27.220 热回收、绝热 标准查询与下载

ASTM C686-17(2023) 矿物纤维板条和毯子型绝缘材料的分型强度的标准试验方法

1.1 This test method covers evaluation of strength in tension on mineral fiber battand blanket-type insulation products. It is useful for determining the comparative tensile properties of these products, specimens of which cannot be held by the more conventional clamp-type grips. This is a quality control method, and the results shall not be used for design purposes. It is not suitable for board-type products. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Parting Strength of Mineral Fiber Batt- and Blanket-Type Insulation

ASTM C680-23 用计算机程序估算绝热平面、圆柱形和球形系统的热增益或热损失和表面温度的标准实施规程

1.1 This practice provides the algorithms and calculation methodologies for predicting the heat loss or gain and surface temperatures of certain thermal insulation systems that can attain one dimensional, steadyor quasi-steady-state heat transfer conditions in field operations. 1.2 This practice is based on the assumption that the thermal insulation systems can be well defined in rectangular, cylindrical or spherical coordinate systems and that the insulation systems are composed of homogeneous, uniformly dimensioned materials that reduce heat flow between two different temperature conditions. 1.3 Qualified personnel familiar with insulation-systems design and analysis should resolve the applicability of the methodologies to real systems. The range and quality of the physical and thermal property data of the materials comprising the thermal insulation system limit the calculation accuracy. Persons using this practice must have a knowledge of the practical application of heat transfer theory relating to thermal insulation materials and systems. 1.4 The computer program that can be generated from the algorithms and computational methodologies defined in this practice is described in Section 7 of this practice. The computer program is intended for flat slab, pipe and hollow sphere insulation systems. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Estimate of the Heat Gain or Loss and the Surface Temperatures of Insulated Flat, Cylindrical, and Spherical Systems by Use of Computer Programs

ASTM C1134-23 部分浸入后刚性绝热材料保水性的标准试验方法

1.1 This test method determines the amount of water retained (including surface water) by rigid block and board thermal insulations used in building construction applications after these materials have been partially immersed in liquid water for prescribed time intervals under isothermal conditions. This test method is intended to be used for the characterization of materials in the laboratory. It is not intended to simulate any particular environmental condition potentially encountered in building construction applications. 1.2 This test method does not address all the possible mechanisms of water intake and retention and related phenomena for rigid thermal insulations. It relates only to those conditions outlined in 1.1. Determination of moisture accumulation in thermal insulations due to complete immersion, water vapor transmission, internal condensation, freeze-thaw cycling, or a combination of these effects requires different test procedures. 1.3 Each partial immersion interval is followed by a brief free-drainage period. This test method does not address or attempt to quantify the drainage characteristics of materials. Therefore, results for materials with different internal structure and porosity, such as cellular materials and fibrous materials, are not necessarily directly comparable. Also, test results for specimens of different thickness are not necessarily directly comparable because of porosity effects. The surface characteristics of a material also affect drainage. It is possible that specimens with rough surfaces will retain more surface water than specimens with smooth surfaces, and that surface treatment during specimen preparation will affect water intake and retention. Therefore, it is not advisable to directly compare results for materials with different surface characteristics. 1.4 For most materials the size of the test specimens is small compared with the size of the products actually installed in the field. If the surface-to-volume ratios for the test specimens and the corresponding products are different, it is possible that the test results will be misleading. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Retention of Rigid Thermal Insulations Following Partial Immersion

GSO ASTM C1696:2023 工业隔热系统标准指南

  Scope is not provided for this standard

Standard Guide for Industrial Thermal Insulation Systems

GSO ASTM C795:2023 与奥氏体不锈钢接触使用的隔热标准规范

This specification covers non-metallic thermal insulation for use in contact with austenitic stainless steel piping and equipment. The material shall conform to the established requirements of the basic material specification. The physical and chemical requirements shall conform to the requirements of the basic material specification. Preproduction corrosion test and chemical analysis shall be performed to conform to the specified requirements.

Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel

23/30434502 DC BS ISO 6324 隔热产品 适用于工业应用的柔性微孔绝缘材料 规格

BS ISO 6324. Thermal insulation products. Flexible microporous insulation for industrial applications. Specification

T/SHDSGY 171-2022 蓄热式热氧化设备（RTO）余热利用技术规范

本文件规定了蓄热式热氧化设备（RTO）余热利用技术规范的术语和定义、原理、设备结构、要求、施工调试与验收。 蓄热式热氧化设备（RTO）的设计、制造、验收可参照使用。

Waste heat utilization of heat storage heat oxidation equipment (RTO)technical manual

ASTM C1289-22a 贴面硬质泡沫聚异氰尿酸酯隔热板的标准规范

1.1 This specification covers the general requirements for faced thermal insulation boards composed of rigid cellular polyisocyanurate surfaced with other materials. The insulation boards are intended for use at temperatures between −40 and 200°F (−40 and 93°C). This specification does not cover cryogenic applications. Consult the manufacturer for specific recommendations and properties in cryogenic conditions. For specific applications, the actual temperature limits shall be agreed upon by the manufacturer and the purchaser. 1.2 This standard is intended to apply to rigid cellular polyurethane-modified polyisocyanurate thermal insulation board products that are commercially acceptable as nonstructural panels useful in building construction. The term polyisocyanurate encompasses the term polyurethane. For engineering and design purposes, users should follow specific product information provided by board manufacturers regarding physical properties, system design considerations and installation recommendations. NOTE 1—See Appendix X1 for guidance on determining wind pressure resistance of panels when required for wall sheathing applications. 1.3 The use of thermal insulation materials covered by this specification is typically regulated by building codes, or other agencies that address fire performance. Where required, the fire performance of the material shall be addressed through standard fire test methods established by the appropriate governing documents. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 2—For conversion to metric units other than those contained in this standard, refer to IEEE/ASTM SI 10. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

T/QGCML 371-2022 乙二醇生产中热量回收再利用系统

本文件规定了乙二醇生产中热量回收再利用系统的术语和定义、构成及原理、技术要求、装置检验与维护。 本文件适用于乙二醇生产中热量回收再利用系统的生产和检验。

Heat Recovery and Reuse System in Ethylene Glycol Production

ASTM C667-17(2022) 环境温度空气以上管道操作和设备的预制纤维反射绝缘的标准规范

1.1 This specification covers the requirements for all metal prefabricated, reflective insulation systems for equipment and piping operating in air at temperatures above ambient. Typical applications are in nuclear power-generating plants and industrial plants. 1.2 Reflective insulation is thermal insulation that reduces radiant heat transfer across spaces by the use of surfaces of high reflectance and low emittance. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Prefabricated Reflective Insulation Systems for Equipment and Pipe Operating at Temperatures above Ambient Air

ISO 9288:2022 隔热.辐射传热.词汇

This document defines physical quantities and other terms in the field of thermal insulation relating to heat transfer by radiation.

Thermal insulation — Heat transfer by radiation — Vocabulary

ASTM C302-13(2022) 预制管覆盖型隔热材料密度和尺寸的标准试验方法

1.1 This test method covers the determination of the dimensions and density, after conditioning, of preformed pipe insulation. 1.1.1 Procedure A is applicable to sections of one-piece pipe covering or to sections of segmental pipe covering that can be joined together concentrically and measured as one-piece. 1.1.2 Procedure B is applicable to segmental pipe covering where each section of material is measured. 1.1.3 Procedure C is applicable to sections of one-piece pipe covering, such as soft foam or mineral wool materials, where it is possible to penetrate the material. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation

ASTM C585-22 管道标称尺寸的隔热内径和外径的标准实施规程

1.1 This practice is intended as a dimensional standard for preformed thermal insulation for pipes and tubing. 1.2 This practice covers insulation supplied in cylindrical sections and lists recommended single layer inner and outer diameters of insulation having nominal wall thicknesses from 1⁄2 to 5 in. (13 to 127 mm) to fit over standard sizes of pipe and tubing. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values stated in SI units are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing

