83.180 粘合剂和胶粘产品 标准查询与下载

ISO/DIS 10364 结构胶粘剂 多元胶粘剂适用期（工作寿命）的测定

Structural adhesives — Determination of the pot life (working life) of multi-component adhesives

T/FSI 121-2023 绝缘栅双极型晶体管用有机硅凝胶

本文件规定了绝缘栅双极型晶体管（简称 IGBT）用有机硅凝胶的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于各种IGBT模块用的双组分加成型有机硅凝胶。

Silicone Gels for Insulated Gate Bipolar Transistors

T/DGGBSH DGGBSH003-2023 水性糊盒胶粘剂基本要求

本文件规定了水性糊盒胶的术语和定义、要求、试验方法、检测规则、标志、包装、贮存和运输要求。 本文件适用于水性糊盒胶的生产、研发、检测、质量评价等环节。

Basic requirements for water-based box paste adhesives

ASTM D6788-02(2023) 可重新定位的压敏标志的标准规范

1.1 This specification covers repositionable pressuresensitive flags used to mark, flag, and index documents, books, periodicals, and so forth. 1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Repositionable Pressure-Sensitive Flags

BS EN 302-2:2023 用于承重木结构的粘合剂 测试方法 抗分层性的测定

1   Scope This document specifies a method for determining the resistance to delamination in glue lines . It is applicable to the following applications: a) for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418; b) for assessing the suitability and quality of adhesives for load-bearing timber structures; c) for comparing the effects on the bond strength resulting from the choice of bonding conditions, from different climatic conditioning and from the treatment of the test pieces before and after bonding. This test does not apply to modified and stabilized wood with strongly reduced swelling and shrinkage properties, such as acetylated wood, heat-treated wood and polymer impregnated wood. This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

Adhesives for load-bearing timber structures. Test methods. Determination of resistance to delamination

BS EN 301:2023 用于承重木结构的酚醛和氨基塑料粘合剂 分类及性能要求

1   Scope This document establishes a classification for phenolic and aminoplastic polycondensation adhesives according to their suitability for use for load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing conditions of load-bearing timber products only. This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions. The performance requirements of this document are applicable to the adhesive only, not to the manufacturing timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood. This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document. Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.

Adhesives, phenolic and aminoplastic, for load-bearing timber structures. Classification and performance requirements

BS ISO 19095-5:2023 塑料 塑料-金属组件粘合界面性能的评估 断裂能

1   Scope This document specifies a method of testing the adhesion in plastic-metal joints produced by several techniques: adhesive bonding, direct joining of thermoplastics by injection or compression moulding, or other methods. More specifically this testing method provides a measure of the joint resistance to fracture in the region between plastic and metal adherends. This method can only be used for comparing adhesives, surface treatments, bonding conditions and effects of environmental conditions. The results cannot be used for engineering design purposes.

Plastics. Evaluation of the adhesion interface performance in plastic-metal assemblies - Fracture energy

BS EN 302-7:2023 用于承重木结构的粘合剂 测试方法 参考条件下工作寿命的确定

1   Scope This document specifies a method for determining the working life for adhesives mixed with hardener for load-bearing timber structures, by a viscosity test. This method does not apply to determining the working life of a multi-component adhesive whose actual working life is very short. This document is only intended for obtaining a reliable basis for comparison between adhesives. The method gives results which cannot be applied to the safe manufacture of timber structures without modifications for the influences of factory temperature and relative air humidity.

Adhesives for load-bearing timber structures. Test methods. Determination of the working life under referenced conditions

BS EN 302-5:2023 用于承重木结构的粘合剂 测试方法 确定参考条件下的最大装配时间

1   Scope This document specifies a laboratory method of determining the maximum assembly time at two spread rate levels in standard atmosphere [20/65]. This document is applicable to obtaining a reliable base of comparison of the maximum assembly time between adhesives at referenced conditions.

Adhesives for load-bearing timber structures. Test methods. Determination of maximum assembly time under referenced conditions

BS EN 16254:2023 粘合剂 用于承重木结构的乳液聚合物异氰酸酯（EPI） 分类及性能要求

1   Scope This document establishes a classification for emulsion polymer isocyanate (EPI) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the industrial manufacture of load-bearing timber products only. The performance requirements of this document are applicable to the adhesives only, not to the timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood. This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. This document only specifies the performance of an adhesive for use in an environment corresponding to the defined conditions. Such an adhesive meeting the requirements of this document for its type is adequate for use in load-bearing timber products, provided that the bonding process has been carried out according to an appropriate product standard.

Adhesives. Emulsion polymer isocyanate (EPI) for load-bearing timber structures. Classification and performance requirements

BS EN 302-4:2023 用于承重木结构的粘合剂 测试方法 测定木材收缩对剪切强度的影响

1   Scope This document specifies a method for determining the influence of shear strength in crosswise gluing by wood shrinkage under drying conditions. It is applicable for the following applications: a) for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418; b) for assessing the suitability and quality of adhesives for load-bearing timber structures; c) for determining if the adhesive is capable of withstanding stresses due to wood shrinkage without unacceptable loss of strength. This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce ( Picea abies L.). This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

Adhesives for load-bearing timber structures. Test methods. Determination of the effects of wood shrinkage on the shear strength

BS EN 302-1:2023 用于承重木结构的粘合剂 试验方法纵向拉伸剪切强度的测定

1   Scope This document specifies a method for determining the shear strength of adhesive bonds in close contact glue line and thick glue line . It is applicable to the following applications: a) for assessing the compliance of adhesives with EN 301, EN 15425, EN 16254, EN 17334 and EN 17418; b) for assessing the suitability and quality of adhesives for load-bearing timber structures. This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This method is not intended for use to provide for structural design and does not necessarily represent the performance of the bonded member in service.

