91.090 外围建筑物 标准查询与下载

BS 1722-16:2009 围墙.用作部件和筛孔的塑料精饰的粉末涂料的规范

This part of BS 1722 specifies performance requirements and describes methods for laboratory testing of powder coatings and the applied powder coatings used as a finish to fence components and mesh. NOTE Annex A gives some guidance on the care and protection of plastics finishes.

Fences - Specification for powder coatings used as a plastics finish to components and mesh

DS/EN 12635+A1:2009 工业、商业和车库门和大门 安装和使用

1.1 GeneralThis European Standard specifies the information to be provided by the door manufacturer and the components manufacturer to ensure safe installation, operation, use (including maintenance and repair) of doors, gates and barriers intended for installation in areas in the reach of persons, and for which the main intended uses are giving safe access for goods and vehicles accompanied or driven by persons in industrial, commercial or residential premises.This European Standard also covers commercial doors such as rolling shutters and rolling grilles used in retail premises which are mainly provided for the access of persons rather than vehicles or go

Industrial, commercial and garage doors and gates - Installation and use

JIS A 6603:2008 钢棚

This Japanese Industrial Standard specifies the steel sheds [hereafter referred to as "sheds" and its construction members (hereafter referred to as "members"). How- ever, the sheds with shutter-type doors or those commonly used as the garage are excluded. The foundation is not included in this Standard. Note : A "shed" is a storage for storing articles, which is mainly built of steel sheets and steel members.

Steel sheds

JIS A 6518 AMD 1:2008 铁丝网栏栅的组件(修改件1)

Components for wire net fences (Amendment 1)

SANS 280:2008 围栏立柱和吊索孔洞的位置确定

Lays down requirements for the location of holes for the positioning of fencing wires in 6 types of fencing posts and droppers.

Hole location in fencing posts and droppers

JIS A 6604:2007 停车场用金属零部件

この規格は，主として住宅で使用する金属製の簡易車庫用構成材(以下，車庫用構成材という。)について規定する。この規格は,屋根ふき材を除いたもので,屋根が片側柱又は両側柱によって支持される形式のものについて適用する。ただし,周囲を囲うもの,収納庫をもつもの及び基礎は除く。

Metal components for car port

ASTM F2408-07 使用镀锌钢管的装饰栅栏的标准规范

1.1 This specification establishes the minimum requirements for coated tubular picket ornamental fence systems fabricated from galvanized steel components.1.2 The requirements of this specification do not apply to vertical bar fence systems utilizing solid bar or wrought iron materials.1.3 The values stated with in-pound units are to be regarded as standard. The SI values in brackets are provided for information.

Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets

CSA S413-2007(R2012) 停车设施

1 Scope 1.1 General This Standard specifies special requirements for the durability aspects of the design and construction of new parking structures and parts of buildings subject to vehicular traffic. 1.2 Structure types New parking structures constructed of structural steel, reinforced concrete (including prestressed concrete), or a combination of these materials fall within the scope of this Standard. 1.3 Repair of existing parking structures This Standard does not cover the repair of existing parking structures, and the provisions of this Standard are not necessarily appropriate for the repair and protection of existing structures. Note: Repair of concrete structures is covered in CSA S448.1. 1.4 Reference standards In the event of conflict between this Standard and the reference standards, this Standard takes precedence. 1.5 Terminology In CSA Standards, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the Standard; and "can" is used to express possibility or capability. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Parking Structures

JIS A 6513 AMD 1:2007 金属制栅栏和门(修改件1)

Fences and gates with metals (Amendment 1)

BS DD 1722-18:2007 栏栅.场地周边临时设置钢网栅栏规范

This Draft for Development specifies requirements for the manufacture of steel mesh site perimeter temporary fencing. It includes requirements for the dimensions and construction of fence components. Annex A describes a test method to be used by manufacturers or vendors to determine the wind resistance of the fence. Annex B gives recommendations for the installation of a steel mesh site perimeter temporary fencing system to be provided to vendors and users of the fencing system. Annex C gives recommendations for the renovation of damaged areas of pre-galvanized coating on fence panels. NOTE This Draft for Development complements and expands on the guidance given by the Health & Safety Executive in its guidance document HS G 151, Protecting the public, your next move [1]. This document is intended to assist the construction industry and assist in ensuring the safety of members of the public in the UK.

Fences - Specification for steel mesh site perimeter temporary fencing systems

BS 1722-7:2006 栏栅.木柱和栏栅用规范

This part of BS 1722 specifies requirements for wooden post and rail fences, using both sawn and cleft components. It includes requirements for the installation of the fencing at the specified location.

Fences - Specification for wooden post and rail fences

BS 1722-2:2006 栅栏.应变金属丝和金属丝网栅栏用规范

This part of BS 1722 specifies requirements for the construction and installation of general pattern and dropper pattern strained wire fences and rectangular wire mesh fences, including mild steel or high tensile woven wire fencing, welded mesh fencing, hexagonal wire netting fences of the general pattern, and spring steel wire pattern fences where the mesh is fixed onto spring steel line wires. This standard includes requirements for protective treatments. However, maintenance requirements of the fence after installation are outside the scope of this standard. NOTE Figure 1 illustrates the general characteristics of strained wire fences. It is not intended to illustrate any particular requirements of this standard but provides guidance as to the general layout of a typical fence, and on the terminology associated with this form of fencing.

Fences.Part 2:Specification for strained wire and wire mesh netting fences

BS 1722-17:2006 栅栏.电子安全栅栏用规范.设计、安装和维护

This British Standard specifies requirements for the design, installation and maintenance of electric security fences. This standard is not intended to cover the installation of any carrier fence or supporting structure and therefore should be read in conjunction of the appropriate part of BS 1722 for the type of carrier fence employed. It is applicable to installations where the electric security fence is to provide both a deterrent effect and a physical barrier. It is not intended that this British Standard outlines the specific method to be used in construction. Construction specifics are covered in the appointed approved manufacturers installation courses and material available only to accredited installation dealers and marketing partners.