ASTM C592-22a 矿物纤维毯绝缘和毯式管道绝缘（金属网覆盖）（工业型）的标准规范

1.1 This specification covers the composition, dimensions, and physical properties of mineral fiber (rock, slag, or glass) metal mesh covered and industrial type blanket and blankettype pipe insulation (typically on 24 in. (610 mm) diameters or larger)). Its use is for cooled surfaces at temperatures operating below ambient to 0°F (−18°C) and on heated surfaces on expansion joints to large diameter vessels and tanks operating at temperatures up to 1200°F (649°C). Specific applications outside the actual use temperatures shall be agreed upon between the manufacturer and purchaser. 1.2 For satisfactory performance, properly installed protective vapor retarders or barriers shall be used on below ambient temperature applications to reduce movement of moisture/ water vapor through or around the insulation towards the colder surface. Failure to use a vapor retarder can lead to insulation and system damage. Refer to Practice C921 to aid material selection. Although vapor retarder properties are not part of this specification, properties required in Specification C1136 are pertinent to applications or performance. 1.3 The orientation of the fibers within the blanket is primarily parallel to the heated surface. This specification does not cover fabricated pipe and tank wrap insulation where the insulation has been cut and fabricated to provide fiber orientation that is perpendicular to the heated surface. 1.4 This standard does not purport to provide the performance requirements of hourly-rated fire systems. Consult the manufacturer for the appropriate system. 1.5 See Supplementary Requirements for modifications to sections in this standard only when specified by purchaser in the contract or order from the U.S. Military specifications utilized by the U.S. Department of Defense, Department of the Navy, and the Naval Systems Command. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Mineral Fiber Blanket Insulation and Blanket-Type Pipe Insulation (Metal-Mesh Covered) (Industrial Type)

T/HPAAIA 41001-2022 工业管道用陶瓷棉绝热材料及其制品

本文件规定了工业管道用陶瓷棉绝热材料及其制品的分类和标记、要求、其他要求、检验规则、标志、包装、运输和贮存。

Ceramic fiber insulating materials and products for industrial pipelines

ASTM C592-22 矿物纤维毡绝缘和毡式管道绝缘（金属网覆盖）（工业型）的标准规范

Standard Specification for Mineral Fiber Blanket Insulation and Blanket-Type Pipe Insulation (Metal-Mesh Covered) (Industrial Type)

ASTM C1289-22 表面硬质多孔聚异氰脲酸酯隔热板标准规范

Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

T/CEC 592-2021 火力发电厂绝热工程质量管理规程

1.0.1 为规范火力发电厂热力设备和管道绝热工程质量，规范各单位质量管理行为，满足生产工艺要求，改善工作环境，降低绝热损失，提高机组经济效益，制定本规程。 1.0.2 本规程适用于火力发电厂设备及管道绝热工程质量管理。 1.0.3 绝热工程应推广采用电力建设新技术、新工艺、新流程、新装备、新材料（简称“五新技术”）。 1.0.4 绝热工程应制订“节约能源、节约场地、节约用水、节约材料和环境保护”的具体措施。 1.0.5 绝热工程在设计、采购、施工、验收阶段，应严格质量管控。 1.0.6 绝热材料的质量检测应由具备相关资质的检测机构进行。 1.0.7 绝热工程质量管理除应符合本规程外，尚应符合国家现行有关标准的规定。

Regulations on Quality Management of Thermal Power Plant Thermal Insulation Engineering

KS L ISO 8302-2021 绝热性 稳态热阻及相关性能的测定 防护热板装置

Thermal insulation－Determination of steady-state thermal resistance and related properties－Guarded hot plate apparatus

KS L ISO 8301-2021 绝热性 稳态热阻及相关性能的测定 热流量计装置

Thermal insulation－Determination of steady-state thermal resistance and related properties－Heat flow meter apparatus