87.020 涂料涂覆工艺 标准查询与下载

T/ZZXJX 064-2021 水性建筑涂料涂饰工程施工与验收规程

前  言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 饰面基层　 5 材料　     5.1 一般规定　     5.2 原材料　     5.3 水性涂料性能　 6 设计　     6.1 一般规定　     6.2 装饰保温屋面　     6.3 装饰保温墙面　 7 施工准备　     7.1 一般规定　     7.2 施工工具　     7.3 作业条件　     7.4 作业平台　 8 施工工艺　     8.1 一般规定　     8.2 施工工艺　     8.3 文明施工　 9 验收　     9.1 一般规定　     9.2 主控项目　     9.3 一般项目　     9.4 验收　

Water-based architectural coatings finishing engineering construction and acceptance regulations

ASTM D2200-17(2021) 钢表面涂漆用图形表面处理标准和指南的使用标准实施规程

1.1 The visual surface preparation guides and standards consist of a series of color prints available as separate publications. Five different sets of photographs are described in this standard, designated as Method A (ISO/Swedish Standard2 ) and Methods B through E (SSPC Guides and Reference Photographs3 ). The methods differ in the depiction of the initial surface, in the definition and depiction of the cleaning conditions, and in the number of cleaning methods included. Because of these differences, the specifier should state which guide to use. 1.2 The colored visual surface preparation guides represent different conditions of hot-rolled carbon steel before and after surface preparation. Prior to cleaning, there are four rust grades, A to D, that cover the range from intact mill scale to 100 % rusted and pitted steel. The standards then depict the appearance of the initial conditions after cleaning by one or more methods (for example, dry abrasive blast cleaning) to various degrees of thoroughness. In addition, Method B includes three painted conditions that contain various degrees of deterioration. The Guide3 depicts these conditions after various degrees of dry abrasive blast cleaning. Method C includes four rust grades and three painted conditions that contain various degrees of deterioration. The Guide4 depicts these conditions after various degrees of hand and power tool cleaning. Method D includes two rust grades and four painted conditions that contain various degrees of deterioration. The Guide5 depicts these conditions after various degrees of water jetting, with three levels of flash rusting. Method E includes two rust grades. The Guide6 depicts these conditions after various degrees of wet abrasive blast cleaning, with three levels of flash rusting. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces

