55.040 包装材料和辅助物 标准查询与下载

ASTM D3078-02(2021)e1 用于通过气泡排放测定软包装中的泄漏的标准测试方法

1.1 This test method covers the determination of gross leaks in flexible packaging containing a headspace gas. Test sensitivity is limited to 1 × 10−5 atm cm3 /s (1 × 10−6 Pa m3 /s) or even less sensitive as indicated in a recent interlaboratory test (reported in Section 12). 1.2 Small leaks may not be detected by this procedure. Viscoelastic effects on the products, or entrapped air, become significant and prevent passage through small openings. Positive pressure inside the pouch after the vacuum is drawn may force the product to plug small leaks. The size of the leak that can be detected is dependent upon the products contained, the nature of the packaging material, and the test parameters selected. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Leaks in Flexible Packaging by Bubble Emission

ASTM F1306-21 柔性阻隔膜和层压板的缓慢渗透电阻的标准测试方法

1.1?This test method permits flexible barrier films and laminates to be characterized for slow rate penetration resistance to a driven probe. The test is performed at room temperature, by applying a biaxial stress at a single test velocity on the material until perforation occur

Standard Test Method for Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates

ASTM D3344-90(2021) 瓦楞纸板总蜡含量的标准试验方法

1.1 This test method covers the determination of the weight of wax that is present in a specimen of wax-treated corrugated paperboard. The test method is applicable to specimens that have been waxed by either impregnation (saturation) operations or coating operations, or combinations of such operations. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For precautionary statement, see 5.4 and 7.2. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Total Wax Content of Corrugated Paperboard

GOST 33214-2021 香料类化妆品生产的聚合与复合闭合方式 通用规格

Means of closing for perfumery cosmetic production. General specifications

GOST 32179-2021 关闭产品 安全、 标记和验收规则概述

Closure products. General on security, marking and acceptance rules

LST CEN/TS 17523-2020 邮政服务 可装箱物品的包装 将投递到消费者信箱中的小而轻的物品的包装特性

Postal services - Packaging for boxable items - Characteristics for packaging of small and light weight items to be delivered into the consumer's letterbox

KS T 1315-2020 阻塞测试方法

Testing method for blocking

KS T 1019-2020 瓦楞纤维板消费容器

Corrugated fibreboard consumer containers

KS T 1009-2020 缓冲包装设计方法通则

General rule for cushioning packaging design method

KS T 1017-2020 低温储存用瓦楞纤维板容器

Corrugated fiberboard containers for low temperature storage

ASTM D5414-95(2020) 负载均匀拉伸膜水平冲击性能评价标准试验方法

1.1 This test method is used to evaluate and compare the ability of stretch-wrap films to survive horizontal impacts in a laboratory simulation. 1.2 The test levels may be varied to represent the mode of shipping and handling used for the unit load under test. 1.3 The methodology of performing the controlled horizontal impacts is described in detail in Test Methods D4003. This test method will describe only sample preparation and evaluation in the special case of evaluating the performance of film for load unitizing. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluation of Horizontal Impact Performance of Load Unitizing Stretch Wrap Films

ASTM D5415-95(2020) 通过振动试验评估拉伸膜的载荷容纳性能的标准试验方法

1.1 This test method is used to evaluate and compare the ability of stretch-wrap films to contain unitized loads during shipping. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating Load Containment Performance of Stretch Wrap Films by Vibration Testing

ASTM D5416-95(2020) 通过振动试验评估拉伸膜的耐磨性的标准试验方法

1.1 This test method compares the abrasion resistance of similar types of stretch wrap films. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating Abrasion Resistance of Stretch Wrap Films by Vibration Testing

T/ZZB 1905-2020 烟用接装纸用电化铝烫印箔

本文件规定了烟用接装纸用电化铝烫印箔的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于以聚酯薄膜为基材，经离型、着色、真空镀铝、涂粘着剂而制成的烟用接装纸的烫印箔。

Hot stamping foil for cigarette tipping paper

T/ZZB 1885-2020 液体食品无菌包装用铝塑复合袋

本文件规定了液体食品无菌包装用铝塑复合袋（以下简称“复合袋”）的术语和定义、分类和结构、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于由塑料与铝箔或金属蒸镀膜等材料复合而成的，并配有灌装口等密封件，经过灭菌供液体食品无菌包装用的复合袋。

Aluminium-Plastic laminate bags for aseptic packaging of liquid food

ASTM F3004-13(2020) 使用机载超声波评估密封质量和完整性的标准测试方法

1.1 This standard method describes the technology and testing procedures that can be used to detect seal defects in the size range of 1 mm and characterize seal quality in a variety of packaging styles using airborne ultrasound technology. 1.2 This test method does not purport to be the only method for measurement of seal quality. 1.3 Heat seals and other package components can be tested in flexible, semi-rigid and rigid packages. Only the precision and bias for flexible package seals were evaluated in a recent ILS included in the method. The precision and bias for any specific package needs to be individually determined. 1.4 On-line, real time inspection of seals can be considered particularly in the L-Scan mode. 1.5 This method provides a non-destructive, quantitative, non-subjective approach to flexible package seal inspection. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluation of Seal Quality and Integrity Using Airborne Ultrasound

ASTM D5458-95(2020) 拉伸膜剥离粘贴标准试验方法

1.1 This test method measures cling between two layers of film, in both a stretched and unstretched condition. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Peel Cling of Stretch Wrap Film

ASTM D5459-95(2020) 机械方向弹性恢复和拉伸膜的永久变形和应力保持的标准测试方法

1.1 This test method covers the measurement of recovery from extension, permanent deformation, and stress retention of stretch wrap film. 1.2 Several levels of extension are included to ascertain the effect of both small and large extensions. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Machine Direction Elastic Recovery and Permanent Deformation and Stress Retention of Stretch Wrap Film

ASTM D3816/D3816M-96(2020) 压敏胶带水渗透率的标准试验方法

1.1 This test method provides one procedure for measuring the water penetration rate of 2-in. or wider pressure-sensitive tape. 1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be equivalent; therefore, each system must be used independently, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Penetration Rate of Pressure-Sensitive Tapes

ASTM D3889/D3889M-96(2020) 压敏胶带在低温下粘贴的标准试验方法

1.1 This test method covers one procedure for determining the adherence of pressure-sensitive tapes to a standard linerboard or other similar surface. 1.2 This test method provides for an attribute response (pass or fail) and does not yield numerical data on a variable or continuous scale. 1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently without combining values in any way. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Adherence to Linerboard of Pressure-Sensitive Tape at Low Temperature