S33 走行部分 标准查询与下载

GOST R 53077-2008 轨道交通.设计和测试转向构架结构的规范

Railway applications. Rules of designing and testing the bogie frame structures

SANS 10354:2007 地下铁道的从动和非从动轮辐的安全使用

Specifies the technical aspects relating to the design, construction, installation, maintenance and safe usage of underground railway driven and non-driven wheel sets and associated equipment. Is applicable to wheel sets used on underground railway track

The safe application of underground railway driven and non-driven wheel sets

TB/T 3162.3-2007 铁道车辆停车防溜装置 第3部分:防溜铁鞋(止轮器)

本部分规定了防溜铁鞋(止轮器)的术语和定义、技术要求、试验方法、检验规则等。 本部分适用于采用铸钢和钢板焊接成型的防溜铁鞋(止轮器)的设计、生产、检验、使用和管理。适用于机车车辆在静止状态下的防溜防护。

Railway car anti-sliding device for stopping- Part 3: Braking shoe for loose protection

TB/T 3154-2007 机车车辆车轮和轮箍伤损代码

本标准规定了在役铁道机车车辆车轮、轮箍伤损编码规则、代码结构，给出了编码示例及主要车轮轮箍伤损名称、代码、伤损描述、原因及形貌示例。 本标准适用于在役铁道机车车辆车轮、轮箍（以下简称车轮、轮箍）伤损分析、判定及信息处理。

Damage codes of wheel and tyre for locomotive and vehicle

TB/T 3162.1-2007 铁道车辆停车防溜装置 第1部分:内撑式停车防溜器

本部分规定了用于铁路线路的内撑式停车防溜器的定义和术语、产品分类及型号命名、要求及参数、试验方法、检验规则、标志、包装、运输和储存。 本部分适用铁路站线、段管线、岔线及特别用途线等使用的内撑式停车防溜器的设计、制造、检验和使用。

Railway car anti-sliding device for stopping- Part 1: Inner-support anti-sliding device

TB/T 2208-2007 机车、动车用柴油机零部件曲轴扭振减振器

本标准规定了机车、动车用柴油机曲轴振减振器（以下简称减振器）的产品结构型式、技术要求、试验方法、检验规则、质量保证期、标志、包装、运输和贮存等。 本标准适用于机车、动车用柴油机曲轴扭振减振器。

Component partsof diesel engine for locomotive and car Crankshaft torsion vibration damper

TB/T 3162.2-2007 铁道车辆停车防溜装置 第2部分:停车防溜顶

TB/T 3162的本部分规定了停车防溜顶的术语和定义、分类与型号、技术要求、试验方法、检验规则、标志、包装、运输和储存。 本部分适用于铁路站线、段管线、岔线及特别用途线等使用的以液压油和弹性体为介质的停车防溜顶的设计、制造、检验和使用。机车防溜用停车防溜顶可参照使用。

Railway car anti-sliding device for stopping- Part 2: Piston arrester

DIN 27201-5 Berichtigung 1:2006 铁路车辆状态. 基本原则及生产技术. 第5部分: 铁路车辆车轮力及轮副垂直力检查, DIN 27201-5: 2006-05勘误表

This document determines principles for checking of wheel forces and vertical wheelset forces on maintenance of railway vehicles.

State of railway vehicles - Basic principles and production technology - Part 5: Checking of wheel forces and vertical wheelset forces of railway vehicles, Corrigenda to DIN 27201-5:2006-05

DIN 30052:2006 轨道车辆.轮副机构的命名

Rail vehicles - Designation for wheel set arrangement

TB/T 1463-2006 机车轮对组装技术条件

本标准规定了铁道机车新造动力轮对的注油压装、热装和压装组装的技术要求、验收规则、标志及保证等。 本标准适用于铁道机车新造动力轮对的整体车轮、轮心、轮箍车轮等与车轴的组装。

Technical specification for wheelsets assembly of railway locomotive

TB/T 3134-2006 机车、动车用驱动齿轮箱

本标准规定了机车、动车用驱动齿轮箱的技术要求、试验方法及检验规则、标识、包装、运输与贮存等。 本标准适用于200km/h及以上速度等级的机车、动车用封闭平行定轴传动的驱动齿轮箱，包括直齿、斜齿、人字齿及其组合的单级或多级渐开线圆柱齿轮驱动齿轮箱。其他速度等级的驱动齿轮箱可参照本标准执行。