ASTM D3276-21 涂装检验员（金属基材）的标准指南

1.1 This guide is intended as an information aid to painting inspectors in carrying out their task efficiently. It includes the key elements of surface preparation, coatings application, and final approval for both field and shop work. The items should be selected that are pertinent to the specification of a particular job. NOTE 1—For additional helpful information, refer to the following documents: Manual of Coating Work for Light-Water Nuclear Power Plant Primary Containment and Other Safety-Related Facilities 2 New Concepts for Coating Protection of Steel Structures3 D16 Terminology for Paint, Related Coatings, Materials, and Applications4 D4538 Terminology Relating to Protective Coatings and Lining Work for Power Generation Facilities4 Steel Structures Painting Manual Vol 1 Good Painting Practice5 Steel Structures Painting Manual Vol 2 Systems and Specifications5 Manufacturers Specifications and Instructions (made available to the inspector for reference to special requirements for proper application) Safety Data Sheets (needed to ensure that personnel take necessary precautions in handling hazardous materials). Available from Materials manufacturer. 1.2 Certain industries or owners may require certified inspection personnel. See Guide D4537 for establishing procedures to certify inspectors for coatings work in nuclear facilities. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This guide is arranged in the following order: Section Referenced Documents 2 ASTM Standards 2.1 OSHA Standards 2.2 Steel Structures Painting Council Publications 2.3 International Standards Organization (ISO) 2.4 ASTM Adjuncts 2.6 Significance and Use 3 Preparation for Inspection 4 Surface Preparation Methods and Requirements 5 Surface Preparation 5.1 Pictorial Standard D2200 5.1.1 Factors Affecting Coating Performance 5.2 Cleanliness 5.2.1 Mill Scale 5.2.2 Surface Profile 5.2.3 Sharp Edges 5.2.4 Cleaning Procedures 5.3 Chemical Cleaning 5.3.1 Solvent Vapor Cleaning 5.3.1.1 Hand Tool Cleaning 5.3.2 Power Tool Cleaning 5.3.3 Power Tool Cleaning to Bare Metal 5.3.4 Commercial Grade Power Tool Cleaning 5.3.4.4 Blast Cleaning 5.3.5 Pressurized Water Cleaning 5.3.6 Cleaning and Preparation of Various Surfaces 5.4 Steel Surfaces 5.4.1 Galvanized Surfaces 5.4.2 Aluminum Surfaces 5.4.3 Precautions in Preparing Unpainted and Previously Painted Surfaces 5.4.4 Inspection of Surfaces Prior to Field Painting 5.5 New Construction 5.5.1 Maintenance Repainting 5.5.2 Coating Storage and Handling 6 Storage of Coating and Thinner 6.1 Mixing of Coatings 6.2 Thinning 6.3 Initial Samples 6.3.1 Thinning of Coating 6.3.2 Sampling of Thinned Coating 6.3.3 Heating of Coating 6.4 Weather Considerations 7 Drying 7.1 Low Temperature 7.2 High Temperature 7.3 Moisture 7.4 Wind 7.5 Coating Application 8 Residual Contaminants 8.1 Quality Assurance 8.2 Film Defects 8.2.1 Brush Application 8.3 Spray Application 8.4 1 This guide is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of Subcommittee D01.46 on Industrial Protective Coatings. Current edition approved Nov. 1, 2021. Published December 2021. Originally approved in 1973. Last previous edition approved in 2015 as D3276 – 15ɛ1 . DOI: 10.1520/D3276-21. 2 ASTM, 1979. 3 ASTM STP 841, ASTM, 1984. 4 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards volume information, refer to the standard’s Document Summary page on the ASTM website. 5 Available from Association for Materials Protection and Performance (AMPP), 15835 Park Ten Place, Houston, TX 77084, https://www.ampp.org. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 8QLYHUVLW\RI7RURQWR 8QLYHUVLW\RI7RURQWR SXUVXDQWWR/LFHQVH$JUHHPHQW1RIXUWKHUUHSURGXFWLRQVDXWKRUL]HG 'RZQORDGHGSULQWHGE\ &RS\ULJKWE\$670,QW O DOOULJKWVUHVHUYHG 7KX'HF*07 Roller Application 8.5 Miscellaneous Methods 8.6 Rate of Application 8.7 Additional Considerations 9 Ventilation 9.1 Shopcoat Repair 9.2 Painting Schedule 9.3 Film Integrity 9.4 Recoat Time 9.5 Coating System Failure 9.6 Inspection Equipment 10 General 10.1 Surface Profile Gages 10.1.1 Adhesion of Existing Coating 10.1.2 Portable Pull-Off Adhesion Testers 10.1.3 Field Inspection Equipment 10.2 Drying and Curing Times 10.2.1 Thermometers 10.2.1.1 Relative Humidity and Dew Point 10.2.1.2 Wet-Film Thickness Gages 10.2.2 Interchemical Gage 10.2.2.1 Notched Gage 10.2.2.2 Dry-Film Thickness Gages 10.2.3 Nondestructive Film Thickness Gages 10.2.3.1 Magnetic-Type Gages 10.2.3.2 Current-Type Gages 10.2.3.3 Destructive Thickness Gage 10.2.3.4 Holiday Detectors 10.2.4 Comparison of Surface Preparation Specifications Table 1 Comparison of Water Jetting Standards Table 2 Inspection Checklist Appendix X1 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Painting Inspectors (Metal Substrates)

T/SHHJ 000032-2021 建筑钢结构防腐涂料应用技术规程

涉及建筑钢结构防腐涂料涂装设计、施工和验收的技术要求

Technical specification for application of anti-corrosive coatings on building steel structures

PN-EN ISO 15741-2021-07 E 油漆和清漆 用于非腐蚀性气体的陆上和海上钢管内部的减摩涂层（ISO 15741:2016）

Paints and varnishes--Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases (ISO 15741:2016)

UNI EN ISO 15741:2021 油漆和清漆 用于非腐蚀性气体的陆上和海上钢管内部的减摩涂层

Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases

PN-EN ISO 12944-5-2020-03 P 色漆和清漆 防护漆体系对钢结构的腐蚀防护 第5部分：防护漆体系（ISO 12944-5:2019）

Paints and varnishes--Corrosion protection of steel structures by protective paint systems--Part 5: Protective paint systems (ISO 12944-5:2019)

T/GSTX 001-2021 公路隧道防护涂装技术规范

本标准规定了内陆公路隧道设施防护涂层的技术条件，包括防护涂层的分类、要求、试验方法、检验规则、安全、卫生和环境保护、验收。       本标准适用于内陆公路隧道设施防护涂层的初始涂装和修补涂装

Technical specification for road tunnel protective coating

SN EN ISO 15741:2021 油漆和清漆 用于非腐蚀性气体的陆上和海上钢管内部的减摩涂层（ISO 15741:2016）

Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases (ISO 15741:2016)

