91.180 内部装修 标准查询与下载

T/CBDA 47-2021 建筑室内装饰装修制图标准

主要技术内容是：1.总则；2.术语；3.基本规定；4.常用材料和设备图例；5.图样画法；6.计算机辅助制图。

Standard for drawings of building interior decoration and renovation

T/ZZXJX 003-2020 居住建筑室内装配式装修工程技术规程

前  言　 1 范围 2 规范性引用文件 3 术语和定义 4 基本规定 4.1 一 般 规 定 4.2 部品和材料 4.3 室 内 环 境 5 设  计　 5.1 一 般 规 定 5.2 部品集成设计和选用 5.3 设备与管线设计　 6 部 品 生 产　 6.1 一 般 规 定　 6.2 生 产 加 工　 6.3 质 量 检 验　 6.4 包装、运输及堆放　 7 施  工　 7.1 一 般 规 定　 7.2 部 品 施 工　 7.3 设备与管线施工　 8 工程质量验收　 8.1 一 般 规 定　 8.2 装配式隔墙　 8.3 装配式吊顶　 8.4 装配式楼地面　 8.5 集 成 厨 房　 8.6 集成卫生间　 8.7 给水排水工程　 8.8 暖  通　 8.9 电  气　 8.10 智 能 化　

Technical specification for interior assembly decoration engineering of residential buildings

T/CICE 002-2020 建筑装饰装修工程施工工艺规范

本文件旨在规范建筑装饰装修工程的施工工艺，保证工程质量。由 19 个章节和 9 个附录组成，主要内容包括：范围、规范性引用文件、术语和定义、基本规定、基层工程、防水工程、门窗工程、吊顶工程、轻质隔墙工程、抹灰工程、墙饰面工程、建筑地面装饰工程、涂饰工程、细部工程、给排水管道安装工程、卫浴器具工程、厨房工程、电气工程、通风与空调安装工程等。

Standard for construction technology of building decoration

LST EN 266-2020 卷状墙面覆盖物 纺织墙面覆盖物规范

Wall coverings in roll form - Specification for textile wall coverings

DB43/T 1879-2020 城镇住宅室内装饰装修设计规范

Specifications for interior decoration and decoration design of urban residences

T/XMTM 1-2020 建筑装饰装修施工常见质量问题防治技术措施

总则、术语、建筑装饰装修工程、其它分项工程

Construction of building decoration Technical measures for prevention and control of common quality problems

OENORM EN 266-2020 卷状墙面覆盖物 纺织墙面覆盖物规范

Wall coverings in roll form - Specification for textile wall coverings

UNI EN 266-2020 卷状墙面覆盖物 纺织墙面覆盖物规范

Wall coverings in roll form - Specification for textile wall coverings

ASTM F793/F793M-20 墙体使用特性的标准分类

1.1 This classification covers the classification of wall coverings by use characteristics, that is, according to their serviceability in use, recognizing that certain wall coverings are designed primarily for decorative effect, while other wall coverings are also designed to achieve a high degree of serviceability. 1.1.1 This classification applies to any wall covering but some sections apply specifically to vinyl-coated wall covering materials. 1.1.2 Whenever this classification refers to wall coverings, it is intended also to refer to ceiling coverings of the same type. 1.1.3 This classification does not apply to wall coverings intended to be applied to exterior walls. 1.1.4 This classification does not apply to rigid panel products, irrespective of whether or not they include a flexible lining or veneer. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard. 1.3 This standard is used to measure and describe the properties of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification of Wall Coverings by Use Characteristics

ASTM F1141/F1141M-20 墙面标准规范

1.1 This specification covers the performance, quality, packaging, and marking characteristics of flexible wall coverings as finished products. 1.1.1 Whenever this specification refers to wall coverings, it is intended also to refer to ceiling coverings of the same type. 1.1.2 This specification does not apply to wall coverings intended to be applied to exterior walls. 1.1.3 This specification does not apply to rigid panel products, irrespective of whether or not they include a flexible lining or veneer. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Wall Coverings

BS EN 266:2020 卷状墙面覆盖物 纺织墙面覆盖物规范

What is BS EN 266 about?    BS EN 266 covers specifications for textile wall coverings. BS EN 266 applies to textile wallcoverings supplied in rolls for hanging on walls and ceilings by means of an adhesive. This adhesive goes across the whole interface between the wallcovering and the support surface . Various grades of colour fastness to light of textile wallcoverings are permitted and symbols to indicate these grades are given in BS EN 266 .   Note 1: Excluded from BS EN 266 are rigid materials, materials not attached or not wholly attached by adhesive, and non-decorative wallcoverings such as wall linings or those with special properties, e.g., thermal, or acoustic insulation.  Who is BS EN 266 for?   BS EN 266 on wallcoverings in roll form is useful for:   Wallcovering manufacturers