Fences - Specification for electric security fences - Design, installation and maintenance

BS 1722-14:2006 栅栏.开放筛网钢片栅栏用规范

This part of BS 1722 specifies requirements for the following categories of open mesh steel panel fences: a) Category 1: general purpose fences up to 2 400 mm high. b) Category 2: security fences at least 2 400 mm high. c) Category 3: high security fences at least 3 000 mm high. d) Category 4: extra high security fences at least 3 000 mm high. Requirements for the performance of panel fences for this standard are based upon loadings described in Clause 5. Maintenance of the fence after installation is outside the scope of the standard.

Fences - Specification for open mesh steel panel fences

BS 1722-12:2006 栅栏.钢制栅栏用规范

This part of BS 1722 specifies requirements for steel palisade fences and gates for general purposes (“GP” fences) in corrugated and angle pales for heights up to 2.4 m, and for security purposes (“SP” fences) in corrugated pales for heights of 3.0 m and 3.6 m, all with posts at 2.75 m centres. This standard also covers fences between 2.4 m and 3.0 m in height with components constructed to the SP specification.

Fences – Part 12: Specification for steel palisade fences

BS 1722-11:2006 栅栏.预制木栅栏用规范

This part of BS 1722 specifies requirements for the materials, design, construction and installation of prefabricated wood panel fences constructed from softwood panels fixed between timber or concrete posts. This standard does not cover fences of a height greater than 2 m above ground level. This standard includes requirements for protective treatments. However, maintenance requirements of the fence after installation are outside the scope of this standard. It specifies requirements for the components that make up a fence and the way in which the fence should be constructed. The standard includes requirements for component dimensions, together with the permissible tolerances on size. These are minimum requirements and it will normally be acceptable to use larger sizes, except if this could adversely affect the fitting of components or if replacement parts are required to match with those already present.

Fences - Specification for prefabricated wood panel fences

BS 1722-10:2006 栅栏.链节和焊接筛网的防盗栅栏用规范

This part of BS 1722 specifies requirements for anti-intruder chain link or welded mesh fences and gates of at least 2.4 m in height for situations that require a higher level of protection than that offered by fences conforming to BS 1722-1. It also includes requirements for the installation of the fencing at the specified location. Provision is made for either single or double extension arms. This standard includes requirements for component dimensions, together with the permissible tolerances on size. These are minimum requirements and it should normally be acceptable to use larger sizes, except if this could otherwise adversely affect the fitting of components or if replacement parts are required to match with those already present. This standard includes requirements for protective treatments. However, maintenance requirements for the fence after installation are outside the scope of this standard. It specifies concrete or steel posts and struts, steel gates and gate posts and zinc coated or plastic coated zinc coated wire or mesh infill. This standard specifies requirements for fence materials and their combination and installation. Because a fence is made up of a number of separate components of which the particular features vary, e.g. zinc coated or plastic coated wire, a number of combinations are available to the user. Annex C provides details of the fence requirements and installation site that should be agreed between the fence supplier and purchaser at the time of ordering a fence. However, as conditions vary from site to site, Annex C should not be assumed to be exhaustive.

Fences - Specification for anti-intruder fences in chain link and welded mesh

BS 1722-9:2006 栅栏.带圆形或方形竖杆和扁平横杆的低碳钢栅栏用规范

This part of BS 1722 specifies requirements for self-adjusting (nibbed) or welded mild steel (low carbon steel) fences with round or square verticals and rolled hollow section (RHS) or rolled steel joist (RSJ) posts and flat horizontals. It also specifies requirements for their installation. Maintenance of the fence after installation is outside the scope of this standard.

Fences - Specification for mild steel (low carbon steel) fences with round or square verticals and flat horizontals

BS 1722-8:2006 栅栏.低碳钢链条链接栅栏和篱笆用规范

This part of BS 1722 specifies requirements for mild steel (low carbon steel) continuous bar fences for farm animal containment applications and welded hurdle fences of continuous bar type. A range of five specifications of fence of both types available, in three heights, is listed in Table 1 and Table 3. Requirements for the construction of suitable gates for these fences is given in Clause 5, which states certain functional requirements for the designs, but does not specify the designs in detail. A list of information that should be obtained from the purchaser at the time of enquiry and/or order is given in Annex A.

Fences - Specification for mild steel (low carbon steel) continuous bar fences and hurdles

BS 1722-1:2006 栅栏.金属防护网用规范

This part of BS 1722 specifies requirements for chain link fences and gates and gateposts for use with chain link fences. The gates specified are steel with a provision for chain link infill or other infill if required by the purchaser. This standard specifies requirements for fences up to 2.5 m in height with a chain link mesh infill. For other security fences, refer to BS 1722-10, BS 1722-12 and BS 1722-14, and for chain link fences for tennis court surrounds refer to BS 1722-13. This standard specifies a method of allocating a reference code to each type of fence, indicating its height, the type and weight of infill, and the materials of the posts and the type of wire coating. This standard is divided into requirements for the material components for fences and for installation of the fences. This standard also includes requirements for protective treatments. However, maintenance requirements for the fence after installation are outside the scope of this standard. This standard includes requirements for sizes of components, together with the permissible tolerances on size. These are minimum requirements, and it will normally be acceptable to use larger sizes, except if this could adversely affect the fitting of components, or if replacement parts are required to match with those already present.

Fences - Specification for chain link fences