79.080 半成品材 标准查询与下载

T/DBXH 004-2019 E0级浸渍纸层压木质地板

1、规格尺寸及偏差； 2、外观质量； 3、理化性能：静曲强度、内结合强度、含水率、密度、吸水厚度膨胀率、表面胶合强度、表面耐冷热循环、 表面耐划痕、尺寸稳定性、表面耐磨、表面耐香烟灼烧、表面耐干热、表面耐污染腐蚀、表面耐龟裂、抗冲击、耐光色牢度、甲醛释放量、挥发性有机化合物（72h）

E0 grade laminate flooring

T/DBXH 003-2019 E0级实木复合地板

1、规格尺寸及其偏差； 2、外观质量； 3、理化性能：浸渍剥离、静曲强度、弹性模量、含水率、漆膜附着力、表面耐磨、漆膜硬度、表面耐污染、 甲醛释放量、挥发性有机化合物（72h）

E0 grade engineered wood flooring

T/CNFPIA 3004-2019 石木塑地板

本标准规定了石木塑地板的术语和定义、分类、技术要求、检验方法、检验规则、标志、包装、运 输和贮存的要求。

Stone wood plastic floor

ASTM D5055-19e1 预制木工字梁结构能力的建立和监测的标准规范

1.1 General—This specification gives procedures for establishing, monitoring, and reevaluating structural capacities of prefabricated wood I-joists. Capacities considered are shear, reaction, moment, and stiffness. Procedures for establishing common details are given and certain design considerations specific to wood I-joists are itemized. 1.2 Contents of the Standard—An index and brief description of the main features of this specification are given in X2.1.1. 1.3 Development of the Standard—The development and intent of this specification is discussed in Appendix X2. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in 6.1.1.5. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists

ASTM D5055-19 预制木工字梁结构能力的建立和监测的标准规范

Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists

T/ZZB 0946-2019 地采暖用实木地板

本标准规定了地采暖用实木地板的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、包装、标志、运输和贮存、质量承诺。 本标准适用于阔叶树材制成的室内用地采暖实木地板。

Solid wood flooring for ground with heating system

ASTM F2421-19a 用百分表测量弹性地板的标准试验方法

1.1 This test method establishes the procedures for determination of both dimension (length and width) and squareness of a rectangular resilient floor plank. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are provided in applicable sections of this test method. 1.4 The values stated in inch-pounds units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement of Resilient Floor Plank by Dial Gauge

ASTM F2421-19 用表盘测量弹性地板的标准试验方法

Standard Test Method for Measurement of Resilient Floor Plank by Dial Gage

LY/T 3035-2018 车削类工具木柄

Turning tools wooden handles

LY/T 1700-2018 地采暖用木质地板

Wooden floor for floor heating

LY/T 3037-2018 乙酰化木材

acetylated wood

T/ZZB 0892-2018 木质相框

本标准规定了木质相框的术语和定义、基本要求、技术要求、检验方法、检验规则、标志、包装、运输和贮存以及质量承诺。 本标准适用于室内干燥环境的木质类相框、镜框、装饰画产品。

Wooden photo frame

T/ZZB 0833-2018 浸渍纸层压木质地板

本标准规定了室内用浸渍纸层压木质地板产品的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、包装、标识、运输和贮存、质量承诺。 本标准适用于浸渍纸层压木质地板。

Laminate flooring

T/XLSA 001-2018 层压木质生态地板

层压木质生态地板理化指标 项　目　单位　优等品　一等品　合格品 静曲强度　Mpa　≥35.0　≥30.0　≥25.0 内结合强度　Mpa　≥1.0 含水率　%　3.0~10.0 密度　g/cm3　≥0.85　≥0.80　≥0.70 吸水厚度膨胀率　%　≤18　≤25 表面胶合强度　Mpa　≥1.0 表面耐冷热循环　-　无龟裂、无鼓泡 表面耐划痕　-　4.0 N表面装饰花纹未划破 尺寸稳定性　mm　≤0.9 表面耐磨　光面层压　转　≥6000　≥4000　≥1000 　浮雕层压　　≥3000　≥2000　≥500 表面耐香烟灼烧　-　无黑斑、裂纹和鼓泡 表面耐干热　-　无龟裂、无鼓泡 表面耐污染腐蚀　-　无污染、无腐蚀 表面耐龟裂　-　用6倍放大镜观察，表面无裂纹 抗冲击　mm　≤9　≤10　≤12 耐光色牢度级　级　≥灰度卡4级

Laminated Wooden Ecological Floor

ASTM D6570-18a 为机械分级木材分配容许属性的标准实践

1.1 This practice covers the methodology of grade qualification, assignment of design properties, and requirements for the quality control of mechanically graded solid sawn lumber. 1.2 This practice acknowledges alternative methods for the assignment of specific properties. These methods are assignment by test, relationship to other properties, and by procedures in other appropriate standards. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Assigning Allowable Properties for Mechanically Graded Lumber

ASTM D6570-18a(2023)e1 分配机械分级木材允许特性的标准实施规程

Standard Practice for Assigning Allowable Properties for Mechanically Graded Lumber

BS PD CEN/TS 16818:2018 木材和木质产品的耐久性 木材和木质产品的水分动力学

Durability of wood and wood-based products. Moisture dynamics of wood and wood-based products

ASTM D6570-18 为机械分级木材分配容许属性的标准实践

Standard Practice for Assigning Allowable Properties for Mechanically Graded Lumber

PD CEN/TS 16818:2018 木材和木制品的耐久性 木材和木制品的水分动力学

Durability of wood and wood-based products - Moisture dynamics of wood and wood-based products

ASTM D4444-13(2018) 手持式水分仪的实验室标准化和校准的标准测试方法

1.1 This test method applies to the measurement of moisture content (MC) of solid wood products, including those containing additives (that is, chemicals or adhesives) for laboratory standardization and calibration of hand-held moisture meters 1.2 This test method makes no distinction between meter measurement technologies for standardization and calibration requirements. Provision is made for test specimen size to accommodate specific meters. Appendix X1 provides an explanatory discussion and history corresponding to the mandatory sections. Fundamental measurement technologies are described in Appendix X2 when available. 1.2.1 Meters employing differing technologies may not provide equivalent readings under the same conditions. When this test method has been applied, it is assumed that the referenced meter is acceptable unless otherwise specified. Meters shall be calibrated with respect to MC by direct measurement as determined by Test Methods D4442. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters