79.080 半成品材 标准查询与下载

T/WJMC 010-2023 水性漆木质门

规范了水性漆涂料及水性漆室内民用木质门术语及定义、水性漆木质门技术要求、测量和检验方法、检验规则、理化性能及标志、包装。

Water-based paint interior wooden door

BS ISO 4562:2023 木镶木条 分类

Wood parquet strips. Classification

23/30465602 DC BS EN 13226 木地板 带凹槽和/或榫舌的实心镶木地板元件

BS EN 13226. Wood flooring. Solid parquet elements with grooves and/or tongues

BS EN 13442:2023 木质和镶木地板以及木质镶板和覆层 耐化学试剂性的测定

1   Scope This document specifies a test method to determine the resistance of the surface of an element of wood flooring, panelling and cladding, to a predetermined list of chemical agents they may be exposed to during their service life.

Wood and parquet flooring and wood panelling and cladding. Determination of the resistance to chemical agents

T/QGCML 759-2023 耐温变木塑板制备方法

本标准规定了耐温变木塑板制备方法的术语和定义、技术要求、检验方法、检验规则、标志、包装、运输和贮存。 本标准适用于耐温变木塑板的生产及检验过程。

Preparation method of temperature-resistant wood-plastic board

ISO 4561:2023 木材原料 分类

Wood raw elements — Classification

ISO 4556:2023 原木镶木地板元件 一般特性

Wood raw parquet elements — General characteristics

ISO 4562:2023 实木复合地板条 分类

Wood parquet strips — Classification

T/QGCML 650-2023 复合木地板通用技术规范

本标准规定了复合木地板通用技术规范的术语和定义、技术要求、检验方法、检验规则、标志、包装、运输和贮存。 本标准适用于复合木地板的生产及检验。

General technical specification for composite wood flooring

ASTM D8023-23 木结构用圆形木钉（销钉）标准规范

1.1 This specification covers standardizing the dimensions and materials for the manufacture of round wood dowels (pegs) used in the fabrication of connections in wood construction. The referencing of this specification in design, construction, and purchase order documents is intended to provide some assurance that the round wood dowels to be used in an assembly meet minimum materials-quality standards and that dimensions for fabrication and finish can be relied on to ensure connection performance. This specification provides regulatory agencies with a set of standards by which to judge the acceptability of round wood dowels encountered in the field and in fabricators’ shops. 1.2 This specification only addresses the standardization and manufacture of round wood dowels. Other types of wood dowels, such as sawn or cleaved pegs, are outside the scope of this specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 Safety Hazards—There are no known hazards with the use of this specification. The products manufactured to this specification should not be brittle or difficult to install with proper tools. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Round Wood Dowels (Pegs) for Use in Wood Construction

KS F 2154-2022 轻型框架木剪力墙抗剪切（开裂）试验方法

Method of shear(racking) resistance test for light-frame wood shear walls

DB3713/T 268-2022 人造板饰面用复贴材料技术规范

Technical specification for pasting materials for wood-based panels

ASTM D6815-22a 木材和木基产品负载和蠕变效应持续时间的评估

1.1 This specification provides a procedure for testing and evaluating duration of load and creep effects of wood and wood-based materials relative to an accepted duration of load adjustment model. This specification was created for products that are currently covered by a consensus standard (for example, lumber, structural composite lumber, and structuraluse panels). This procedure is intended to demonstrate the engineering equivalence to the duration of load and creep effects of visually graded lumber as specified in Practice D245 for a product under evaluation used in dry service conditions. This procedure is not intended to evaluate the performance of products under impact loading. Quantification of specific duration of load or creep factors is beyond the scope of this specification. For further guidance regarding the applicability of this specification refer to X1.1 in the Commentary. 1.2 Use of the procedure in this specification to determine equivalence to the Practice D245 duration of load relationship is limited to solid wood and wood-based products whose long term load behavior is similar to that of solid wood. Equivalence demonstrated in this specification is dependent upon evaluation of a product’s 90-day (minimum) creep-rupture performance. In this evaluation, three criteria must be satisfied: (1) adequate strength over a 90-day period, (2) decreasing creep rate, and (3) limited fractional deflection. A summary of the development of these criteria and the underlying assumptions behind them is provided in the Commentary in Appendix X1 and Appendix X2. 1.3 Long term degradation phenomena not described by a creep-rupture model are not addressed in this specification (see Commentary X1.2.4). 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products

T/WJMC 008-2022 室内实木复合门

规范了室内实木复合门分类、规格、材料、规格尺寸及偏差、外观要求、检验方法、判定规则及标志、包装、运输和贮存。

Indoor wood composite door

T/WJMC 007-2022 民用木质门

规范了民用木质门分类、要求、包括：材料、规格尺寸及偏差、外观质量、门扇、门框理化性能、测量和检验方法、检验规则。

Civil wooden door

T/CTWPDA 13-2022 低光泽度实木复合地板

本文件规定了低光泽度实木复合地板的术语、定义、分类、要求、检验方法、检验规则以及标志、包装、运输和贮存。 本文件适用于低光泽度实木复合地板。

Low gloss parquet

T/CTWPDA 14-2022 膜饰面实木地板

本文件规定了膜饰面实木地板的术语和定义、分类、要求、检验方法、检验规则以及标识、包装、运输和贮存等。 本文件适用于膜饰面实木地板。

Film-overlaid solid wood flooring

LY/T 2143-2022 实木衣架

Solid wood hanger

ASTM D6815-22 木材和木基产品的负荷持续时间和蠕变效应的评估标准规范

Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products

ASTM D25-12(2022) 通过组分分析计算液化石油气的某些物理性质的标准实施规范

1.1 This specification covers the physical characteristics of unused round timber piles to be used either treated or untreated. 1.2 This specification is not intended for preused piles unless the piles have the quality specified by this specification and design stresses equal to or greater than those derived from Method D2899. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Round Timber Piles