35.160 微处理机系统 标准查询与下载

DB34/T 2147-2014 便携式学习机

本标准规定了便携式学习机电脑的术语和定义、基本配置、要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于便携式学习机（以下简称学习机)。

portable learning machine

KS X 5019-2013 信息技术 微处理器系统 VICbus 板条箱间电缆总线

INFORMATION TECHNOLOGY - MICROPROCESSOR SYSTEMS - VICbus - INTER-CRATE CABLE BUS

GSO ISO 3792:2013 机器 功能键盘设计

Abstract Outlines the keyboard arrangement of adding machines. References: ISO 1092; 1093; 3244; 3791.

Adding machines -- Layout of function keyboard

IEC 100/2170/DTS:2013 IEC/TS 62700,版本1.0:便携式个人计算机的直流(DC)电源

IEC/TS 62700, Ed. 1.0: DC Power Supply for Portable Personal Computer

GSO ISO/IEC 15776:2013 运营商 VME64 规格

The VMEbus specification defines an interfacing system used to interconnect microprocessors, data storage, and peripheral control devices in a closely coupled hardware configuration

VME64bus - Specification

GSO ISO/IEC 15205:2013 Bus 芯片和单元互连总线

SBus is a high performance computer I/O interface for connecting integrated circuits and SBus Cards to a computer system motherboard. This standard defines the mechanical, electrical, environmental, and protocol requirements for the design of SBus Cards and the computer system motherboard that supports those cards

SBus - Chip and module interconnect bus

DS/EN 62623:2013 台式电脑和笔记本电脑 能量消耗的测量

This International Standard covers personal computing products. It applies to desktop and notebook computers as defined in 4.1 that are marketed as final products and that are hereafter referred to as the equipment under test (EUT) or product.This standar

Desktop and notebook computers - Measurement of energy consumption

EN 62623:2013 台式电脑和笔记本电脑 能量消耗的测量

IEC 62623:2012 covers personal computing products. It applies to desktop and notebook computers as defined in 4.1 that are marketed as final products and that are hereafter referred to as the equipment under test (EUT) or product. This standard specifies: - a test procedure to enable the measurement of the power and/or energy consumption in each of the EUT's power modes; - formulas for calculating the typical energy consumption (TEC) for a given period (normally annual); - a majority profile that should be used with this standard which enables conversion of average power into energy within the TEC formulas; - a system of categorisation enabling like for like comparisons of energy consumption between EUTs and a pre-defined format for the presentation of results. This standard does not set any pass/fail criteria for the EUTs. Users of the test results should define such criteria. Keywords: Power consumption, Desktop computer, Notebook computer

Desktop and notebook computers - Measurement of energy consumption

KS X 5030-2013 信息技术锛峂微处理器系统-Futurebus+TM, Profile M（military）

Information technology－Microprocessor systems -Futurebus+TM, Profile M(military)

KS X 5018-2013 微处理器的 Futurebus+ 逻辑协议规范

INFORMATION TECHNOLOGY - MICROPROCESSOR SYSTEMS - FUTUREBUS＋ - LOGICAL PROTOCOL SPECIFICATION

DB41/T 726-2011 计算机信息系统（场地）防雷安全检测技术规范

Computer information system (site) lightning protection safety inspection technical specification

ASME VV 10.1-2012 计算固体力学中验证和批准概念的例证

This Standard describes a simple example of verification and validation (V&V) to illustrate some of the key concepts and procedures presented in V&V 10. The example is an elastic, tapered, cantilever, box beam under nonuniform static loading. The validation problem entails a uniform loading over half the length of the beam. The response of interest is the tip deflection. The validation test plan and the metrics and accuracy requirements for comparing the calculated responses with measurements are specified in theV&VPlan, which is developed in the first phase of the V&V program. In setting validation requirements and establishing a budget for the V&V program, the V&V Plan considers the level of risk in using the model for its intended purpose. Successfully meeting the V&V requirements means that the computational model for the tapered beam has been validated for the intended use discussed in this document, viz., predicting the response of a tapered beam tested in the laboratory. The following two validation approaches were considered: (a) a case where uncertainty data were not available and obtained instead from subject matter experts. (b) a case where uncertainty data were available from repeat tests and calculations.

An Illustration of the Concepts of Verification and Validation in Computational Solid Mechanics

ANSI/ASME V&V10.1-2012 计算固体力学中验证和批准概念的例证

An Illustration of the Concepts of Verification and Validation in Computational Solid Mechanics

ANSI/VITA 62-2012 模块化电源标准

The document will provide guidelines to building a power supply module that can be used to power a VPX chassis. The module will fit within the standard envelope defined for VPX modules in the VITA 48 specifications.

Modular Power Supply Standard

GOST R 54989-2012 电子文献信息的长期保存

Long-term preservation of electronic document-based information

ISO/IEC/IEEE 60559:2011 信息技术.微处理器系统.浮点算法

Information technology - Microprocessor Systems - Floating-Point arithmetic

ANSI/VITA 57.1-2010 现场可编程门阵列中间层卡(FMC)标准

This specification describes FMC IO modules and introduces an electro-mechanical standard that creates a low overhead protocol bridge between front panel IO, on the mezzanine module, and an FPGA processing device on the carrier card, which accepts the mezzanine module.

FPGA Mezzanine Card (FMC) Standard

ANSI/IEEE 1680.1:2010 个人电脑产品的环境评定标准(包括笔记本型个人电脑、桌上个人电脑和个人电脑显示器)

This Standard defines environmental performance criteria for personal computer products, including desktop computers, notebook computers, and computer displays.

Standard for Environmental Assessment of Personal Computer Products, Including Notebook Personal Computers, Desktop Personal Computers, and Personal Computer Displays

GOST R 53940-2010 收银机.产品及其应用程序的一般要求

Cash register machines. General requirements for product and its application procedure

ANSI/VITA 48.0-2010 使用坚固耐用设计执行（REDI）的微型计算机的机械规范

Each of the lower level standards focuses on a specific cooling method and will define the mechanical requirements that are needed to ensure mechanical interchangeability in the sub-rack. This standard utilizes a common circuit board for all the cooling methods and incorporates the features required to achieve 2 Level Maintenance compatibility.

Mechanical Specification for Microcomputers Using Ruggedized Enhanced Design Implementation (REDI)