Adhesives for load-bearing timber structures. Test methods - Determination of longitudinal tensile shear strength

BS EN 15425:2023 粘合剂 用于承重木结构的单组分聚氨酯 (PUR) 分类及性能要求

1   Scope This document establishes a classification for one component polyurethane (PUR) adhesives according to their suitability for use in load-bearing timber products in defined climatic exposure conditions, and specifies performance requirements for such adhesives for the factory manufacture or factory-like manufacturing of load-bearing timber products only. It also classifies “ adhesive product lines ” where all the products within the line have the same chemical composition except for a different amount of catalyst. This document only specifies the performance of adhesives for use in an environment corresponding to the defined conditions. The performance requirements of this document are applicable to the adhesives only, not to the manufactured timber products. This document does not cover the performance of adhesives for on-site gluing (except for factory-like conditions) or the production of wood-based panels, except solid wood panels, or modified and stabilized wood with considerably reduced swelling and shrinkage properties, e.g. acetylated wood, heat treated wood and polymer impregnated wood. This document is primarily intended for use by adhesive manufacturers and for use in timber products bonded with adhesives, to assess or control the quality of adhesives. The requirements are applicable to the type testing of the adhesives. Production control activities are outside the scope of this document. Adhesives meeting the requirements of this document are adequate for use in load-bearing timber products, provided that the bonding process has been carried o...

Adhesives. One component polyurethane (PUR) for load-bearing timber structures. Classification and performance requirements

BS EN 302-6:2023 用于承重木结构的粘合剂 测试方法 参考条件下最小压制时间的确定

1   Scope This document specifies a method of determining the minimum pressing time for two glue line thicknesses, close contact glue line and thick glue line (between 0,3 mm and 8 mm), at three temperatures. It is applicable to adhesives used in load-bearing timber products. This document is only intended for obtaining a reliable base of comparison of pressing time between adhesives. The method gives results that cannot be applied to the safe manufacture of timber structures without modifications for the influences of timber density/absorbency, moisture content, factory temperature and relative air humidity.

Adhesives for load-bearing timber structures. Test methods. Determination of the minimum pressing time under referenced conditions

BS EN 302-3:2023 用于承重木结构的粘合剂 测试方法 测定温度和湿度循环对木纤维的酸损伤对横向拉伸强度的影响

1   Scope This document specifies a method for determining the effect on bond strength of damage to wood fibres caused by the action of acids from the adhesive or primer used in the gluing process during climatic cycling. It is applicable to the following applications: a) for assessing the compliance of adhesives with EN 301, EN 15425 and EN 16254; b) for assessing the suitability and quality of adhesives for load-bearing timber structures; c) for determining if the adhesive after bonding has a damaging influence on the strength of the wood due to chemical action. This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This test is carried out on Norway spruce ( Picea abies L.) or Beech ( Fagus sylvatica L.). This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

Adhesives for load-bearing timber structures. Test methods - Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength

T/NBJNJ 002-2023 聚乙酸乙烯酯乳液木材胶粘剂

本文件规定了聚乙酸乙烯酯乳液木材胶粘剂的技术要求、试验方法、检验规则、标志、包装、运输与贮存。

Polyvinyl Acetate Emulsion Wood Adhesive

ISO 19095-5:2023 塑料.塑料-金属组件中粘合界面性能的评定.第5部分：断裂能

This document specifies a method of testing the adhesion in plastic-metal joints produced by several techniques: adhesive bonding, direct joining of thermoplastics by injection or compression moulding, or other methods. More specifically this testing method provides a measure of the joint resistance to fracture in the region between plastic and metal adherends. This method can only be used for comparing adhesives, surface treatments, bonding conditions and effects of environmental conditions. The results cannot be used for engineering design purposes.

Plastics — Evaluation of the adhesion interface performance in plastic-metal assemblies — Part 5: Fracture energy

ASTM D3359-23 胶带试验评定附着力的标准试验方法

1.1 These test methods cover procedures for assessing the adhesion of relatively ductile coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film. 1.2 Test Method A is primarily intended to rate the adhesion of coatings and coating systems greater than 125 µm (5 mils) in total thickness, while Test Method B is primarily intended to rate the adhesion of coatings and coating systems less than 125 µm (5 mils) in total thickness. Test Method B is not considered suitable for films thicker than 125 µm (5 mils) unless wider spaced cuts are employed and there is an explicit agreement between the purchaser and seller. If the thickness of the coating or coating system has not been predetermined, employ the use of a standard such as Practice D7091 or other appropriate standard agreed upon by interested parties prior to proceeding. 1.3 These test methods are used to evaluate whether the adhesion of a coating to a substrate is adequate for the user’s application. They do not distinguish between higher levels of adhesion for which more sophisticated methods of measurement are required. 1.4 This test method is similar in content (but not technically equivalent) to ISO 2409. 1.5 In multicoat systems adhesion failure may occur between coats so that the adhesion of the coating system to the substrate is not determined. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Rating Adhesion by Tape Test

ASTM D7447-08(2023) 粘合剂应用符号化的标准实施规程

1.1 This practice covers a standard symbol that may be used by the design-engineering community on engineering drawings to indicate a bonded assembly for any type of adhesive. 1.2 This design is based on criteria contained in ANSI/AWS A2.4 as well as ISO 15785. 1.3 The values given in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Symbolizing Adhesive Applications

ASTM D3310-00(2023) 测定粘性材料腐蚀性的标准试验方法

1.1 This test method is intended to determine whether an adhesive material, cured or uncured, is corrosive to a metal. It is a general test method intended to screen out those materials that give a visible sign of corrosion. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Corrosivity of Adhesive Materials