T31 紧固件 标准查询与下载

SAE J238-2013 螺母和锥形弹簧垫圈组件

This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.

Nut and Conical Spring Washer Assemblies

SAE J483-2013 高顶和低顶(盲孔、帽形)六角螺母

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

High and Low Crown (Blind, Acorn) Hex Nuts

SAE J482-2013 六角高螺母

Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.

Hexagon High Nuts

SAE J1053M-2013 单齿节螺纹设计公制系列钢模压螺母

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE Standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.

Steel Stamped Nuts of One Pitch Thread Design Metric Series

SAE J1053-2013 单齿节螺纹设计公制系列钢模压螺母

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE Standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Steel Stamped Nuts of One Pitch Thread Design Inch Series

SAE J1102M-2013 公制车轮螺栓的机械和材料要求

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a. nonserrated shank bolts which are heat treated and b. serrated shank bolts which are case hardened.

Mechanical and Material Requirements for Metric Wheel Bolts

SAE J2485-2012 紧固件零件标准.机用螺钉螺母(公制和英制)

This SAE Part Standard covers selected machine screw nuts manufactured in accordance with American Society for Mechanical Engineers (ASME) dimensional standards. This document covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document. The purpose of this document is to assist the designer and other personnel in providing requirements and PINS for the most commonly used machine screw nuts. A PIN is normally required for all military applications

Fastener Part Standard - Machine Screw Nuts (Metric and Inch)

SAE J2337-2-2012 带ISO 261标准螺纹和O形密封的端口,螺柱端和插头用液压动力和高压连接件.第2部分:螺柱端要求,尺寸规格,设计和试验方法

This part of SAE J 2337 specifies dimensions, design, and performance requirements for eight connectors using a conical seal to insure leak proof performance with a design factor of 4 to 1. These connectors are intended for general and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These connectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuum to the working pressures shown in Table 1. Since many factors influence the pressure at which hydraulic systems will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that the required performance levels are met.

Connections for Fluid Power and High Pressure Use - Ports, Stud Ends, and Plugs with ISO 261 Threads and O-Rings Sealing Part 2: Stud End Requirements, Dimensions, Design and Test Methods

BS ISO 10597:2012 道路车辆.商用车辆用平面连接固定螺母.试验方法

Road vehicles. Flat attachment fixing nuts for commercial vehicles. Test methods

ISO 10597:2012 道路车辆.商用车辆用平面连接固定螺母.试验方法

This International Standard specifies test methods and performance requirements for ensuring proper wheel or rim assembly on road vehicles by means of hexagonal nuts with a flat seating captive washer used with 18 mm, 20 mm and 22 mm studs. It is applicable to commercial vehicles as defined in ISO 3833 and to those nuts as specified in ISO 7575. It is not applicable to fasteners for less common or special applications.

Road vehicles - Flat attachment fixing nuts for commercial vehicles - Test methods

SAE J995-2012 钢螺帽的机械和材料要求

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1 1/2 in., inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J 482 or ASME B18.2.2, except for machine screw nuts which ar not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 in, this may be done by the statement: "Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M."

Mechanical and Material Requirements for Steel Nuts

QC/T 861-2011 盲孔平头六角铆螺母

本标准规定了盲孔平头六角铆螺母的型式与尺寸、技术条件。 本标准适用于螺纹规格为M4～M10的汽车用盲孔平头六角铆螺母。

Flat head threaded tubular hexagon blind riveted nuts

QC/T 862-2011 B型方螺母座

本标准规定了B型方螺母座的型式与尺寸、技术条件。 本标准适用于螺母螺纹规格为M4～M12的汽车用B型方螺母座。

B type square nuts box

QC/T 877-2011 塑料用六角法兰面自攻螺钉

本标准规定了塑料用六角法兰面自攻螺钉的型式与尺寸、技术条件。 本标准适用于螺纹规格为NST3～NST6，与塑料螺母底孔或类似零件相配的汽车用六角法兰面自攻螺钉。

Hexagon flange head tapping screws for plastic

QC/T 878-2011 塑料用内六角花形盘头自攻螺钉

本标准规定了塑料用内六角花形盘头自攻螺钉的型式与尺寸、技术条件。 本标准适用于螺纹规格为NST3～NST6的与塑料螺母底孔或类似零件相配的内六角花形盘头自攻螺钉。

Hexalobular socket pan head tapping screws for plastic

QC/T 875-2011 内六角花形盘头自钻自攻螺钉

本标准规定了内六角花形盘头自钻自攻螺钉的型式与尺寸、技术条件。 本标准适用于螺纹规格为ST2.9～ST6.3的汽车用内六角花形盘头自钻自攻螺钉。

Hexalobular socket pan head self drilling screws with tapping screw thread

QC/T 879-2011 E型通孔式嵌装塑料螺母

本标准规定了E型通孔式嵌装塑料螺母的型式与尺寸、技术条件。 本标准适用于与NST4.5～NST6自攻螺钉螺纹相配的E型通孔式嵌装塑料螺母。

Plastic expansion nut with open end. Type E

QC/T 863-2011 焊接方螺母

本标准规定了焊接方螺母的型式与尺寸、技术条件。 本标准适用于螺纹规格为M4～M16和M10×1.25～M16×1.5，机械性能等级为8.8以下的螺栓配合使用的汽车用焊接方螺母。

Square weld nuts

QC/T 860-2011 焊接六角螺母

本标准规定了焊接六角螺母的型式与尺寸、技术条件。 本标准适用于螺纹规格为M4～M16和M10×1.25～M16×1.5，机械性能等级为8.8以下的螺栓配合使用的汽车用焊接六角螺母。

Hexagon weld nuts

QC/T 870-2011 双头螺柱.bm=1.25d

本标准规定了双头螺柱 bm=1.25d的型式与尺寸、技术条件。 本标准适用于旋入基体端螺纹为普通粗牙螺纹、过渡配合螺纹及普通细牙螺纹（螺纹规格大于M16），旋入螺母端螺纹为普通粗牙螺纹和普通细牙螺纹的汽车用双头螺柱。

Double end studs. bm=1.25d