83.200 橡胶和塑料工业设备 标准查询与下载
共找到 545 条与 橡胶和塑料工业设备 相关的标准，共 37 页
This document specifies safety requirements relating to the design and construction of calenders (see 3.1.1) intended for the calendering, polishing, laminating or embossing of rubber or plastics. This document concerns the calender alone, including the following integrated components: cutting device, stock guides and feeding device, secondary roller. Annex C shows examples of various types of calenders and Annex D shows examples of calendaring processes. This document deals with all significant hazards, hazardous situations or hazardous events relevant to the design and construction of calenders, when the machines are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer during all the phases of the life of the machine as described in EN ISO 12100:2010, 5.4 (see Annex B). This document does not deal with: - hazards generated by the processing of explosive materials, or materials which give rise to an explosive atmosphere; - hazards due to laser or ionizing radiation; - hazards generated if the calender is installed in an explosive atmosphere. Two roll mills are covered by EN 1417. This document is not applicable to calenders manufactured before the date of its publication.
Plastics and rubber machines - Calenders - Safety requirements
- ICS
- 83.200
- CCS
- 发布
- 2021-10-06
- 实施
This International Standard specifies the essential safety requirements for the design and construction of injection moulding machines for the processing of plastics and/or rubber and provides information for their safe use. This standard is applicable to injection moulding machi
Plastics and rubber machines - Injection moulding machines - Safety requirements (ISO 20430:2020); German version EN ISO 20430:2020
- ICS
- 83.200
- CCS
- G95
- 发布
- 2021-10-01
- 实施
Plastics and rubber machines - Two-roll mills - Safety requirements
- ICS
- 83.200
- CCS
- 发布
- 2021-10-00
- 实施
Plastics－Verification of pendulum impact-testing machines－Charpy, Izod and tensile impact-testing
- ICS
- 83.200
- CCS
- 发布
- 20210924
- 实施
- 20210924
本文件规定了悬浮式塑料圆织机的术语和定义、结构与基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于塑料编织布、编织袋生产的悬浮式塑料圆织机（以下简称圆织机）。
Shuttle suspension plastic circular loom
- ICS
- 83.200
- CCS
- C352
- 发布
- 2021-09-15
- 实施
- 2021-10-03
本文件规定了冲压式合模机的术语和定义、基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、贮存、运输和质量承诺。 本文件适用油压驱动、最大上模（旋转）重量不超过18 t的冲压式合模机（以下简称“合模机”）。
Stamping die spotting machines
- ICS
- 83.200
- CCS
- C352
- 发布
- 2021-08-13
- 实施
- 2021-08-19
本文件规定了塑料机械用氮化单螺杆、机筒的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本文件适用于单螺杆塑料挤出机和塑料注射成型机等塑料机械用表面氮化处理的螺杆和机筒。
Nitriding single screw and barrel for plastic machinery
- ICS
- 83.200
- CCS
- C352
- 发布
- 2021-07-26
- 实施
- 2021-08-12
Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements for agglomerators (Amendment)
- ICS
- 83.200
- CCS
- 发布
- 2021-05-01
- 实施
- 2021-05-01
本文件确立了立柱型抽真空式平板硫化机的术语与定义、 基本参数、 基本要求、 技术要求、 试验方法、检验规则、 标志、说明书、包装、运输和贮存、质量承诺。 本文件适用于模压成型橡塑制品、胶带（板） 硫化用立柱型抽真空式平板硫化机（以下简称“平板硫化机”）。 本文件不适用于橡胶塑料发泡用平板硫化机
