61.040 帽子、服饰品、衣扣 标准查询与下载

ASTM D2058-03(2022) 拉链饰面耐干洗性的标准试验方法

1.1 This test method covers the determination of the durability of the enamel or other decorative coating of zippers when subjected to drycleaning. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Durability of Finish of Zippers to Drycleaning

T/SDAQI 054-2021 纺织品 金属附件总铅和总镉含量的测定方法

本标准规定了纺织品中的金属附件总铅和总镉含量的测定方法。

Textiles - Determination of total content of lead and cadmium in metallic accessories

ASTM D4679-21 通用家用或美容师橡胶手套的标准规范

1.1 This specification covers requirements for gloves made of rubber-like latex, whether made of natural or synthetic materials, unsupported with or without a flock lining, intended for household, beautician use, or general use. 1.2 This specification is intended to serve as a guide to permit obtaining gloves of consistent performance. The safe and proper use of gloves is excluded from the scope of this specification. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Rubber General Purpose, Household or Beautician Gloves

T/JSTES 6-2021 双面数码印花丝绸围巾类产品

本文件规定了双面数码印花丝绸围巾类产品的术语和定义、要求、试验和检验方法、检验规则、标志、包装、运输和贮存。 本文件适用于主要原料为蚕丝、机织面料生产的双面数码印花丝绸围巾类产品。单面数码印花产品可参照执行。 本文件不适用于 14 周岁及以下婴幼儿、儿童用双面数码印花丝绸围巾类产品。

Double-sided digital printing silk scarfs

T/CTES 1048-2021 阻燃拉链

本文件规定了阻燃拉链的分类、要求、试验方法、检验规则、标志、包装、运输、贮存和使用准则。 本文件适用于在有明火、散发火花，或在有易燃物质并有轰燃风险场所使用的阻燃拉链的生产和检验。

Flame retardant zipper

T/ZZB 2532-2021 金属徽章

本文件规定了金属徽章（以下简称徽章）的产品分类和结构、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本文件适用于佩戴在人身上的徽章。 本文件不适用于婴幼儿、儿童用品。

Metal badges

T/ZZB 2445-2021 裙装用隐形拉链

本文件规定了裙装用隐形拉链的术语和定义、 基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于裙装用 3 号条装单头闭尾隐形拉链。 本文件不适用于年龄在 36 个月及以下的婴幼儿用拉链。

Invisible zipper for skirt

ASTM D6012-03(2021) 皮革耐（渗色）色斑转移性测定的标准试验方法

1.1 This test method2 covers the determination of whether leather bleeds (exudes coloring matter) when in intimate contact with wet surfaces, as indicated by staining produced on wet cloth in contact with the leather. This test method does not apply to wet blue. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Resistance of Leather to (Bleeding) Color Stain Transfer

KS K 0830-2021 塑料按钮耐冲击力耐久性的试验方法

Test method for durability of the plastic buttons to impact force

ASTM D7842/D7842M-12(2021) 大头钉和尖头扣件连接按钮的保持强度的标准试验方法

1.1 This test method covers the determination of the holding strength of a tack and prong fastener attached button using a tensile testing machine. 1.2 This test method is applicable to attached buttons in garments or to be attached to fabrics intended for use in apparel (see Annex A1). 1.3 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Holding Strength of Tack and Prong Fastener Attached Buttons

ASTM D3657-03(2021) 拉链尺寸的标准规范

1.1 This specification establishes standard dimensions for zippers of all materials for specified size designation; for equivalency, in inch-pound and metric units, of zipper length and length tolerances, of tape width and width tolerances, and of tape end lengths. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zipper Dimensions

ASTM D5170-98(2021) 钩环接触紧固件剥离强度的标准试验方法（“T”法）

1.1 This test method covers the measurement of the peel strength of hook and loop touch fasteners using a recording constant-rate-of-extension tensile testing machine (CRE). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Peel Strength (“T” Method) of Hook and Loop Touch Fasteners

T/ZZB 2096-2021 果实钮扣

本文件规定了果实钮扣的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本文件适用于以已加工的果实坯为原料制成的儿童用钮扣和其他类钮扣。 本文件不适用于婴幼儿用钮扣的生产。

Corozo buttons

T/TQA 0001-2021 邦典传统织造工艺规程

前言　I 1  范围　 2  规范性引用文件　 3  术语和定义　 4  原料　 5  织造工艺　 附录A（资料性）  织造工具　

Bangdian traditional weaving process regulations

T/TQA 0010-2021 叽玛传统织造工艺规程

前言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  氆氇原料　 5  织造工艺　

Jima Traditional Weaving Process Regulations

T/TQA 0011-2021 氆氇生产技术人员培训规范

前言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  基本要求　 5  培训内容 6  培训准备　 7  培训实施　 8  培训评估与改进　 9  培训档案管理　

Pulu production technician training specification

T/TQA 0013-2021 协玛传统织造工艺规程

前言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  氆氇原料　 5  织造工艺　

Xiema traditional weaving process regulations

T/TQA 0003-2021 布如通用技术要求

前言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  一般要求　 5  检验方法　 6  检验规则　 7  包装、标志、运输和贮存　

Fabric general technical requirements

T/TQA 0004-2021 布如传统织造工艺规程

前言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  氆氇原料　 5  织造工艺　

Cloth such as traditional weaving process regulations

T/TQA 0007-2021 藏靴（松巴）通用技术要求

前言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  产品分类　 5  一般要求　 6  检验方法　 7  检验规则　 8  包装、标志、运输和贮存　

General Technical Requirements for Tibetan Boots (Zomba)