Wall coverings in roll form. Specification for textile wall coverings

KS F 2601-2020 用O-Y拉滑仪测定地板滑动性的标准试验方法

Standard test method for floor slipperiness using the O-Y Pull Slip Meter

T/STCHWJ 01-2020 塑柄油灰刀

        本标准规定了油灰刀的分类与命名、技术要求、试验方法、检验规则、标志、标签、包装、   运输、贮存等内容。

Plastic handle putty knife

T/CAME 16-2020 医用家具配置

本文件规定了医疗机构各功能分区单元用房医用家具的配置要求。 

Medical furniture arrangement

T/LWB 028-2020 装饰用石膏

抗折  ≥5.0

decorative plaster

T/XYZL 01-2020 钢质室内门

 产品分类 产品按门扇开关方向代号进行分类 ——顺时针方向，由内向外关，代号为5.0； ——顺时针方向，由外向内关，代号为5.1； ——逆时针方向，由内向外关，代号为6.0； ——逆时针方向，由外向内关，代号为6.1。 4  规格型号 4.1 规格 应与GB/T 5824规定的规格相对应，特殊规格的可按用户需要生产。 T/XYZL01－2020 4.2 型号 　SNM  —□ —　□ —　□                                               设计序号（以A、B、C等表示）                                          门扇规格（宽×高×厚），单位为毫米                                           开关门方向代号                                                室内门                                              如SNM——5.0——880×2050×50——A表示为顺时针方向，由内向外关，门扇规格为880×2050×50，第一次设计的室内门。 5　技术要求 5.1 表面质量 5.1.1  钢质室内门表面应无明显的凹痕和机械损伤；表面漆膜应均匀，色泽一致，不得有明显的流挂、脱落、露底等缺陷，电镀色泽均匀，镀层无脱落。 5.1.2  漆膜附着力应不低于GB/T 1720—1979的三级。 5.1.3  漆膜耐冲击按GB/T 1732 的规定执行，要求应不低于50cm。 5.2 门扇、门框 5.2.1  钢质室内门选用的钢质材料应符合GB/T 11253的有关的规定，门框（套）用的钢质材料厚度应不小于0.7mm,门扇用钢质材料厚度应不小于0.3mm。 5.2.2  尺寸偏差与形位公差 5.2.2.1  门扇厚度为（40～90）±5mm。 5.2.2.2  门框上锁孔与锁舌（栓）的最大配合间隙应不大于10mm。 5.2.2.3  门扇表面平度不应大于6mm/㎡。 5.2.2.4  门框槽口对角线尺寸之差不应大于7mm。 5.2.3  框扇配合  5.2.3.1  门扇与门框的搭接宽度不应小于6 mm，门扇与门框配合活动间隙不应大于6 mm。 5.2.3.2  门扇与门框铰链边贴合面间隙不应大于6 mm，门扇在关门状态与门框贴合面间隙不应大于6mm。 5.2.4   门扇在30㎏沙袋软冲击载荷作用3次后，不应产生大于10 mm的凹变形。 5.3  门铰链 5.3.1   门扇开启90°过程中，不应产生分倾斜、门铰链轴线不应产生大于3 mm的位移。 T/XYZL01－2020 5.3.2   门铰应转动灵活，在49N拉力作用下门体灵活转动90°。 5.3.3   产品应进行悬端吊重试验，载500N作用下，残余变形应不大于2mm，启闭应正常。 5.4  门锁 钢质室内门上安装的门锁应符合GA/T 73中A级或QB/T 2474的规定。 5.5  橡胶密封条 应符合GB/T 12002规定的要求。

steel interior door

T/CBDA 40-2020 展览陈列工程技术规程

本规程主要技术内容是1.总则；2.术语；3.基本规定；4.设计；5.材料设备；6.展览陈列基础工程施工；7.展览制作；8.安装调试；9.竣工验收；10.交付维保等。

Technical Specifications for exhibition constructions

T/CBDA 39-2020 光电建筑技术应用规程

1.总则；2.术语和符号；3.基本规定；4.材料、构件与设备；5.光电建筑围护系统设计；6.光伏发电系统设计；7.光伏发电系统接入设计；8.构件与支承结构制作；9.安装施工；10.维护系统、光伏发电系统测试；11.验收。

Specification for application of photovoltaic building technology

T/CBDA 38-2020 老年人设施室内装饰装修技术规程

1.总则；2.术语；3.基本规定；4.设计；5.材料；6.施工；7.验收。

Technical code for interior decoration of facilities for the elderly

T/CBDA 37-2020 机场航站楼建筑幕墙工程技术规程

1.总则；2.术语；3.基本规定；4. 材料；5. 设计；6. 加工制作；7. 安装施工；8. 工程验收；9. 维护及保养。

Technical specification for airport terminal curtain wall engineering