Pillar type vacuum daylight press
- ICS
- 83.200
- CCS
- C352
- 发布
- 2021-04-24
- 实施
- 2021-05-27
Plastics Machinery - Safety Requirements for Granulators, Strand Pelletizers, Dicers and Single Shaft Rotary Grinders Used for Plastic Materials (PIA)
- ICS
- 83.200
- CCS
- G95
- 发布
- 2021-04-12
- 实施
Rubber and plastics test equipment — Tensile, flexural and compression types(constant rate of traverse) — Specification
- ICS
- 83.200
- CCS
- 发布
- 2021-03-16
- 实施
Rubber and plastics test equipment — Tensile, flexural and compression types(constant rate of traverse) — Specification
- ICS
- 83.200
- CCS
- 发布
- 2021-03-16
- 实施
Plastics and rubber machines -- Injection moulding machines -- Safety requirements (ISO 20430:2020)
- ICS
- 83.200
- CCS
- 发布
- 2020-12-31
- 实施
- 2020-12-31
1 范围 本文件规定了塑料流延成型设备 陶瓷电晕辊的术语和定义、型号与分类、技术要求、检查和测试方法、检验规则、标志、包装、运输和贮存。 本文件适用于塑料流延成型设备用的陶瓷电晕辊。 2 规范性引用文件 3 术语和定义 4 产品结构、型号与分类 4.1 型号命名 4.2 分类 4.2.1 叶片结构 4.2.2 叶片旋向 4.2.3 叶片头数 5 需求 6 试验方法 6.1 外观质量要求检测 6.2 辊筒内水路的耐压及通畅试验 6.3 主要尺寸检测 6.4 辊面径向全跳动 6.5 辊筒平衡检验 6.6 辊面温差 6.7 辊面表面粗糙度 6.8 辊面涂层厚度 6.9 辊面涂层微孔 6.10 焊缝质量检测 6.11 辊筒主要构件的材质抗拉强度检测 6.12 金相显微检查 6.13 金相试样涂层厚度 6.14 界面分离 6.15 界面污染 6.16 裂纹 6.17 孔隙率 6.18 未熔颗粒 6.19 涂层显微硬度 6.20 结合强度 7 检验规则 7.1 检验分类 7.2 出厂检验 7.3 型式检验 7.4 判定规则 8 标志、包装、运输和贮存 8.1 标志 8.2 包装 8.3 运输 8.4 贮存
Plastic cast film machine － Technical requirements for ceramic corona roll
- ICS
- 83.200
- CCS
- C352
- 发布
- 2020-12-11
- 实施
- 2020-12-14
Test code for performance and accuracy of shell moulding machines
- ICS
- 83.200
- CCS
- 发布
- 20201117
- 实施
- 20201117
1 范围 本文件规定了新能源电池用铝塑膜（PP基材）流延成型设备的术语和定义、型式与基本参数。 本文件适用于采用单螺杆挤出流延工艺生产新能源电池用铝塑膜（PP基材）流延成型设备（以下简称机组）。 本文件不适用于其它基材。 2 规范性引用文件 3 术语和定义 4 型式 5 基本参数
Types and basic parameters of aluminum-plastic film tape casting equipment for new energy batteries
- ICS
- 83.200
- CCS
- C352
- 发布
- 2020-09-30
- 实施
- 2020-10-10
1 Scope This document specifies requirements for tensile-testing systems operating at constant rate of traverse and suitable for testing rubbers, plastics and adhesives, although any one system might only be applicable to a narrower range of materials. It also covers such systems when used for flexural, shear and compression tests.
Rubber and plastics test equipment. Tensile, flexural and compression types (constant rate of traverse). Specification
- ICS
- 83.200
- CCS
- 发布
- 2020-09-30
- 实施
- 2020-09-30
1 范围 本文件规定了锂电池隔膜（干法）流延成型设备的术语和定义、型式与基本参数。 本文件适用于采用单螺杆挤出流延工艺生产锂电池隔膜（干法）的流延成型设备（以下简称机组）。 本文件不适用于湿法。 2 规范性引用文件 3 术语和定义 4 型式 5 基本参数
Diaphragm (dry) tape casting equipment type and basic parameters
- ICS
- 83.200
- CCS
- C352
- 发布
- 2020-09-30
- 实施
- 2020-10-10
1 范围 本文件规定了塑料流延成型设备光伏背板聚偏氟乙烯（PVDF）膜机组的术语和定义、型式与基本参数。 本文件适用于采用单螺杆挤出流延光伏背板聚偏氟乙烯（PVDF）膜流延成型设备。 2 规范性引用文件 3 术语和定义 4 型式 5 基本参数
Types and basic parameters of polyvinylidene fluoride (PVDF) film tape casting equipment for photovoltaic backplanes
- ICS
- 83.200
- CCS
- C352
- 发布
- 2020-09-30
- 实施
- 2020-10-10
