55.040 包装材料和辅助物 标准查询与下载

KS T 1049-2019 用于印刷的压敏胶膜

Pressure sensitive adhesive films for printing

KS T 1032-2019 包装垫用发泡聚乙烯

Expanded polyethylene for packaging cushion

KS T 1029-2019 包装缓冲垫用发泡聚氨酯

Expanded polyurethane for packaging cushion

T/ZZB 1290-2019 医用透析原纸

本标准规定了医用透析原纸的基本要求、技术要求、试验方法、检验规则、包装、标志、运输和贮存及质量承诺。 本标准适用于最终低温灭菌或辐射灭菌的医疗器械包装材料用原纸。

Medical dialysis base paper

ASTM D3759/D3759M-05(2019) 压敏胶带的断裂强度和伸长率的标准测试方法

1.1 This test method covers the measurement of tensile strength at break (breaking strength) and stretch properties (elongation) for pressure-sensitive tapes and labels. It includes procedures for machine direction and cross direction, for high-strength filament reinforced backings and for high stretch backings. It also includes a procedure for obtaining force (“F” value) in conjunction with a specified elongation. These procedures employ a constant-rate-of-extension (CRE)-type testing machine. 1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; conversions between measurement systems must be conducted carefully. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Breaking Strength and Elongation of Pressure-Sensitive Tape

ASTM D3654/D3654M-06(2019) 压敏胶带的剪切粘附标准测试方法

1.1 This test method covers procedures for determining the ability of pressure-sensitive tapes and labels to remain adhered under constant load applied parallel to the surface of the tape and substrate. 1.1.1 Procedure A measures the shear adhesion when applied to a vertical standard steel panel. 1.1.2 Procedure B measures the shear adhesion when applied to vertical panel covered with NIST SRM 1810A standard fiberboard. 1.1.3 Procedure C measures the shear adhesion when applied to a vertical panel covered with a fiberboard as defined by Comite Europeen de Normalisation (CEN). 1.1.4 Procedure D measures shear adhesion when applied to a vertical panel covered with a fiberboard agreed upon by the buyer and seller. 1.1.5 Procedure E measures shear adhesion of filament reinforced tape when applied to a horizontal standard steel panel. 1.1.6 Procedure F measures shear adhesion of a filament reinforced tape when applied to a horizontal panel covered with NIST SRM 1810A standard fiberboard. 1.1.7 Procedure G measures the shear adhesion of a filament reinforced tape when applied to a horizontal panel covered with a standard fiberboard defined by CEN. 1.1.8 Procedure H measures the shear adhesion the same as Procedure A except the test is conducted at an elevated temperature and after a 10-min dwell time at the elevated temperature. 1.2 These procedures provide a means of assessing the uniformity of the adhesive of a given type of pressure-sensitive tape, usually tapes used for packaging applications. The assessment may be within a roll of tape, between rolls or production lots. 1.2.1 Variations in the tape backing and adhesive affect the response; therefore, these procedures cannot be used to pinpoint the specific cause(s) of nonuniformity. 1.2.2 This test method is intended to replace AFERA 4012, CEN 1943, and PSTC (see 7.2). 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems will result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes

ASTM D3833/D3833M-96(2019) 压敏胶带水汽传输的标准试验方法

1.1 This test method covers one procedure for measuring the water vapor transmission rate of pressure-sensitive tape. 1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Water Vapor Transmission of Pressure-Sensitive Tapes

ASTM E1870-11(2019) 聚合物包装膜的气味和味道转移的标准测试方法

1.1 This test method covers a recommended procedure for examining odor and taste properties of polymeric film intended for use as flexible packaging materials. This test method can be used for single (mono) layers, coextruded, and laminate materials. The focus of this test method is the evaluation of the film in terms of its perceived inherent odor and the transfer of package-related odors, or flavors, or both, to water and other model systems (bland food simulants). 1.2 This test method assumes testing of the films at a one-time point; shelf-life testing is not included. Please see Ref (1)2 for discussion of shelf-life testing. 1.3 This test method can provide sample preparation procedures and two methods of evaluation. The Film Performance Score Method allows for the comparison of any film sample to another. The Ranking Method allows for comparison of samples within a set. The preparation of samples is consistent regardless of the method of evaluation used. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film

