC 型波导假负载（以下简称假负载）的详细要求。 本规范适用于BFU32- IC 型波导假负载。

Dummy load, electrical, waveguide, type BFU32- IC detail specification for

SJ 51425/1-2006 BFU84- IC 型波导假负载详细规范

本规范规定了BFU84- IC 型波导假负载（以下简称假负载）的详细要求。 本规范适用于BFU84- IC 型波导假负载。

Dummy load, electrical, waveguide, type BFU84- IC detail specification for

CEA TECHNICAL PAPER-2006 家庭网络的无线技术评估：一期报告中,以满足消费者的应用需求的比较技术性能特点

The properties of the Logical Units’ user interfaces originating from a physical device are available using the GET IPaddr/2027_file command, where the IPaddr is the IP address of the physical device in dotted decimal notation in ASCII. Service devices shall return an XML document, see [6], describing all device supported Logical Units as the concatenation of all Logical Unit block descriptions. The schemas for the 2027 file and opcodes in Annex B are informative.

Home Network Wireless Technologies Evaluation: Phase I Report Comparison of Technology Performance characteristics to Consumer Application Needs