43.120 电车 标准查询与下载

T/ZS 0484-2023 氢能应急电源车技术规范

前言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本要求　 5 安全要求　 6 功能要求　 7 技术要求　 8 试验　 9 检验规则　 10 随车文件　 11 标志、包装、运输与贮存　

Technical specification for hydrogen emergency power supply vehicle

IEC PAS 63472:2023 插头、插座、车辆连接器和车辆插孔 电动车辆的传导充电 FF AC/DC接触管车辆耦合器配置的尺寸兼容性描述

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Dimensional compatibility description for configuration FF AC/DC contact-tube vehicle coupler

IEC 61980-2:2023 电动汽车无线电力传输（WPT）系统.第2部分:MF-WPT系统通信和活动的特殊要求

Electric vehicle wireless power transfer (WPT) systems - Part 2: Specific requirements for MF-WPT system communication and activities

GSO ECE GTR 13:2023 氢能汽车和燃料电池的全球技术法规

This regulation applies to all hydrogen fuelled vehicles of Category 1-1 and 1-2, with a gross vehicle mass (GVM) of 4,536 kilograms or less.

اللائحة الفنية العالمية على مركبات الهيدروجين وخلايا الوقود

T/BJQC 201905-2023 智能网联汽车信息安全测试方法和判定准则

      本文件规定了智能网联汽车整车（以下简称整车）的网络架构、ECU、IVI、T-BOX、无线通信、TSP云平台、APP和OTA升级的信息安全测试方法和判定准则。       本文件适用于智能网联汽车整车及关键系统、零部件信息安全的测试方法和判定准则。       本文件代替T/BJQC 201905—2021《智能网联汽车信息安全测试方法和判定准则》，与T/BJQC 201905—2021相比，除结构调整和编辑性改动外，主要技术变化如下：     a) 增加了UDS诊断安全测试（见 7.1.4）；     b) 增加了ECU硬件安全测试试验方法（见7.2.1a）、b)、c)）；     c) 增加了IVI操作系统安全测试试验方法（见7.4.2h）、i)、j)）      d) 增加了IVI数据安全测试试验方法（见7.4.6b））     e) 修改了硬件安全测试试验方法（见7.4.1f）、i)、j)、k)）

The method and criterion of cyber security for intelligent connected vehicle

BS EN IEC 61980-3:2022 电动汽车无线电力传输(WPT)系统 磁场无线电力传输系统的具体要求

1   Scope This part of IEC 61980 applies to the off-board supply equipment for wireless power transfer via magnetic field ( MF-WPT ) to electric road vehicles for purposes of supplying electric energy to the RESS (rechargeable energy storage system) and/or other on-board electrical systems. The MF-WPT system operates at standard supply voltage ratings per IEC 60038 up to 1 000 V AC and up to 1 500 V DC from the supply network. The power transfer takes place while the electric vehicle (EV) is stationary. Off-board supply equipment fulfilling the requirements in this document are intended to operate with EV devices fulfilling the requirements described in ISO 19363. The aspects covered in this document include — the characteristics and operating conditions, — the required level of electrical safety, — requirements for basic communication for safety and process matters if required by a MF-WPT system, — requirements for positioning to assure efficient and safe MF-WPT power transfer, and — specific EMC requirements for MF-WPT systems. The following asp...

Electric vehicle wireless power transfer (WPT) systems. Specific requirements for magnetic field wireless power transfer systems

BS ISO 21782-1:2023 电力驱动的道路车辆 电力推进部件的测试规范 一般测试条件和定义

1   Scope This document specifies the test procedures for performance and operating load for voltage class B electric propulsion components (motor, inverter , DC/DC converter ) and their combinations ( motor system ) of electrically propelled road vehicles. This document specifies the terms and definitions used in the ISO 21782 series and general test conditions.

Electrically propelled road vehicles. Test specification for electric propulsion components. General test conditions and definitions

T/QCFW 001-2023 电动汽车动力电池延保服务规范

    本标准旨在通过电动汽车动力电池延保服务规范的推广和普及。     本标准规定了电动汽车动力电池延保服务主体要求、延保服务流程、延保服务安全管理等方面的要求，为电动汽车动力电池延保市场的规范化发展提供依据和支撑，有效促进电动汽车动力电池延保服务行业良性发展。

Extended warranty services specification for electric vehicle power battery

ISO 21782-1:2023 电动道路车辆.电动推进部件的试验规范.第1部分:一般试验条件和定义

This document specifies the test procedures for performance and operating load for voltage class B electric propulsion components (motor, inverter, DC/DC converter) and their combinations (motor system) of electrically propelled road vehicles. This document specifies the terms and definitions used in the ISO 21782 series and general test conditions.

Electrically propelled road vehicles — Test specification for electric propulsion components — Part 1: General test conditions and definitions

IEC PAS 61851-1-1:2023 电动汽车传导充电系统 第 1-1 部分：使用 4 型车辆耦合器的电动汽车传导充电系统的具体要求

Electric vehicle conductive charging system - Part 1-1: Specific requirements for electric vehicle conductive charging system using type 4 vehicle coupler

BS ISO 15118-9:2022 公路车辆 车辆到电网通信接口 无线通信的物理和数据链路层一致性测试

1   Scope This document specifies conformance tests in the form of an abstract test suite ( ATS ) for a system under test ( SUT ) implementing an electric-vehicle or supply-equipment communication controller (EVCC or SECC) with support for WLAN-based high-level communication (HLC) according to ISO 15118‑8 and against the background of ISO 15118‑1. These conformance tests specify the testing of capabilities and behaviours of an SUT , as well as checking what is observed against the conformance requirements specified in ISO 15118‑8 and against what the implementer states the SUT implementation's capabilities are. The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118‑8. The behaviour tests of the ATS examine an implementation as thoroughly as practical over the full range of dynamic conformance requirements defined in ISO 15118‑8 and within the capabilities of the SUT (see NOTE below). A test architecture is described in correspondence to the ATS . The abstract test cases in this document are described leveraging this test architecture and are specified in descriptive tabular format for the ISO/OSI physical and data link layers (layers 1 and 2). In terms of coverage, this document only covers normative sections and requirements in ISO 151...