ASTM F2467-06(2019) 运输应用中使用压力指示膜（PIF）测量静态密封压力的标准实施规程

1.1 This practice covers a standard means for measuring initial static sealing pressure in transportation applications. 1.2 It uses a pressure-indicating film (PIF) that will record the maximum load imprint of the seal-to-flange interfaces. The imprints will vary in intensity based on load across and along the interface. 1.3 These imprints can be used to determine if initial load on the gasket is adequate to attain a seal. These imprints may also indicate correct bolt torque sequence. These imprints may also be used to determine if the mating surface waviness or local flatness meets gasket requirements. Roughness is rarely found by PIFs because peak-to-peak wavelengths are too short. PIF is very good at finding waviness (peak to peak > 2.5 mm) and local flatness dips. PIFs provide an approximation of maximum pressures, and do not take into account relaxation of the joint after the torque sequence. Other methods involving dynamic measurement should be used if flange loading after relaxation is desired. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Measuring Static Sealing Pressure Using Pressure-Indicating Film (PIF) in Transportation Applications

ASTM F2468-05(2019) 指定用于运输应用的硅胶和密封剂的标准分类

1.1 This classification covers silicone adhesives and sealants intended for but not limited to sealing and retaining metallic and nonmetallic component assemblies in transportation applications. The materials cure to an elastomeric state by their specified cure system and mechanism. NOTE 1—The classification system may serve many of the needs of industries using silicone materials. This classification is subject to revision, as the need requires; therefore, the latest revision should always be used. 1.2 This classification is intended to be a means of classifying silicone materials. It is not intended for engineering design purposes. 1.3 It is not the intent of this classification to include pressure-sensitive or hot-melt adhesives. 1.4 In all cases in which the provisions of this classification system would conflict with the referenced ASTM standard for a particular method, the latter shall take precedence. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this classification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications

ASTM D5105-05(2019) 利用集中自然阳光对压敏胶带进行加速户外风化的标准实施规程

1.1 This practice covers one procedure for the exposure of pressure-sensitive tapes to an accelerated outdoor weathering environment. 1.2 This practice describes sample preparation and an accelerated outdoor environment to which it shall be exposed. It does not specify what observations or tests are to be performed on the material following exposure. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Performing Accelerated Outdoor Weathering of Pressure-Sensitive Tapes Using Concentrated Natural Sunlight

ASTM D4577-19 恒定负载下容器抗压性的标准试验方法

1.1 This test method is designed to determine the resistance of a shipping container to a vertically applied constant load for either a specified time or to failure. The test method may also be used for palletized or unitized load configurations. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Compression Resistance of a Container Under Constant Load

ASTM D3815/D3815M-05(2019) 用明火碳弧曝光装置加速压敏胶带风化的标准实施规程

1.1 This practice describes one environment for the exposure of pressure-sensitive tapes to a laboratory accelerated weathering environment. 1.2 This practice describes sample preparation and the laboratory-accelerated weathering environment to which it shall be exposed. It does not specify the length of time of the exposure nor what tests shall be performed on the material following the exposure. NOTE 1—Practice D6551/D6551M describes xenon-arc exposures of tapes. 1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently without combining values in any way. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus

JIS Z 1707:2019 食品包装用塑料薄膜总则

General rules of plastic films for food packaging

T/GDEIA 6-2019 站立式拉链膜袋

  站立式拉链膜袋 由PET、VMPET、PE、PET、AL、NY、CPP、PVC等塑料薄膜、铝箔、纸张等一种或多种材料复合，配套拉链，内装物充填后，在取出时，通过开口处的拉链，可反复封口、拉开，袋体能保持站立的膜袋。 站立式拉链膜袋的尺寸偏差 项目　偏差值 长度偏差 mm　袋长≤400　±3 　袋长≥400　±5 宽度偏差 mm　±2 折边宽度偏差 ％　±10 厚度偏差 ％　±10 热封宽度偏差 mm　封边宽度≤5　±1 　5＜封边宽度≤12　±2 　12＜封边宽度≤20　±3 　20＜封边宽度≤50　±4 注：长度指拉链封口到袋底的距离

