P95 施工机械设备综合 标准查询与下载

JB/T 10955-2010 摊铺机.计算机数据交换术语

本标准规定了摊铺机产品中控制和通讯系统中的计算机数据交换术语。 本标准适用于摊铺机计算机智能化和通讯系统的研制和应用。

Paver.Terminology used for computer data exchange

EN 500-1:2006+A1:2009 行动式道路工程机械.安全性.第1部分:一般要求

This part of EN 500 specifies the common safety requirements for mobile road construction machinery. The EN 500 series is applicable to mobile road construction machinery as listed in Annex A. When no specific standard exists, EN 500-1 applies. It specifies common requirements for the design and construction of mobile road construction machinery in order to protect workers from accidents and health hazards which could occur during operation, loading, transport and maintenance. Additional specific requirements for certain types of mobile road construction machinery are given in parts 2 to 4 and 6 of this standard. This part of this standard gives safety requirements for all types of mobile road construction machinery and shall be used in conjunction with one of the parts 2 to 4 and 6. These machine-specific parts do not repeat the requirements from part 1 but add to or replace the requirements for the type of mobile road construction machinery in question. Machine-specific requirements in parts 2 to 4 and 6 take precedence over the respective requirements of this standard. For types of mobile road construction machinery not dealt with in parts 2 to 4 and 6, EN 500-1 applies and if for those machinery additional derived risks may arise, these risks have to be taken into consideration. This European Standard deals with all significant hazards, hazardous situations and events relevant to mobile road construction machinery, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards as specified in Clause 4. This European Standard applies to machines which are manufactured after the date of publication of this European Standard by CEN. 1) For travelling on traffic roads, the national traffic regulations apply.

Mobile road construction machinery - Safety - Part 1: Common requirements

NF E58-250:2009 钻机.安全性

Drill rigs - Safety.

KS B 9704-2008 土方机械.履带式装载机与车轮式装载机的额定负荷工作

이 표준은 무한궤도식 로더 및 차륜식 로더의 성능 비교를 위한 정격 운전 하중에 대하여 규

Earth-moving machinery-Rated operating load for crawler and wheel loaders

KS B 9705-2008 土方机械.翻斗车挡泥板的容积测量

이 표준은 중덤프 흙받이로 운반하는 대표적인 적재물의 용적을 근사적으로 구하는 방법에 대하

Earth-moving machinery-Dumper bodies-Volumetric rating

KS B 9702-2008 工程机械用座椅振动传递特性的测试方法

이 표준은 건설 기계 중 무한궤도식 및 차륜식의 트랙터, 트랙터 셔블 및 자주식 스크레이퍼

Testing method of operator seat-transmitted vibration for construction machinery

KS B 9706-2008 土方机械.履带式拖拉机与履带式装载机的操纵装置

이 표준은 무한궤도식 트랙터 및 무한궤도식 로더의 운전자와 그 위치에 관하여 조종 장치의

Earth-moving machinery-Crawler tractors and crawler loaders-Operator’s controls

KS B 9703-2008 车轮式建设机械的回转半径测量方法

이 표준은 장비품을 탑재한 차륜식 건설 기계(이하 기계라 한다.)가 평탄 노면에서 회전할

Measurement of turning dimensions of wheeled construction machinery

ISO 6016:2008 土方机械.整个机器及其设备和部件的质量测量方法

Earth-moving machinery - Methods of measuring the masses of whole machines, their equipment and components

ISO 16714:2008 土方机械.可回收性和可修复性.术语和计算方法

This International Standard specifies a method, and defines related terms, for calculating the recyclability rate and the recoverability rate of earth-moving machinery as defined in ISO 6165, each expressed as a percentage by mass (mass fraction in percent) of the machine, which can potentially be recycled, reused or both (recyclability rate), or recovered, reused or both (recoverability rate). NOTE Remanufacturing is included in re-use The calculation can be performed by the machine manufacturer from the time when a machine is initially put on the market.

