55.040 包装材料和辅助物 标准查询与下载

T/CPF 0071-2023 质量分级及“领跑者”评价要求 食品包装容器用聚乙烯发泡垫片

本文件规定了食品包装容器用聚乙烯发泡垫片产品质量及企业标准水平的基本要求、评价指标及要求、评价方法及等级划分和产品质量分级。

Assessment requirements for quality grading and forerunner— Polyethylene foam liner for food packaging containers

DB23/T 3586-2023 电商快件绿色包装通用要求

General requirements for green packaging for e-commerce express shipments

ASTM F88/F88M-23 柔性屏障材料密封强度的标准测试方法

1.1  This test method covers the measurement of the strength of seals in flexible barrier materials. 1.2  The test may be conducted on seals between a flexible material and another flexible material, a rigid material, or a semi-rigid material. 1.3  Seals tested in accordance with this test method may be from any source, laboratory or commercial. 1.4  This test method measures the force required to separate a test strip of material containing the seal. It also identifies the mode of specimen failure. 1.5  This test method differs from Test Method F2824 . Test Method F2824 measures mechanical seal strength while separating an entire lid (cover/membrane) from a rigid or semi-rigid round container. 1.6  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Seal Strength of Flexible Barrier Materials

ASTM E619-17(2023) 评定纸包装中外来气味和/或香料的标准实施规程

Standard Practice for Evaluating Foreign Odors and/or Flavors from Paper Packaging

T/CNFIA 178-2023 液体食品用无菌纸基复合包装环境友好性评价准则

1、范围 2、规范性引用文件 3、术语和定义 4、基本要求 5、评价指标体系 6、评价方法 7、评价报告 8、产品标识

Evaluation criteria for environmental friendliness of aseptic paper-based composite packaging for liquid foods

T/HEBQIA 177-2023 啤酒桶内袋

本文件规定了啤酒桶内袋的材料结构、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

beer keg inner bag

T/HEBQIA 176-2023 啤酒包装袋

本文件规定了啤酒包装袋的材料结构、技术要求、试验方法、检验规则、标志、包装、运输和贮存。

beer packaging bag

ASTM D3950-23 非金属捆扎（和连接方法）的标准规范

Standard Specification for Strapping, Nonmetallic (and Joining Methods)

T/ZZB 3067-2023 柔性减塑聚丙烯打包带

本文件规定了柔性减塑聚丙烯打包带（以下简称打包带）的术语和定义、产品规格、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存及质量承诺。  本文件适用于以聚丙烯（PP）为主要原料，经挤出单向拉伸成型，配合自动打包机使用的打包带。

Flexible and plastic reducible PP strapping

T/ZSHG 022-2023 手枪泵产品测试方法

4　测试内容 4.1　外观 4.2　尺寸 4.3　产品力学性能 产品力学性能的测试内容如下： a)引液管拉脱力； b)锁瓶盖拧紧扭矩； c)锁瓶盖打开扭矩。 4.4　产品使用性能 产品使用性能的测试内容如下： a)起泵空压次数； b)泵出量； c)耐疲劳性； d)喷空测试； e)喷出图形； f)喷角（适用于喷雾型手枪泵）； g)喷程（适用于喷雾型手枪泵）； h)雾粒粒径及其分布（适用于喷雾型手枪泵）。 4.5　产品安全性能 产品安全性能的测试内容如下： a)抗冲击性试验； b)真空泄漏试验； c)有害物质限值； d)微生物限度。 4.6　产品稳定性 产品稳定性的测试内容如下： a)耐高温稳定性； b)耐低温稳定性。 4.7　相容性 4.8　可浮性（适用于可回收再生利用的产品）