Stand vertical zipper plastic film bag

T/TJWL 004-2018 食品冷链用蓄冷剂

5　技术要求 5.1　原材料 5.1.1　主要成分 包括：水、盐（氯化钠）、羧甲基纤维素钠、食品色素。 5.1.2　材质 采用上述原料成分组成的混合状液态材料，混合后性质稳定，不产生化学变化。 5.1.3　外观 蓄冷剂为清亮，半透明液体。 5.2　安全性 5.2.1　食品级安全指标的要求 5.2.1.1　生活饮用水的安全检测 符合GB 5749的要求 5.2.1.2　食用盐的安全要求 符合GB/T 5461的规定。 5.2.1.3　羧甲基纤维素钠的安全要求 符合GB 2760的规定。 5.2.1.4　食品色素的安全要求 符合GB 2760 的规定。 5.2.2　蓄冷剂的食品安全要求 依据 GB 15193.3进行蓄冷剂的急性经口毒性检测，符合规定。 5.3　使用性能 根据使用场景的要求，分为深冷的固态状、保冷的冰沙状、保鲜与保热的液态状。 5.4　理化指标允许偏差值 蓄冷剂理化指标及允许偏差见表1。 表1　蓄冷剂理化指标允许偏差值  标准指标 极限偏差　序号　温度特性 （相变温度）　相变潜热 （kj/kg）　盐含量　羧甲基纤维素钠含量 　1　上限值：-2.5℃　＞280　上限值：1.25%　上限值：0.20% 　　下限值：-1.5℃　　下限值：1.15%　下限值：0.15% 　2　上限值：-6.5℃　＞280　上限值：1.95%　上限值：0.20% 　　下限值：-5.5℃　　下限值：1.85%　下限值：0.15% 　3　上限值：-10.5℃　＞280　上限值：2.55%　上限值：0.20% 　　下限值：-9.5℃　　下限值：2.45%　下限值：0.15% 　4　上限值：-14.5℃　＞280　上限值：5.05%　上限值：0.20% 　　下限值：-13.5℃　　下限值：4.95%　下限值：0.15% 　5　上限值：-18.5℃　＞280　上限值：8.05%　上限值：0.20% 　　下限值：-17.5℃　　下限值：7.95%　下限值：0.15%

Refrigerant for food cold chain

T/TJWL 001-2018 食品冷链用塑料蓄冷包

5　技术要求 5.1　原材料 5.1.1　蓄冷剂 蓄冷剂应符合T/TJWL 004的要求。 5.1.2　塑料复合膜 包装采用的塑料复合膜由符合食品包装安全要求的PE和尼龙材料复合而成，材质理化性能符合GB/T 28117的规定，安全性能符合GB 4806.7的规定。所用多层共挤膜的外形尺寸，依据相关应用场景确定。 5.1.3　外观 食品冷链用塑料蓄冷包外表面干净整洁、无破损脏污，无漏液，内部为清亮液体，封口严实，尺寸符合要求。外包装标示清晰易读，若客户有特殊标示要求，依据客户要求进行。 5.2　机械物理性能 5.2.1　水蒸气透过量 塑料复合膜水蒸气透过量为≤15g/(㎡.24h）,符合GB/T 1037的要求。 5.2.2　拉断力和断裂标称应变 5.2.2.1　拉断力纵向为≥18Ｎ，横向为≥15Ｎ，符合GB/T 1040.3的要求。 5.2.2.2　断裂标称应变纵向为≥200％，横向为≥200％，符合GB/T 1040.3的要求。 5.2.3　耐压性能 施加61.2kg砝码压力（600N）的耐压试验后样品不破裂、渗漏，符合GB/T 21302的要求。 5.3　尺寸及偏差 常用规格尺寸及偏差要求见表1。 表1　尺寸及偏差  序号　产品名称代码　尺寸(长X宽)　极限偏差 1　Y XLB XXX XXX X X　225mm*140mm　±3% 2　Y XLB XXX XXX X X　140mm*140mm　±3% 3　Y XLB XXX XXX X X　140mm*110mm　±3% 5.4　蓄冷剂含量 常用蓄冷剂含量及偏差要求见表2。 表2　蓄冷剂含量及偏差 序号　产品名称代码　蓄冷液含量　极限偏差 1　Y XLB XXX XXX X X　500g　±5% 2　Y XLB XXX XXX X X　300g　±5% 3　Y XLB XXX XXX X X　150g　±5% 5.5　相变温度 常用相变温度要求见表3。 表3　相变温度分类  序号　产品名称代码　温度特性 1　YXLB XXX XXX A X　0℃ 2　YXLB XXX XXX C X　﹣4℃ 3　YXLB XXX XXX E X　﹣8℃ 4　YXLB XXX XXX G X　﹣12℃ 5　YXLB XXX XXX I X　﹣16℃ 5.6　颜色 蓄冷包常用颜色要求见表4. 表4　食品冷链用塑料蓄冷包颜色分类  序号　产品名称代码　颜色 1　YXLB XXX XXX X B　蓝色 2　YXLB XXX XXX X R　红色 3　YXLB XXX XXX X G　绿色 4　YXLB XXX XXX X Y　黄色 5　YXLB XXX XXX X X　其他 5.7　卫生指标 成品中的蓄冷剂应符合T/TJWL 004中卫生指标的要求，塑料复合膜应符合GB 4806.7的规定

