77.180 冶金设备 标准查询与下载
共找到 437 条与 冶金设备 相关的标准，共 30 页
Safety of machinery - Safety requirements to finishing lines for metal strip
- ICS
- 77.180
- CCS
- 发布
- 2021-09-00
- 实施
Safety of machinery - Safety requirements for hot flat rolling mills
- ICS
- 77.180
- CCS
- 发布
- 2021-09-00
- 实施
Tensile straightening machine used in continuous hot dip galvanizing line
- ICS
- 77.180
- CCS
- H94
- 发布
- 2021-05-17
- 实施
- 2021-10-01
Metal strip cold rolled pyramid sleeve reel
- ICS
- 77.180
- CCS
- H94
- 发布
- 2021-05-17
- 实施
- 2021-10-01
Hot rolling mill frame composite sliding plate
- ICS
- 77.180
- CCS
- H94
- 发布
- 2021-05-17
- 实施
- 2021-10-01
Specifications for installation of metallurgical equipment without backing plates
- ICS
- 77.180
- CCS
- H90
- 发布
- 2021-05-17
- 实施
- 2021-10-01
Roller table for steel pipe hot rolling mill
- ICS
- 77.180
- CCS
- H94
- 发布
- 2021-05-17
- 实施
- 2021-10-01
Metal strip cold rolled pyramidal shaft reel
- ICS
- 77.180
- CCS
- H94
- 发布
- 2021-05-17
- 实施
- 2021-10-01
1.1 This guide is intended to establish best practices for recognizing and managing occupational heat stress and heat strain in foundry environments. 1.2 Objectives of the foundry heat stress and heat strain management guide are as follows: 1.2.1 Provide an objective framework for recognizing heat stress and heat strain, and 1.2.2 Facilitate use of best practices to manage heat exposures to minimize heat strain and prevent heat-related illness. 1.3 In this guide, procedures necessary to manage heat stress and heat strain in foundries are described. 1.4 Key elements of this guide include definitions of heat stress and heat strain, plus techniques for recognizing, communicating, managing, and controlling heat stress and heat strain to prevent heat-related illnesses. 1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Managing Heat Stress and Heat Strain in Foundries
- ICS
- 77.180
- CCS
- 发布
- 2021-05-15
- 实施
本文件规定了可控流物料转运系统的术语和定义、工艺设计、运行要求、操作与维护、检测方法。 本文件适用于采用可控流物料转运系统运输铁矿石、铁精粉、煤、焦炭、熔剂等块状和粉状物料的运行与管理。
Controlled flow material transfer system operating procedures
- ICS
- 77.180
- CCS
- C311
- 发布
- 2021-03-22
- 实施
- 2021-03-24
Safety technical requirements for gas combustion system of metallurgical steel rolling heating furnace
- ICS
- 77.180
- CCS
- H 94
- 发布
- 2021-03-11
- 实施
- 2021-04-11
High chromium anti-wear cast iron lining technical conditions
- ICS
- 77.180
- CCS
- H99
- 发布
- 2021-03-05
- 实施
- 2021-07-01
General technical conditions for metallurgical roll surfacing remanufacturing
- ICS
- 77.180
- CCS
- H94
- 发布
- 2021-03-05
- 实施
- 2021-07-01
Technical specifications of universal ball rotating pipe joint
- ICS
- 77.180
- CCS
- H92
- 发布
- 2021-03-05
- 实施
- 2021-07-01
Technical conditions for commonly used perforated plugs for seamless steel pipes
- ICS
- 77.180
- CCS
- H99
- 发布
- 2021-03-05
- 实施
- 2021-07-01
Metallurgical industrial furnace burner technical conditions
- ICS
- 77.180
- CCS
- H99
- 发布
- 2021-03-05
- 实施
- 2021-07-01
Metallurgical industrial furnace burner performance test method
- ICS
- 77.180
- CCS
- H96
- 发布
- 2021-03-05
- 实施
- 2021-07-01
Microcomputer relay protection for metallurgical enterprises Part 2: Inspection procedures
- ICS
- 77.180
- CCS
- H99
- 发布
- 2021-03-05
- 实施
- 2021-07-01