Test method for trigger pump products

T/ZSHG 021-2023 定量型气雾阀

外观：定量型气雾阀应完整无缺损，整体洁净、完好，内外表面保护层应无划伤，无脱落。               各配件安装的位置正确。 尺寸：定量型气雾阀尺寸，见图2、表1和表2。           定量型气雾阀阀杆高度H2 尺寸偏差为±0.30 mm。           定量型气雾阀阀杆顶端直径d1 尺寸偏差为0 mm～0.10 mm。           引液管计算长度L 尺寸偏差：           L≤150 mm为±1.5 mm；          150 mm＜L≤220 mm为±2.0 mm；          L＞220 mm为±3.0 mm。 性能：        畅通性：定量型气雾阀促动时所有通道应畅通。        密封性：定量型气雾阀在大于或等于0.85 MPa压力下保持1 min不泄漏。        固定盖耐压性：定量型气雾阀在1.8 MPa压力下保持1 min，固定盖小凸台高度h变化值Δh小于或等于0.30 mm。        引液管拉脱力：定量型气雾阀引液管拉脱力大于或等于15 N。        阀体压脱力：定量型气雾阀阀体压脱力大于或等于180 N。        定量检测：定量型气雾阀按压应定量。        一次喷量：定量型气雾阀一次喷量允许误差±15%。        每罐总揿次：定量型气雾剂每罐总揿次应符合产品标示总揿次。        定量型气雾阀年泄漏率：定量型气雾阀年泄漏率应不超过10%。 相容性：定量型气雾剂产品的内容物成分不同，对定量型气雾阀各配件要求各异，生产厂应向用户提供样品作相容性试验，并取得确认。 有害物质限值：定量型气雾剂产品的分类不同，对定量型气雾阀各配件要求各异，有害物质限值要求应按国家相关规定执行。 微生物限度：用于化妆品类、食品类或医药用品类的定量型气雾阀，对定量型气雾阀各配件要求各异，微生物限度要求应按国家相关规定执行。

Metering aerosol valve

T/GDEIA 21-2023 电化铝高速烫印膜

该标准规定了电化铝高速烫印膜的外观质量、产品规格、物理指标、挥发性有机化合物VOC限量等技术要求、试验方法、检验规则、标志、标签、包装、运输、贮存等内容。

Electrolytic Aluminum High-speed Hot Stamping Film

T/GDEIA 22-2023 压敏胶带用非硅离型膜

该标准规定了压敏胶带用非硅离型膜的外观、尺寸偏差、性能指标、环保要求等技术要求、试验方法、检验规则、标志、标签、包装、运输、贮存等内容。

Non silicon release film for pressure sensitive tape

BB/T 0053-2023 模内标签

In-mold label

BB/T 0031-2023 电化铝烫印箔

Stamping foil

T/CPF 0055-2023 紫外发光二极管光固化印铁胶印油墨

本文件规定了紫外发光二极管光固化（简称“LED-UV”）印铁胶印油墨产品的要求、试验方法、检验规则及标志、包装、运输和贮存。

Metal decorating LED-UV offset ink

ASTM F3039-23 通过染料渗透检测无孔包装或柔性阻隔材料泄漏的标准测试方法

1.1 Method A of this test method defines a procedure that will detect and locate a leak equal to or greater than a channel formed by a 50 µm [0.002 in.] wire in the edge seals of a nonporous package. A dye penetrant solution is applied locally to the seal edge to be tested for leaks. After contact with the dye penetrant for a minimum specified time, the package is visually inspected for dye penetration or, preferably, the seal edge is placed against an absorbent surface and the surface inspected for staining from the dye. 1.2 Method B for this test method also defines a procedure that will detect and locate a leak equal to or greater than 10 µm [0.00039 in] diameter in a nonporous flat sheet. The flat sheet is placed on an absorbent surface and then a dye penetrant is spread across the surface of the sheet, preferably using a small roller to apply pressure on the sheet to ensure adequate contact between the absorbent surface and the bottom surface of the sample being tested. The flat sheet is carefully removed and the absorbent surface is inspected for staining from the dye. 1.3 These test methods are used for both transparent and opaque nonporous surfaces. 1.4 These test methods require that the dye penetrant have good contrast to the materials being tested and/or the absorbent surface. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Detecting Leaks in Nonporous Packaging or Flexible Barrier Materials by Dye Penetration

ASTM F1115-16(2023) 测定饮料容器二氧化碳损失的标准试验方法

1.1 The objective of this test method is to determine the carbon dioxide (CO2) loss from plastic beverage containers after a specified period of storage time. 1.2 Factors contributing to this pressure loss are volume expansion and the gas transport characteristics of the package, including permeation and leakage. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Carbon Dioxide Loss of Beverage Containers

ASTM F3300-23 使用往复加重触针测定软包装薄膜耐磨性的标准测试方法

1.1 This test method covers the determination of the abrasion resistance of flexible non-conductive films and packaging materials using a weighted stylus that wears completely through a film by oscillating or reciprocating back and forth along a linear path until an electrical circuit is completed shutting down the test. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Abrasion Resistance of Flexible Packaging Films Using a Reciprocating Weighted Stylus

T/HEBQIA 149-2023 药用包装吨袋

本文件规定了药用包装吨袋的术语和定义、要求、试验方法、检验规则、标志、包装、运输、贮存。

Pharmaceutical packaging ton bag