Earth-moving machinery - Recyclability and recoverability - Terminology and calculation method

ISO 3471:2008 土方机械.翻车保护结构.实验室试验和性能要求

This International Standard specifies performance requirements for metallic roll-over protective structures (ROPS) for earth-moving machinery, as well as a consistent and reproducible means of evaluating the compliance with these requirements by laboratory testing using static loading on a representative specimen. NOTE 1 The structure can also provide FOPS (falling-object protective structure) protection. This International Standard is applicable to ROPS intended for the following mobile machines with seated operator as defined in ISO 6165 and with a mass greater than or equal to 700 kg: -- dozer; -- loader; -- backhoe loader; -- dumper; -- pipelayer; -- tractor section (prime mover) of a combination machine (e.g. tractor scraper, articulated frame dumper); -- grader; -- landfill compactor; -- miler; -- trencher. This International Standard is not applicable to training seats or additional seats for operation of an attachment. NOTE 2 It is expected that reasonable crush protection for a seat-belted operator will be provided under at least the conditions of an initial forward velocity of 0 km/h to 16 km/h on a hard clay surface of 30° maximum slope in the direction of roll, and 360~ of roll about the longitudinal axis of the machine without loss of contact with the slope. NOTE 3 This International Standard can be used to provide guidance to the manufacturers of roll-over protective structures should it be decided to provide such protection for these or other machines for a particular application.

Earth-moving machinery - Roll-over protective structures - Laboratory tests and performance requirements

GXG 75-3-2008 通信建设工程施工机械、仪表台班费用定额

Quotas for construction machinery and instrument shift fees for communication construction projects

KS B ISO TR 25398:2008 土方机械.人体全身振动评估指南.利用国际机构组织和生产商合作测量数据

이 기술보고서는 고용주, 국가 당국과 KS B ISO 6165에서 정의된 운전자를 위한 일

Earth-moving machinery－Guidelines for assessment of exposure to whole-body vibration of ride-on machines－Use of harmonized data measured by international institutes, organizations and manufacturers

SAE J1119-2008 倾翻保护设备(ROPS)和坠落物体保护设备(FOPS)用钢制品

The purpose of this information report is to provide concepts for rational selection and application of materials for Rollover protective structures (ROPS) and Falling Object Protective Structures (FOPS) and to provide information about the properties that should be considered in selecting and utilizing material in protective structures. While other materials could conceivably be used successfully, this report is limited to a consideration of steel with discussion on its mechanical properties and processing characteristics. Emphasis is placed on the toughness aspect (ability to resist brittle fracture) as this property is of paramount importance to structure integrity. It is emphasized that specific values for material properties have relevance to performance only in conjunction with specific design consideration such as structure size or weld joint detail and location. Because there are many design-material systems which can be successfully employed to achieve the prescribed performance of protective structures, this report does not make categorical selection of steels.

Steel Products for Rollover Protective Structures (ROPS) and Falling Object Protective Structures (FOPS)

ISO 16001:2008 土方机械.危险探测设备和目视辅助设备.性能要求和试验

Earth-moving machinery - Hazard detection systems and visual aids - Performance requirements and tests

ANSI/ASME A120.1-2008 建筑物维护用动力升降工作台、移动梯和构架的安全要求

This Standard establishes safety requirements for powered platforms (scaffolds) for buildings where window cleaning and related services are accomplished by means of suspended equipment at heights in excess of 35 ft (11 m) above a safe surface (e. g. , grade, street, floor, or roof level). Additionally, this standard establishes safety requirements for permanent traveling ladders and gantries (TLG).

Safety Requirements for Powered Platforms and Traveling Ladders and Gantries for Building Maintenance

JIS A 8911:2007 土方机械.座椅安全带和座椅安全带固定器.性能要求和试验

この規格は，転倒時保護構造(ROPS) (JIS A 8910参照)をもつ土工機械及び横転時保護構造(TOPS) (JIS A 8921参照)をもつ土工機械の，運転員又は乗員を拘束する拘束装置ーシートベルト(以下,ベルトという。)及びその取付部に対する最低限の性能要求事項並びに試験方法について規定する。

Earth-moving machinery -- Seat belts and seat belt anchorages -- Performance requirements and tests

DIN 24118:2007 建筑设备和建筑材料机械.混凝土传送管道.尺寸

This standard applies for the dimensioning of concrete delivery lines, which are used for the conveying of concrete and other pumpable materials, e. g. mortar, screed.#,,#

Construction equipment and building material machinery - Concrete delivery pipelines - Dimensions and calculations

DIN 24117:2007 建筑设备和建筑材料机械.混凝土泵用配送杆.计算原则和稳定性

Construction equipment and building material machinery - Distributing mast for concrete pumps - Principles of calculation and stability

JIS A 8307:2006 土方机械.防护装置.定义和规范

この規格は, JIS A 8308に規定する土工機械の運転及び点検整備に関連して，機械的危険源，流体危険源及び熱的危険源から人を保護するために土工機械に取り付けるガードその他の保護方策の主要な用語を定義し，その要求事項及ぴ特性について規定する。

Earth-moving machinery -- Guards -- Definitions and requirements