87.020 涂料涂覆工艺 标准查询与下载

SH/T 3603-2009 石油化工钢结构防腐蚀涂料应用技术规程

本规程规定了石油化工钢结构防腐蚀涂料使用环境的腐蚀性分级、涂层干膜厚度和配套要求、施工检验以及安全、卫生和环境保护方面的要求。 本规程适用于受气态介质腐蚀作用下的石油化工钢结构防腐蚀涂料的应用、施工及验收。不适用于钢制设备，不适用于其他介质及由于杂散电流引起的钢结构腐蚀。

Technical specification for the coating anticorrosion of steel structures in petrochemical industry

ASTM D1731-09(2014) 涂漆热浸铝表面预处理的标准实施规程

1.1 These practices describe procedures for the preparation of hot-dip aluminum surfaces for painting. 1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practices for Preparation of Hot-Dip Aluminum Surfaces for Painting

ASTM D1730-09(2014) 涂漆铝和铝合金表面预处理的标准实施规程

1.1 These practices cover four types of treatment for preparation of aluminum and aluminum-alloy surfaces for painting, as follows: 1.1.1 Type A—Solvent Cleaning. 1.1.2 Type B—Chemical Treatments. 1.1.3 Type C—Anodic Treatments. 1.1.4 Type D—Mechanical Treatments. These four types cover a number of procedures, as described herein. 1.2 Variations in surface treatment produce end conditions which differ, and which do not necessarily yield identical results when paints are applied. Service conditions will dictate the type of surface preparation that should be selected, although the quality produced by any individual method may vary with different alloys. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practices for Preparation of Aluminum and Aluminum-Alloy Surfaces for Painting

KS M ISO 12944-8:2008 涂料和清漆.防护漆系统对钢结构的腐蚀防护.第8部分:新工艺和维修规范的开发

이 표준은 방식도료 시스템을 사용하여 강철 구조물의 부식을 방지하기 위한 표준의 작성방법에

Paints and varnishes－Corrosion protection of steel structures by protective paint systems－Part 8：Development of specifications for new work and maintenance

KS M ISO 12944-7:2008 涂料和清漆.防护漆系统对钢结构的腐蚀防护.第7部分:涂漆工艺的实施和管理

1.1 이 표준은 실내 작업장이나 또는 옥외에서 강철 구조물에 대한 도장 작업의 실행과 감

Paints and varnishes－Corrosion protection of steel structures by protective paint systems－Part 7：Execution and supervision of paint work

KS M ISO 12944-6:2008 涂料和清漆.防护漆系统对钢结构的腐蚀防护.第6部分:实验室性能试验方法

이 표준에서는 강철 구조물의 부식 방지용 도료 시스템을 평가하기 위한 실험실적 시험방법과

Paints and varnishes－Corrosion protection of steel structures by protective paint systems－Part 6：Laboratory performance test methods

KS M ISO 12944-4:2008 涂料和清漆.防护漆系统对钢结构的腐蚀防护.第4部分:表面类型和表面处理

이 표준은 탄소 또는 저합금강으로 구성된 강철 구조물의 다음의 표면 유형과 표면 처리에 대

Paints and varnishes－Corrosion protection of steel structures by protective paint systems－Part 4：Types of surface and surface preparation

KS M ISO 12944-3:2008 涂料和清漆.防护漆系统对钢结构的腐蚀防护.第3部分:设计上的考虑

이 표준은 구조물 또는 도막의 물성 저하와 빠른 부식을 피하기 위하여 방식도료 시스템에 의

Paints and varnishes－Corrosion protection of steel structures by protective paint systems－Part 3：Design considerations

KS M ISO 12944-2:2008 涂料和清漆.防护漆系统对钢结构的腐蚀防护.第2部分:环境分类

1.1 이 표준은 강철 구조물이 폭로될 주요 환경의 등급과 이들 환경의 부식성에 대해서 규

Paints and varnishes－Corrosion protection of steel structures by protective paint systems－Part 2：Classification of environments

KS M ISO 12944-1:2008 涂料和清漆.防护漆系统对钢结构的腐蚀防护.第1部分:一般性介绍

1.1 이 표준은 방식도료 시스템에 의한 강철 구조물의 부식 방지에 대하여 규정한다.1

Paints and varnishes-Corrosion protection of steel structures by protective paint systems-Part 1:General introduction

KS M ISO 15741:2008 涂料和清漆.海上和近海的非腐蚀气体钢管内侧的减小摩擦涂层

이 표준은 액상 에폭시 도료와 그러한 도료를 비부식성 가스의 운송을 위한 강철관과 그 부속

Paints and varnishes－Friction-reduction coatings for the interior of on-and offshore steel pipelines for non-corrosive gases

