Q34 工业技术玻璃 标准查询与下载

KS L 2410-2006 碳酸饮料玻璃瓶

이 규격은 내용물의 압력이 20 ℃에서 0.49 MPa(게이지 압력) 이하인 탄산 음료용

Carbonated beverage bottles

SAE AMS7727E-2006 低膨胀玻璃密封铁镍钴合金棒材和锻材53Fe - 29Ni - 17Co

This specification covers an iron-nickel-cobalt alloy in the form of bars and forgings.

Iron-Nickel-Cobalt Alloy, Bars and Forgings, 53Fe - 29Ni - 17Co, Low Expansion, Glass Sealing

SAE AMS7728H-2006 低膨胀玻璃密封退火铁镍钴合金片材、带材和板材53Fe - 29Ni - 17Co

This specification covers an iron-nickel-cobalt alloy in the form of sheet, strip, and plate.

Iron-Nickel-Cobalt Alloy, Sheet, Strip, and Plate, 53Fe - 29Ni - 17Co, Low Expansion Glass Sealing, Annealed

SAE AMS7726G-2006 低膨胀玻璃密封退火铁镍钴合金线材53Fe - 29Ni - 17Co

This specification covers a low-expansion iron-nickel-cobalt alloy in the form of wire.

Iron-Nickel-Cobalt Alloy, Wire, 53Fe - 29Ni - 17Co, Low Expansion, Glass Sealing, Annealed

JC/T 994-2006 微晶玻璃陶瓷复合砖

本标准规定了微晶玻璃陶瓷复合砖的术语和定义、分类、技术要求、试验方法、检验规则、标志、使用说明书、包装、运输及贮存。 本标准适用于建筑物内、外墙及地面装饰用微晶玻璃陶瓷复合砖。

Glass-ceramincs & Ceramics Combined Tile

NF S10-019/A1:2006 块状和预先成形的光学玻璃原材料.气泡和其他杂质.试验方法和分类

Raw optical glass in bulk and preshaped forms - Bubbles and other inclusions - Test method and classification.

ISO 14368-1:2000/cor 1:2006 无机和蓝宝石表玻璃.第1部分:尺寸和公差.技术勘误1

This standard is Mineral and sapphire watch-glasses - Part 1: Dimensions and tolerances; Technical Corrigendum 1

Mineral and sapphire watch-glasses - Part 1: Dimensions and tolerances; Technical Corrigendum 1

ASTM C1464-06 弯曲玻璃的标准规范

1.1 This specification covers the requirements for bent glass used in general building construction, furniture, display, and various other non-automotive applications.1.2 The dimensional values, stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only.The following safety hazards caveat pertains only to the test method portion, Section , of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bent Glass

ASTM C1464-06(2011) 弯曲玻璃的标准规格

1.1 This specification covers the requirements for bent glass used in general building construction, furniture, display, and various other non-automotive applications. 1.2 The dimensional values, stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bent Glass

SANS 20043:2005 关于安全玻璃材料及其在车辆上安装的批准的统一规定

Applies to safety glazing materials intended for installation as windscreens or other panes, or as partitioning, on power-driven vehicles and their trailers, and to the fitting thereof, to the exclusion, however, of glazing for lighting and light-signall

Uniform provisions concerning the approval of safety glazing materials and their installation on vehicles

SJ/T 3231-2005 低熔焊接玻璃粉

本标准规定了彩色显像管、彩色显示管及其它电子器件封接用低熔焊接玻璃粉的技术要求、检验规则和检验方法，以及标志、包装、运输、贮存。 本标准适用于彩色显像管、彩色显示管及其它电子器件用低熔焊接玻璃粉（简称低玻粉）。