T/FWHX 002-2021 聚合物乳液建筑防水涂料

表1　物理力学性能 序号　试验项目　指标 　　Ⅰ　Ⅱ 1　拉伸强度，MPa ≥　1.0　1.5 2　断裂延伸率，% ≥　300 3　低温柔性，绕Φ10mm棒弯180°　-10℃，无裂纹　-20℃，无裂纹 4　不透水性，（0.3MPa，120min）　不透水 5　固体含量，% ≥　65 6　干燥时间，h　表干时间 ≤　4 　　实干时间 ≤　8 7　处理后的拉伸强度保持率，%　加热处理≥　80 　　碱处理≥　60 　　酸处理≥　40 　　人工气候老化处理a≥　-　80～150 8　处理后的断裂延伸率，%　加热处理≥　200 　　碱处理≥　200 　　酸处理≥　200 　　人工气候老化处理a≥　-　200 9　加热伸缩量，%　伸长≤　1.0 　　缩短≤　1.0 a仅用于外露使用产品。

Polymer Emulsion Architectural Waterproof Coatings

OENORM EN ISO 15741:2021 油漆和清漆 用于非腐蚀性气体的陆上和海上钢管内部的减摩涂层（ISO 15741:2016）

Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases (ISO 15741:2016)

T/FWHX 001-2021 非固化橡胶沥青防水涂料

6.2　物理力学性能 产品物理力学性能应符合表1的规定。 表1　物理力学性能 序号　项目　技术指标 1　闪点/℃　≥180 2　固含量/%　≥98 3　粘结性能　干燥基面　100%内聚破坏 　　潮湿基面　 4　延伸性/mm　≥15 5　低温柔性　-20℃，无断裂 6　耐热性/℃　90 　　无滑动、流淌、滴落 7　热老化 70℃, 168h　延伸性/mm　≥15 　　低温柔性　-15℃,无断裂 8　耐酸性（2%H2SO4溶液）　外观　无变化 　　延伸性/mm　≥15 　　质量变化　±2.0 9　耐碱性[0. 1%NaOH+饱和Ca(OH)2溶液]　外观　无变化 　　延伸性/mm　≥15 　　质量变化　±2.0 10　耐盐性(3%NaCI溶液)　外观　无变化 　　延伸性/mm　≥15 　　质量变化　±2.0 11　自愈性　无渗水 12　渗油性/张　≤2 13　应力松弛/%　无处理　≤35 　　热老化(70℃, 168 h)　 14　抗窜水性/ 0.6 MPa　无窜水 15　黏度/ mPa.s (130℃)　≤1500

Non-curing rubber bitumen waterproof coating

T/FWHX 003-2021 水乳型沥青防水涂料

乳型沥青防水涂料产品力学性能 序号　试验项目　指标 　　L　H 1　固体含量，% ≥　45 2　耐热度，℃　80±2　110±2 　　无流淌、滑动、滴落 3　不透水性　0.3MPa，120min无渗水 4　粘结强度，MPa ≥　0.30 5　表干时间 ≤　8 6　实干时间 ≤　24 7　低温柔性a，℃　标准条件　-15　0 　　碱处理　-10　5 　　酸处理　-10　5 　　紫外线处理　-10　5 8　断裂伸长率，%　标准条件　600 　　碱处理　600 　　酸处理　600 　　紫外线处理　600 a供需双方可以商定温度更低的低温柔度指标。

Water emulsion asphalt waterproof coating

LST EN ISO 15741:2021 油漆和清漆 用于非腐蚀性气体的陆上和海上钢管内部的减摩涂层（ISO 15741:2016）

Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases (ISO 15741:2016)

KS M ISO 12944-2-2021 色漆和清漆.防护漆系统对钢结构的腐蚀防护.第2部分:环境分类

Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 2: Classification of environments

KS M ISO 12944-1:2021 色漆和清漆.防护漆系统对钢结构的腐蚀防护.第1部分:概述

Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 1: General introduction

KS M ISO 12944-8:2021 色漆和清漆.防护漆系统对钢结构的腐蚀防护.第8部分:新工作和维护规范的制定

Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 8: Development of specifications for new work and maintenance

KS M ISO 12944-6-2021 色漆和清漆.防护漆系统对钢结构的腐蚀防护.第6部分:实验室性能试验方法

Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 6: Laboratory performance test methods

KS M ISO 12944-2:2021 色漆和清漆.防护漆系统对钢结构的腐蚀防护.第2部分:环境分类

Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 2: Classification of environments

KS M ISO 12944-3:2021 色漆和清漆.防护漆系统对钢结构的腐蚀防护.第3部分:设计考虑

Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 3: Design considerations