共找到 104 条与 外部输水系统 相关的标准,共 7 页
Covers the materials and application of tape coating systems in coating plants at fixed sites, using coating techniques and equipment as recommended by the tape coating manufacturer.
Tape Coating Systems for the Exterior of Steel Water Pipelines
This standard covers the material, application, and field procedure requirements for protective exterior coatings consisting of heat-shrinkable cross-linked polyolefin coatings and their application to special sections, connections, and fittings to be used in underground and underwater steel water pipelines.
Heat Shrinkable Crosslinked Polyolefin Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipelines
Covers the material, application, and curing of shop-applied, cement-mortar protective linings and coatings for steel water pipe and fittings, and field jointing of cement-mortar-lined-and-coated steel water pipe and fittings. Single copy price: $5.00 Order from: John Wilber, AWWA Send comments (with copy to BSR) to: Same
Cement-Mortar Protective Lining and Coating for Steel Water Pipe - 4 in (100 mm) and Larger - Shop Applied
Covers rubber-gasket joints of the following types for ductile-iron pressure pipe and ductile-iron and gray-iron fittings, valves, hydrants, and other appurtenances for water supply service.
Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings
The document lays down the dimensions, masses, materials and further technical requirements for steel filter pipes for drilled wells used for water catchment. The technical details are meant for nominal pipe diameters ND 100 to ND 500. A special equipment is the tension proof socket joint to be produced by a flexible shearing bar.
Steel filter pipes for drilled wells - Part 4: With tension proof socket joint; DN 100 to DN 500
Applies to the storage of water outside buildings.
Water supply - Requirements for systems and components for the storage of water
The document defines the dimensions, materials, and requirements of coverings for wells and other construction of water supply systems.
Coverings for wells, spring water chambers and other water supply construction - Principles for construction
This standard defines methods to be used in the structural design of buried prestressed concrete cylinder pipe (PCCP) under internal pressure. These methods are provided for the design of pipe subjected to the effects of working, transient, and field-test load and internal pressure combinations.
Design of Prestressed Concrete Cylinder Pipe
1.1 This guide covers procedures that are specifically related to permanent decommissioning (closure) of the following as applied to environmental activities. It is intended for use where solid or hazardous materials or wastes are found, or where conditions occur requiring the need for decommissioning. The following devices are considered in this guide: 1.1.1 A borehole used for geoenvironmental purposes (see Note 1), 1.1.2 Monitoring wells, 1.1.3 Observation wells, 1.1.4 Injection wells (see Note 2), 1.1.5 Piezometers, 1.1.6 Wells used for the extraction of contaminated groundwater, the removal of floating or submerged materials other than water such as gasoline or tetrachloroethylene, or other devices used for the extraction of soil gas, 1.1.7 A borehole used to construct a monitoring well, and 1.1.8 Any other vadose zone monitoring device. 1.2 Temporary decommissioning of the above is not covered in this guide.
Standard Guide for Decommissioning of Groundwater Wells, Vadose Zone Monitoring Devices, Boreholes, and Other Devices for Environmental Activities
The document contains general requirements for planning, construction, use and maintenance of water storage tanks.
Water supply - Requirements for systems and components for the storage of water; German version EN 1508:1998
The document contains general requirements for planning, construction, use and maintenance of water storage tanks.
Water supply - Requirements for systems and components for the storage of water
This standard specifies requirements for joints, made under field conditions, between adjacent preinsulated pipes and/or fittings in district heating networks.
Preinsulated bonded pipe systems for underground hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene (PE)
This document lays down the measurements, materials and requirements for steel wellheads. The wellheads serve as the upper end of drilled wells for raising of water.#,,#
Steel wellheads - ND 400 to ND 1200
The standard gives the basis and the methods for the calculation of the pipe diameters of drinking water installations in buildings and properties.
Drinking water supply systems; pipe sizing (DVGW code of practice)
Codes of practice for drinking water installations (TRWI); survey of standards and other codes of practice about materials, components and apparatus; DVGW code of practice
The standard describes the code of practice for planning and construction of drinking water systems in houses and properties as well as the components, apparatus and materials which are to use.#,,#
Drinking water supply systems; materials, components, appliances, design and installation (DVGW code of practice)
The standard settles the responsibilities for planning, construction and operation of drinking water installations, it defines important terms and gives the abbreviations and graphic symbols to use in drawings and plans.
Drinking water supply systems; general (DVGW code of practice)
The code applies to the design and execution of groundwater supply water systems which supply less than 10 properties. The code is applicable to the design and execution of new plants, to renewals, significant repair work or extension of existing plants. The code covers catchment plants, pumping systems, pump control plants, treatment plants, container plants and the corresponding installation pipes.
Dansk Ingenioerforening's Code of Practice for small non-common water supply systems
Plastics piping systems for non-pressure underground conveyance and storage of non-potable water — Boxes used for retention, detention, storage and transportation systems — Specifications for storm water boxes made of PE, PP and PVC-U
Steel filter pipes for drilled wells; with screw connection, nominal diameter 100 to 500
Steel Filter Pipes for Drilled Wells with Screwed Connection DN 100 to DN 500
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号