GSO ASTM D7073:2008 染色工作中使用的刷子或滚筒的评估指南

1.1 This guide describes procedures for the application of brush or roller, or both, applied paint films to sealed wallboard for evaluating application properties. 1.2 Because both the application and panel evaluation are subjective, this guide should be used only for comparative testing within one laboratory using one operator for each set of applications, as the ratings assigned by different laboratories may not agree. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Guide for Application and Evaluation of Brush and Roller Applied Paint Films

DS-håndbog 124:2008 保护漆系统对钢结构的腐蚀保护

This handbook deals with corrosion protection of steel structures by protective paint system. It also contains the coulour codes and the qualification of inspectors for corrosion protection.

Corrosion protection of steel structures by protective paint systems

DS/EN ISO 12944-5:2008 油漆和清漆 通过防护漆系统对钢结构的腐蚀防护 第5部分：防护漆系统

This part of ISO 12944 describes the types of paint and paint system commonly used for corrosion protection of steel structures. It also provides guidance for the selection of paint systems available for different environments (see ISO 12944-2) and different surface preparation grades (see ISO 12944-4), and the durability grade to be expected (see ISO 12944-1). The durability of paint systems is classified in terms of low, medium and high.

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5: Protective paint systems

ASTM D6578-08 耐涂写性测定的标准实施规程

Graffiti on building and structures is an ongoing and increasing problem. A number of coatings have been produced that are intended to be resistant to the application of a graffiti marking, or to provide a surface from which such markings can be easily removed. The procedures described in this practice provide a standard set of conditions that can be used to evaluate the graffiti resistance of a surface. Graffiti resistance determined according to this practice is applicable to smooth surfaces. Graffiti resistance of the same coatings applied to a rough or textured surface may be lower. Graffiti resistance of coatings determined after natural or laboratory accelerated weathering, either before or after marking, conducted according to this practice, is considered as having more weight than graffiti resistance of the same coating determined without weathering. Graffiti resistance of coatings determined after natural weathering should be considered as having more weight than graffiti resistance determined after laboratory accelerated weathering.1.1 This practice covers a basic method for evaluating graffiti resistance of coatings, and use of this practice to evaluate graffiti resistance of coatings after outdoor or laboratory accelerated exposure (either prior to or after graffiti is applied). Graffiti resistance is based on how a defined set of markings is removed by a defined set of cleaning agents. 1.2 This practice also defines procedures (optional) to evaluate graffiti removal after re-marking with subsequent re-cleaning. It does not address recoatability after a coating is no longer graffiti resistant. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determination of Graffiti Resistance

LST EN ISO 12944-5:2007 油漆和清漆 通过防护漆系统对钢结构的腐蚀保护 第5部分：防护漆系统（ISO 12944-5:2007）

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5: Protective paint systems (ISO 12944-5:2007)

NF T34-555-5:2007 涂料和清漆.用防护漆系统对钢结构的腐蚀保护.第5部分:防护涂料系统

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5 : protective paint systems.

BS EN ISO 12944-5:2007 涂料和清漆.防护涂料系统对钢结构的腐蚀防护.防护涂料系统

ISO 12944-5:2007 describes the types of paint and paint system commonly used for corrosion protection of steel structures. It also provides guidance for the selection of paint systems available for different environments and different surface preparation grades, and the durability grade to be expected. The durability of paint systems is classified in terms of low, medium and high.

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Protective paint systems

DS/EN ISO 16276-2:2007 通过防护漆系统对钢结构的腐蚀保护 涂层的附着力/内聚力（断裂强度）的评估和验收标准 第2部分：横切测试和 X 切测试

This part of ISO 16276 specifies procedures for rating the resistance of coating systems when a cut in the form of a right-angle lattice pattern (cross-cut) or in the form of an X (X-cut) is made into the coating, penetrating through to the substrate.This part of ISO 16276 is only applicable if the cross-cut or X-cut test method is specified, together with the rating from the appropriate rating scale.NOTE The characteristics of the coating can make the assessment of the result of a cross-cut or X-cut test difficult.This part of ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria.It does

Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 2: Cross-cut testing and X-cut testing

LST EN ISO 16276-2:2007 通过防护漆系统对钢结构的腐蚀防护 涂层附着力/内聚力（断裂强度）的评估和验收标准 第2部分：横切测试和 X 切测试（ISO 16276-2:2007）

Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 2: Cross-cut testing and X-cut testing (ISO 16276-2:2007)