Plastic Cold Storage Package for Food Cold Chain

T/TJWL 002-2018 食品冷链用塑料蓄冷板

5　技术要求 5.1　原材料 5.1.1　蓄冷剂 蓄冷剂应符合T/TJWL 004的要求。 5.1.2　塑料成型材料（塑料盒） 塑料成型材料采用符合食品包装要求的相关材料材质构成，材质的理化性能和安全性能符合GB 4806.7的规定，所用塑料成型材料（塑料盒）的外形尺寸，依据相关应用场景确定。 5.1.3　外观 食品冷链用塑料蓄冷板外表面干净整洁、无破损脏污，无漏液，内部为清亮液体，封口严实，尺寸符合要求。外包装标示清晰易读，若客户有特殊标示要求，依据客户要求进行。 5.2　机械物理性能 5.2.1　水蒸气透过量 塑料成型材料（塑料盒）水蒸气透过量为≤15g/(㎡.24h）,符合GB/T 1037的要求。 5.2.2　拉断力和断裂标称应变 5.2.2.1　拉断力纵向为≥18Ｎ，横向为≥15Ｎ，符合GB/T 1040.3的要求。 5.2.2.2　断裂标称应变纵向为≥200％，横向为≥200％，符合GB/T 1040.3的要求。 5.2.3　耐压性能 施加122.4kg砝码压力（1200N）的耐压试验后样品不破裂、渗漏，符合GB/T 21302的要求。 5.3　尺寸与偏差 食品冷链用塑料蓄冷板的规格尺寸与偏差见表1。 表1　食品冷链用塑料蓄冷板规格 序号　产品名称代码　尺寸（长×宽×厚）　极限偏差 1　H XLB 230 060 015 X X　230mm×60mm×15mm　±3% 5.4　蓄冷剂含量 食品冷链用塑料蓄冷板的蓄冷剂含量及偏差见表2。 表2　食品冷链用塑料蓄冷板蓄冷剂含量 序号　产品名称代码　蓄冷液含量　极限偏差 1　H XLB 230 060 015 X X　190ml　±5% 5.5　相变温度 食品冷链用塑料蓄冷板的相变温度见表3。 表3　食品冷链用塑料蓄冷板相变温度分类 序号　产品名称代码　温度特性 1　H XLB XXX XXX XXX A X　﹣0℃ 2　H XLB XXX XXX XXX C X　﹣4℃ 3　H XLB XXX XXX XXX E X　﹣8℃ 4　H XLB XXX XXX XXX G X　﹣12℃ 5　H XLB XXX XXX XXX I X　﹣16℃ 5.6　颜色 食品冷链用塑料蓄冷板的颜色分类见表4。 表4　食品冷链用塑料蓄冷板颜色分类 序号　产品名称代码　颜色 1　H XLB XXX XXX XXX X B　蓝色 2　H XLB XXX XXX XXX X R　红色 3　H XLB XXX XXX XXX X G　绿色 4　H XLB XXX XXX XXX X Y　黄色 5　H XLB XXX XXX XXX X X　其他 5.7　卫生指标 成品中的蓄冷剂应符合T/TJWL 004中卫生指标的要求，塑料复合膜应符合GB 4806.7的规定

Plastic cold board for food cold chain

T/ZZB 0797-2018 包装材料 聚烯烃交联型热收缩薄膜

本标准规定了包装材料聚烯烃交联型热收缩薄膜(以下简称“薄膜”)的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输与贮存及质量承诺等要求。 本标准适用于以聚烯烃热塑性树脂为主要原料，通过三层及三层以上共挤出膜坯后，经电子束辐照交联与双向拉伸工艺制得的，在特定使用条件下（热和外力的作用）具有热收缩功能的薄膜。

Packing material Polyolefin cross-linked shrink film

T/ZZB 0762-2018 烘焙原纸

本标准规定了烘焙原纸的产品分类、基本要求、技术要求、试验方法、检验规则、包装、标志、运输和贮存及质量承诺。 本标准适用于烘焙原纸。

Baking base paper