Frit glass powder

JIS R 3205:2005 夹层玻璃

この規格は，主として建築及び船舶の窓，家具などに使用する合わせガラスについて規定する。

Laminated glass

DIN 7080:2005 低温范围内无限制的硼硅酸盐玻璃制抗压圆形视孔玻璃

The document is applicable to thermally prestressed circular sight glasses of borosilicate glass which can be subjected to permanent liquid or gas pressure on one side at temperatures up 280 ? Under specifies conditions, application up tp 300 ?is practicable (permitted).#,,#

Pressure resistant circular sight glasses of borosilicate glass without limitation in the range of low temperature

SANS 1472:2005 机动车辆用塑料安全玻璃材料

Covers requirements for plastics safety glazing materials for use on category M, N and O motor vehicles, excluding the windscreens of category M or N motor vehicles. Does not cover instrument dial windows, rear-view mirrors, light covers, bullet-resistan

Plastics safety glazing materials for motor vehicles

JC 981-2005 居室用玻璃台盆、台面

本标准规定了玻璃台盆、台面的分类、技术要求、试验方法、检验规则及标志、包装、运输、贮存等要求。 本标准适用于居室用玻璃台盆、台面。类似产品可参照本标准。

Household glass-washbowl and tabletop

ASTM E2269-05 用气相色谱法测定密封绝缘玻璃组件中氩浓度的标准试验方法

1.1 This test method covers procedures for using gas chromatographs to determine the concentration of argon gas in the space between the panes of sealed insulating glass.1.2 This test method is not applicable to insulating glass units containing open capillary/breather tubes.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units using Gas Chromatography

ASTM E2461-05 航线控制塔操作室玻璃厚度测定标准实施规范

1.1 This practice covers the determination of the thickness of glass installed in airport traffic control towers (ATCT) to resist a specified design loading with a selected probability of breakage less than or equal to either 1 lite per 1000 or 4 lites per 1000 at the first occurrence of the design wind loading.1.2 The procedures apply to common outward sloping cab glass designs for which the specified loads do not exceed 10 kPa (210 psf). 1.3 The procedures assume control tower cab glass has an aspect ratio no greater than 2.1.4 The procedures assume control tower cab glass has an area no less than 1.86 square metres (20 square feet).1.5 The procedures apply only to annealed monolithic, annealed laminated, or annealed insulating glass having a rectangular or trapezoidal shape. 1.6 The use of the procedures assumes the following:1.6.1 Annealed monolithic and annealed laminated glass installed in ATCTs shall have continuous lateral support along two parallel edges, along any three edges, or along all four edges; 1.6.2 Insulating glass shall have continuous lateral support along all four edges; and1.6.3 Supported glass edges are simply supported and free to slip in plane.1.7 The procedures do not apply to any form of wired, patterned, etched, sandblasted, or glass types with surface treatments that reduce the glass strength.1.8 The procedures do not apply to any form of heat treated glass, chemically strengthened glass, or any type of glass with surface treatments intended to increase the glass strength. 1.9 The procedures address the determination of thickness and construction type to resist a specified design wind load at a selected probability of breakage. The final glass thickness and construction determined also depends upon a variety of other factors (see ).1.10 These procedures do not address blast loading on glass.1.11 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Practice for Determining the Thickness of Glass in Airport Traffic Control Tower Cabs