Driving gear box for locomotive and rail car

DIN EN 13715:2006 轨道交通.轮副和转向轮.踏板轮廓

This document defines the tread profiles of wheels with diameter greater or equal to 330 mm used on vehicles running on European standard gauge track to fulfil interoperability requirements. These profiles apply to new wheels, whether free standing or assembled as wheelsets, as well as to wheels that require reprofiling during maintenance. Any profile that does not conform to this standard may only be used following agreement between the train operator and the infastructure manager.

Railway applications - Wheelsets and bogies - Wheels - Tread profile; English version of DIN EN 13715:2006-05

DIN 27201-5:2006 铁路车辆的状况.基本原理和产品技术.第5部分:铁路车辆的车轮压力和垂直车轮副压力的检查

This document determines principles for checking of wheel forces and vertical wheelset forces on maintenance of railway vehicles.

State of railway vehicles - Basic principles and production technology - Part 5: Checking of wheel forces and vertical wheelset forces of railway vehicles

TB/T 1959-2006 铁道货车摇枕、侧架静载荷及疲劳试验

本标准规定了铁道货车转向架用铸钢摇枕、侧架的静载荷试验、疲劳试验方法及评定准则。 本标准适用于铁道货车新造二轴转向架的铸钢摇枕及侧架。

Static load and fatigue test of bolster and side frame for railway freight car

TB/T 3012-2006 铁道货车铸钢摇枕、侧架技术条件

本标准规定了铁道货车用B级铸钢和C级铸钢摇枕、侧架的技术要求、试验方法、检验规则、标记及质量证明书等。 本标准适用于铁道货车用B级铸钢和C级铸钢摇枕、侧架的制造与检验。

Specification of cast steel bolster and side frame for railway freight car

DIN 27204-7:2006 铁路车辆的状况.行走机构.第7部分:行车机构和设备

The reached determinations in this document refer to the bogie with the forming building units.

State of railway vehicles - Running gear - Part 7: Bogie and equipment

BS EN 13715:2006+A1:2010 轨道交通.轮副和转向架.车轮.车轮踏板

Railway applications. Wheelsets and bogies. Wheels. Tread profile

BS EN 13715:2006 轨道交通.轮副和转向架.车轮.车轮踏板

This European Standard defines the tread profiles of wheels with a diameter greater than or equal to 330 mm used on vehicles running on European standard gauge track to fulfil interoperability requirements. These profiles apply to new wheels, whether free-standing or assembled as wheelsets, as well as to wheels that require reprofiling during maintenance. Any profile that does not conform to this standard shall only be used following agreement between the train operator and the infrastructure manager.

Railway applications. Wheelsets and bogies. Wheels. Wheels tread

DIN EN 13260:2006 轨道交通.轮副和转向架.轮副.产品要求

This European Standard specifies the characteristics of new wheelsets for use on European networks.

Railway applications - Wheelsets and bogies - Wheelsets - Product requirements; German version EN 13260:2003

DIN EN 13261:2006 轨道交通.轮副和转向架.轮轴.产品要求

This European Standard specifies the characteristics of axles for use on European networks.It defines characteristics of forged or rolled solid and hollow axles, made from vacuum-degassed steel grade EA1N (N for the normalized metallurgical condition, T for the quenched and tempered metallurgical condition) that is the most commonly used grade on European networks. For hollow axles, this standard applies only to those that are manufactured by machining of a hole in a forged or rolled solid axleIn addition, the particular characteristics for axles in grade EA1T1) and EA4T1) are given in annex A (normative).Two categories of axle are defined, category 1 and category 2. Generally, category 1 is chosen when the operational speed is higher than 200 km/h.This standard is applicable to axles that are designed in accordance with the requirements of EN 13103 and EN 13104 NOTE Different values for some characteristics may be agreed if a particular process of fabrication (e.g cold rolling, shot peening) has an influence on them.#,,#

Railway applications - Wheelsets and bogies - Axles - Product requirements; German version EN 13261:2003