87.020 涂料涂覆工艺 标准查询与下载

ISO 12944-1:2017 色漆和清漆.防护漆体系对钢结构的腐蚀防护.第1部分:总则

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 1: General introduction

ASTM D4228-05(2017) 镀层涂层在钢表面应用的标准实践

1.1 This practice provides a standard qualifying method for coating applicators to verify their proficiency and ability to attain the required quality for application of specified coatings to steel surfaces including those in safety-related areas in a nuclear facility. 1.2 Variations or simplifications of the practice set forth herein may be appropriate for special coating work such as maintenance or qualifications of equipment suppliers shop personnel. It is not the intent of this practice to mandate a singular basis for all qualifications. 1.3 Evaluation of the coating applicator being qualified in accordance with this practice, shall be by qualified agents as specified in 4.1. Reports shall be prepared as specified in Section 5, and certification as specified in Section 6. 1.4 It is the intent of this practice to judge only the ability of the coating applicator to apply specified coatings with the proper tools and equipment. 1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces

ASTM D4227-05(2017) 涂料涂料在混凝土表面应用的标准实践

1.1 This practice provides a standard qualifying method for coating applicators to verify their proficiency and ability to attain the required quality for application of specified coatings to concrete surfaces including those in safety-related areas in a nuclear facility. 1.2 Variations or simplifications of the practice set forth herein may be appropriate for special coating work such as maintenance. It is not the intent of this practice to mandate a singular basis for all qualifications. 1.3 Evaluation of the coating applicator being qualified in accordance with this practice, shall be by qualified agents as specified in 4.1. Reports shall be prepared as specified in Section 5, and qualification as specified in Section 6. 1.4 It is the intent of this practice to judge only the ability of the coating applicator to apply specified coatings with the proper tools and equipment. 1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces

ASTM D5066-91(2017) 汽车涂料喷涂生产条件下转移效率测定的标准试验方法&x2014；重量基准

1.1 This test method covers procedures for determination of the transfer efficiency (using a weight method) under production conditions for in-plant spray application of automotive paints as outlined in Section 18 of EPA 450/3-88-018. 1.2 The transfer efficiency is calculated from the weight of the paint solids sprayed and that deposited on the painted part. The recommended approach involves painting the part directly. Also described is an alternative approach for painting parts covered with aluminum foil. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 10.1.8.1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints—Weight Basis

ASTM D3260-01(2017) 工厂应用的透明涂层在挤压铝制品上的耐酸和耐砂性的标准测试方法

1.1 This test method covers the evaluation of the mortar and acid resistance of clear protective coating factory applied to extruded aluminum substrates. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Acid and Mortar Resistance of Factory-Applied Clear Coatings on Extruded Aluminum Products

ASTM D5324-16 水性建筑涂料测试标准指南

1.1 This guide covers the selection and use of procedures for testing water-borne coatings to be used on exterior, interior or both types of surfaces (Note 1). The properties that can be examined or, in some cases, the relevant test procedures are listed in Table 1 and Table 2. NOTE 1—The term “architectural coating” as used here combines the definition in Terminology D16 with that in the FSCT Paint/Coatings Dictionary, 2 as follows: “Organic coatings intended for on-site application to interior or exterior surfaces of residential, commercial, institutional, or industrial buildings, in contrast to industrial coatings. They are protective and decorative finishes applied at ambient temperatures. Often called Trade Sales Coatings.” NOTE 2—Architectural coatings that are designed to give better performance than most conventional coatings because they are tougher and more stain and abrasion resistant are covered by Guide D3730. 1.2 The types of organic coatings covered by this guide are as follows: (1) Type 1 Interior Latex Flat Wall Paints, (2) Type 2 Exterior Latex House Paints, (3) Type 3 Water-Borne Floor Paints, and (4) Type 4 Interior Latex Semigloss and Gloss Paints. 1.2.1 Each is intended for application by brushing, rolling, spraying or other means to the material appropriate for its type, which may include plaster, masonry, wallboard, wood, steel, previously painted surfaces, and other architectural substrates. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Testing Water-Borne Architectural Coatings

ASTM D6491-09(2016) 在干热试验中预应力预浸金属的耐老化性评价标准实践

1.1 This practice can be used to evaluate the resistance of a prestressed prepainted metal panel to cracking, or loss of adhesion, or both, after accelerated heat aging. Most coil coated products are formed and bent into specific shapes to produce a final product. These operations introduce stresses, which may be relieved by cracking of the coating after aging. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Evaluation of Aging Resistance of Prestressed Prepainted Metal In a Dry Heat Test

BS ISO 15741:2016 油漆和清漆.岸上和近海铺设的无腐蚀气体钢管道内侧的减小摩擦涂层

Paints and varnishes. Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases

ISO 15741:2016 涂料和清漆. 岸上和近海铺设的无腐蚀气体钢管道内侧的减小摩擦涂层

This document specifies reduirements and methods oftestfor liquid epoxypaints and internal coatings of such paints in steel pipes and fittings for the conveyance of non-corrosive gas. It also deals with the application ofthe paint. Other paints or paint Systems are not excluded provided they comply with the redquirements given in this document. The coating consists of one layen which is normally shop-applied on blastcleaned steel by airless Spray or other suitable Spraying techniques. The applied and cured paint film must be smooth to give the desired reduction in friction. Brush application is only used for Small repair jobs.

Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases

DB50/T 704-2016 陆上风力发电机组 钢结构零部件 防腐蚀保护技术规范

本标准适用于距离海岸线≥10km的陆地侧区域内机组钢结构零部件防腐蚀保护。 本标准适用于机组钢结构零部件的防腐蚀设计、施工、验收及运行维护，不适用于机组基础部分防腐蚀保护。

Technical specification for corrosion protection of steel structure components of onshore wind turbines

ASTM D3276-15 涂漆检查员用标准指南 (金属基质)

3.1 This guide is intended as a reference for those concerned with the inspection of industrial coating work. The requirements for inspection should be addressed in all protective coating and lining work specifications. This guide may be used by specification writers when selecting and establishing the inspection requirements for coating and lining specifications. A checklist for use by inspectors in the field is included in Appendix X1. 1.1 This guide is intended as an information aid to painting inspectors in carrying out their task efficiently. It includes the key elements of surface preparation, coatings application, and final approval for both field and shop work. The items should be selected that are pertinent to the specification of a particular job. Note 1: For additional helpful information, refer to the following documents: Manual of Coating Work for Light-Water Nuclear Power Plant Primary Containment and Other Safety-Related Facilities 2 New Concepts for Coating Protection of Steel Structures3 D16 Terminology for Paint, Related Coatings, Materials, and Applications 4 D4538 Terminology Relating to Protective Coatings and Lining Work for Power Generation Facilities 4 Steel Structures Painting Manual Vol 1 Good Painting Practice 6 Steel Structures Painting Manual Vol 2 Systems and Specifications 6 Manufacturers Specifications and Instructions (made available to the inspector for reference to special requirements for proper application) Safety Data Sheets (needed to ensure that personnel take necessary precautions in handling hazardous materials). Available from Materials manufacturer. 1.2 Certain industries or owners may require certified inspection personnel. See Guide D4537 for establishing procedures to certify inspectors for coatings work in nuclear facilities. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prio......

Standard Guide for Painting Inspectors (Metal Substrates)

ASTM D6577-15 工业防护覆层试验的标准指南

4.1 This guide is intended to provide assistance in selecting appropriate tests for evaluating the general performance level to be expected of a coating or coating system on a given substrate exposed to a given type of environment. Table 1 represents a listing of all the tests. 4.2 Surface preparation or cleanliness prior to application of the coating can be critical to the proper performance of the coating. 4.3 Results obtained in the tests cited in this guide may not be adequate for predicting coating service life of a specific coating system in a specific environmental exposure. A suitable control coating system of known performance in the service environment should be included in the testing for comparison. 1.1 This guide covers the selection and use of test methods and procedures for testing industrial protective coatings. Selection of the standards to be followed must be governed by experience and the requirements in each individual case, together with agreement between the supplier and the user. 1.2 This guide covers the testing of liquid coatings as applied on substrate by brushing, rolling, spraying, or other means appropriate to the coating and circumstance. Note 1: The term “industrial protective coating” as used in this guide is described in the scope of Subcommittee D01.461 as “paints applied to substrates on-site of structures and buildings, especially where subject to corrosive environments, as industrial, urban, and marine environments.” Note 2: Guides for testing other coating types, such as Guides D4712, D5146, D5324 or for surface preparation, coating application, such as Guide D3276, are available and should be used when it is applicable. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Testing Industrial Protective Coatings

GSO ISO 19840:2014 油漆和清漆 通过防护涂料系统对钢结构进行腐蚀防护 粗糙表面上干膜厚度的测量、验收标准

This International Standard specifies a procedure for the verification of dry-film thickness against nominal dry-film thickness on rough surfaces, including the adjustment of the instruments used, the definition of inspection areas, sampling plans, measurement methods and acceptance/rejection criteria. For the purposes of this standard, any specified thickness is taken to be nominal as defined in ISO 12944-5, and the dry-film thickness is the typical thickness above the peaks of the surface profile. The procedure described in this International Standard is based on the use of instruments of the permanent magnet, electromagnet and eddy current type. Instrument accuracy is verified both at zero and at a known thickness on a smooth surface and adjusted if necessary. Measurements taken on a coating on a roughened steel substrate will therefore be higher than the actual value above the peaks of the profile. The thickness of the dry film above the peaks of the profile is defined as the instrument reading minus an appropriate correction value. The dry-film thickness is obtained by using the appropriate correction value applied to readings based on adjustment on a smooth, flat steel surface. Where individual readings, based on adjustment on a smooth, flat steel surface without the use of correction values, are specified or agreed, it is important to recognize that this method does not conform with this International Standard. This standard is applicable if the nominal dry-film thickness is 40 µm or greater. NOTE If the nominal thickness is less than the surface roughness of the substrate, the uncertainty of the measurement will increase.