ASTM E2461-05(2011) 测定机场交通控制塔工作间玻璃厚度的标准操作规程

1.1 This practice covers the determination of the thickness of glass installed in airport traffic control towers (ATCT) to resist a specified design loading with a selected probability of breakage less than or equal to either 1 lite per 1000 or 4 lites per 1000 at the first occurrence of the design wind loading.1.2 The procedures apply to common outward sloping cab glass designs for which the specified loads do not exceed 10 kPa (210 psf). 1.3 The procedures assume control tower cab glass has an aspect ratio no greater than 2.1.4 The procedures assume control tower cab glass has an area no less than 1.86 square metres (20 square feet).1.5 The procedures apply only to annealed monolithic, annealed laminated, or annealed insulating glass having a rectangular or trapezoidal shape. 1.6 The use of the procedures assumes the following:1.6.1 Annealed monolithic and annealed laminated glass installed in ATCTs shall have continuous lateral support along two parallel edges, along any three edges, or along all four edges; 1.6.2 Insulating glass shall have continuous lateral support along all four edges; and1.6.3 Supported glass edges are simply supported and free to slip in plane.1.7 The procedures do not apply to any form of wired, patterned, etched, sandblasted, or glass types with surface treatments that reduce the glass strength.1.8 The procedures do not apply to any form of heat treated glass, chemically strengthened glass, or any type of glass with surface treatments intended to increase the glass strength. 1.9 The procedures address the determination of thickness and construction type to resist a specified design wind load at a selected probability of breakage. The final glass thickness and construction determined also depends upon a variety of other factors (see ).1.10 These procedures do not address blast loading on glass.1.11 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Practice for Determining the Thickness of Glass in Airport Traffic Control Tower Cabs

ASTM F1915-05(2012) 拘留设施用玻璃窗的标准试验方法

The predictable and reliable performance of detention glazing used in detention and correctional facilities is a major concern. These test methods aid in assigning a level of physical security to glazing used in window and door assemblies based upon objective tests which can be consistently duplicated. These test methods identify four security grades, corresponding to the four security grades established in Test Methods F1450. The intent is to establish a comparable level of performance for opening assemblies which incorporate detention glazing in conjunction with window and door assemblies. Test methods for detention glazing differ in sequencing a variety of attack tools and temperatures. These test methods evaluate the resistance of detention glazing to attacks using blunt and sharp impact devices and fire. These test methods evaluate the performance of glazing in hot and cold environments. These test methods do not provide a measure of the resistance or performance of glazing subjected to attack by ballistics, chemical agents, explosives or other extreme methods of attack. Where such elements are a factor, consult the manufacturer. The primary purpose of these test methods is to approximate the levels of abuse and operating conditions to which detention glazing is subjected in detention and correctional institutions. The desired result of these test methods is to provide a measure of assurance of protection to the correctional personnel, public, and inmates. Detention and correctional facility administrative staff are encouraged to provide adequate training, supervision, and preventative maintenance programs to enable detention glazing assemblies to function as intended.1.1 These test methods, including a fire test response method, cover the apparatus, procedures, and acceptance conditions for evaluating the normal operational performance and the performance characteristics under assault conditions of detention glazing used in window and door assemblies in detention and correctional facilities; thus, these test methods only give an indication of the performance characteristics of detention glazing in actual service. Such variables as installation and maintenance conditions are not considered except as otherwise included in this test method. 1.2 It is the intent of these test methods to help ensure that detention glazing performs at or above minimum acceptable levels to restrict inmate passage to unauthorized areas, to confine inmates, to delay and frustrate escape attempts and to resist vandalism. 1.3 Tools defined in these test methods are representative of similar tools or materials, which may become available to inmates within the secure perimeter of detention and correctional facilities, and which could be used to inflict similar product damage. 1.4 These test methods should not be used to establish or confirm the absolute prevention of forced entries or exits. These test methods define five factors (tool, temperature, techniques, time, and number of impacts) used to determine resistance to defined attacks. 1.5 The values stated in inch-pound units are to be regarded as the standard. The SI values in stated parentheses are for information only. 1.6 In these test methods, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from these test methods to predict changes in the physical attack, or fire-test-response characteristics measured, or both; therefore, the results are valid only for the physical attack, or fire-test-exposure conditions, or both, described in these test methods. 1.7 This sta......

Standard Test Methods for Glazing for Detention Facilities

BS 7376:2004 工作台或手推车结构中使用的玻璃.规范

This British Standard specifies requirements to ensure reasonable safety of tables or trolleys which incorporate an area of flat glass >0.02 m.

Inclusion of glass in the construction of tables and trolleys - Specification