Road vehicles. Vehicle to grid communication interface - Physical and data link layer conformance test for wireless communication

BS ISO 6469-1:2019+A1:2022 电力驱动的道路车辆 安全规范-可充电储能系统（RESS）

1   Scope This document specifies safety requirements for rechargeable energy storage systems ( RESS ) of electrically propelled road vehicles for the protection of persons. It does not provide the comprehensive safety information for the manufacturing, maintenance and repair personnel. NOTE 1 Requirements for motorcycles and mopeds are specified in ISO 13063 and ISO 18243. NOTE 2 Additional safety requirements can apply for RESS that can be recharged by means different from supplying electric energy (e.g. redox flow battery).

Electrically propelled road vehicles. Safety specifications - Rechargeable energy storage system (RESS)

KS R 1202-1-2022 电动汽车充电站管理系统.第1部分:一般要求

Electric vehicle charging station management system — Part 1: General requirements

T/CSAE 276-2022 燃料电池堆振动测试技术规范

本文件规定了燃料电池堆的振动测试方法、机械冲击测试方法。 本文件适用于车用燃料电池堆。

Fuel cell stack vibration test specification

KS R ISO 6469-3-2022 电动道路车辆.安全规范.第3部分:电气安全

Electrically propelled road vehicles — Safety specifications — Part 3: Electrical safety

KS R ISO 6469-3:2022 电动道路车辆.安全规范.第3部分:电气安全

Electrically propelled road vehicles — Safety specifications — Part 3: Electrical safety

BS EN IEC 63119-2:2022 电动汽车充电漫游服务信息交换-用例

This part of IEC 63119 specifies roaming use cases of information exchange between EV charging service providers (CSP), charging station operators (CSOs) and clearing house platforms through roaming endpoints. The elementary use cases defined in this document are designed to support the user to have access to the EV supply equipment which does not belong to the home-CSP. exchange/interaction between different CSPs, as well as between a CSP and CSO with or without clearing house platform through the roaming endpoint. and charging station operator (CSO) or between EV and CS.

Information exchange for electric vehicle charging roaming service - Use cases

ISO 15118-9:2022 道路车辆.车辆到电网通信接口.第9部分:无线通信的物理和数据链路层一致性试验

This document specifies conformance tests in the form of an abstract test suite (ATS) for a system under test (SUT) implementing an electric-vehicle or supply-equipment communication controller (EVCC or SECC) with support for WLAN-based high-level communication (HLC) according to ISO 15118-8 and against the background of ISO 15118-1. These conformance tests specify the testing of capabilities and behaviours of an SUT, as well as checking what is observed against the conformance requirements specified in ISO 15118-8 and against what the implementer states the SUT implementation's capabilities are. The capability tests within the ATS check that the observable capabilities of the SUT are in accordance with the static conformance requirements defined in ISO 15118-8. The behaviour tests of the ATS examine an implementation as thoroughly as practical over the full range of dynamic conformance requirements defined in ISO 15118-8 and within the capabilities of the SUT (see NOTE below). A test architecture is described in correspondence to the ATS. The abstract test cases in this document are described leveraging this test architecture and are specified in descriptive tabular format for the ISO/OSI physical and data link layers (layers 1 and 2). In terms of coverage, this document only covers normative sections and requirements in ISO 15118-8. This document can additionally refer to specific tests for requirements on referenced standards (e.g. IEEE, or industry consortia standards, like WiFi Alliance) as long as they are relevant in terms of conformance for implementations according to ISO 15118-8. However, it is explicitly not intended to widen the scope of this conformance specification to such external standards, if it is not technically necessary for the purpose of conformance testing for ISO 15118-8. Furthermore, the conformance tests specified in this document do not include the assessment of performance nor robustness or reliability of an implementation. They cannot provide judgments on the physical realization of abstract service primitives, how a system is implemented, how it provides any requested service, nor the environment of the protocol implementation. Furthermore, the abstract test cases defined in this document only consider the communication protocol and the system's behaviour defined ISO 15118-8. The power flow between the EVSE and the EV is not considered. NOTE Practical limitations make it impossible to define an exhaustive test suite, and economic considerations can restrict testing even further. Hence, the purpose of this document is to increase the probability that different implementations are able to interwork. This is achieved by verifying them by means of a protocol test suite, thereby increasing the confidence that each implementation conforms to the protocol specification. However, the specified protocol test suite cannot guarantee conformance to the specification since it detects errors rather than their absence. Thus, conformance to a test suite alone cannot guarantee interworking. Instead, it gives confidence that an implementation has the required capabilities and that its behaviour conforms consistently in representative instances of communication.

Road vehicles — Vehicle to grid communication interface — Part 9: Physical and data link layer conformance test for wireless communication

IEC 61980-3:2022 电动车辆无线电力传输（WPT）系统.第3部分:磁场无线电力传输系统的特殊要求

Electric vehicle wireless power transfer (WPT) systems - Part 3: Specific requirements for magnetic field wireless power transfer systems

ISO 6469-1:2019/Amd 1:2022 电动道路车辆.安全规范.第1部分:可再充电能量存储系统（RESS）.修改件1:热传播的安全管理

Electrically propelled road vehicles — Safety specifications — Part 1: Rechargeable energy storage system (RESS) — Amendment 1: Safety management of thermal propagation