Paints and varnishes -- Corrosion protection of steel structures by protective paint systems -- Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces

GSO ISO 12944-5:2014 油漆和清漆 保护钢结构免受腐蚀的保护涂层系统 第5部分：保护涂层系统

This part of ISO 12944 describes the types of paint and paint system commonly used for corrosion protection of steel structures. It also provides guidance for the selection of paint systems available for different environments (see ISO 12944-2) and different surface preparation grades (see ISO 12944-4), and the durability grade to be expected (see ISO 12944-1). The durability of paint systems is classified in terms of low, medium and high.

Paints and varnishes -- Corrosion protection of steel structures by protective paint systems -- Part 5: Protective paint systems

KS M ISO 16276-2-2013(2018) 防护涂料体系对钢结构的腐蚀防护.涂层附着力/内聚力（断裂强度）的评定和验收标准.第2部分:横切试验和X-切试验

Corrosion protection of steel structures by protective paint systems ㅡ Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating ㅡ Part 2: Cross-cut testing an

KS M ISO 29601-2013(2018) 色漆和清漆 - 防腐蚀防护涂料系统 - 孔隙度的评价干膜

Paints and varnishes — Corrosion protection by protective paint systems — Assessment of porosity in a dry film

KS M ISO 16276-1-2013(2018) 防护涂料体系对钢结构的腐蚀防护第1部分:拉脱试验涂层附着力/内聚力（断裂强度）的评定和验收标准

Corrosion protection of steel structures by protective paint systems ㅡ Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating ㅡ Part 1: Pull-off testing

KS M ISO 29601:2013 涂料和清漆.用防护漆系统防腐蚀.干膜中孔隙率的评定

이 표준은 강철이나 기타 금속 소지에 도장한 모든 두께의 방식 도료 시스템에서 다공성을 측정하는절차에 대하여 규정한다. 이 표준에 기술된 절차들은 건조 도막 두께에 따라 선택하는 두 가지 유형의 시험 장치를 사용하는 방법에 기초한다. 이 표준에 기술된 절차들은 도료 시스템에서 전기 비전도성 부분의 시험에만 적용할 수 있다.규정된 시험방법은 주로 새로운 도막에 사용하지만 사용 중인 도막에도 사용할 수 있다. 사용 중인도막의 경우, 사용 중 도막과 접촉하는 물질이 도막에 침투했다는 점을 염두에 둔다.

Paints and varnishes — Corrosion protection by protective paint systems — Assessment of porosity in a dry film

KS M ISO 16276-2:2013 防护涂料系统对钢结构的腐蚀防护.涂层粘附/粘聚(断裂强度)的评估和验收标准.第2部分:横切测试和X切割测试

이 표준은 도막을 소지까지 직각 격자 무늬 형태(크로스컷) 또는 X형태(X컷)로 잘랐을 때 도장 시스템의 저항성 등급을 결정하는 절차에 대하여 규정한다.이 표준은 적절한 평가 척도를 통한 평가와 함께 크로스컷 또는 X컷 시험방법이 규정된 경우에만 적용할 수 있다.또한 이 표준은 적절한 장치를 규정하고 검사 영역, 샘플링 계획, 합격/불합격 기준을 정의한다.그러나 특별한 도장 시스템의 등급은 규정하지 않는다.

Corrosion protection of steel structures by protective paint systems ㅡ Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating ㅡ Part 2: Cross-cut testing and X-cut testing

KS M ISO 16276-1:2013 防护涂料系统对钢结构的腐蚀防护.涂层粘附/粘聚(断裂强度)的评估和验收标准.第1部分:剥离试验

이 표준은 두께가 10 mm 이상인 강철 소지에 도장한 방식 도료 도막의 파단 강도를 평가하는 절차에 대하여 규정한다. 이 표준에 기술한 절차는 다양한 유형의 박리 시험 장치를 사용하는 방법에 기초한다. 서로 다른 장치를 사용해 얻은 결과는 동일하지 않다.이 표준은 시험 장치 유형 및 장치 제조자와 함께 파단 강도의 값이 규정된 경우에만 적용할 수 있다. 일반적으로 이런 정보는 계약서에 명시된다.또한 이 표준은 적절한 장치를 규정하고 검사 영역, 샘플링 계획, 합격/불합격 기준을 정의한다.그러나 다양한 방식 도료 도막의 파단 강도 값은 제시하지 않는다.

Corrosion protection of steel structures by protective paint systems ㅡ Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating ㅡ Part 1: Pull-off testing