81.100 玻璃和陶瓷生产设备 标准查询与下载

SNI 15-3357-1994 滚式陶瓷搅拌机

Ceramic mixer roll type

SNI 15-3350-1994 陶瓷挤压机

Ceramic extruder machines

GOST 12.2.015-1993 ССБТ.玻璃工业用机器和设备.安全一般要求

Настоящий стандарт распространяется на автоматические и механизированные технологические комплексы, машины и оборудование, входящие в с

Machines and equipment for glass industry. General safety requirements

GOST R 50309-1992 玻璃工业用机器和设备 一般安全要求

Machines and equipment for glass industry. General safety requirements

GOST 27706-1988 制造拉伸玻璃板的槽式炉.耗能指标计算

Bath type ovens for making drawn sheet glass. Calculation of power-consuming indices

GOST 6113-1984 陶制品用卧式螺旋传动压力机.技术条件

Настоящий стандарт распространяется на шнековые горизонтальные прессы (дале - прессы), предназначенные для пластического формования кера

Screw horizontal presses for clayware. Specifications

JIS R 4201:1983 工业用玻璃垫板设备和仪器

Glass-lined apparatus and equipment for industry

JC/T 763-1996 陶瓷工业隧道窑热平衡热效率测定与计算方法

本标准规定了建筑卫生陶瓷隧道窑的热平衡、热效率的测定与计算方法。 本标准适用于生产建筑卫生陶瓷产品中，使用液体、固体和气体燃料的隧道窑热平衡、热效率测定与计算。对于生产陶瓷产品的其它窑炉的热平衡、热效率的测定与计算也可参照采用本标准。

Measurement and calculation method of heat balance and thermal efficiency of ceramic industral tunnel kiln

FprEN 13035-1 平板玻璃制造、处理和加工的机器和设备 安全要求 第1部分：工厂内的储存、搬运和运输设备

1.1 This document includes safety requirements for the design and installation of equipment that is intended for storage, handling, and transportation of flat glass inside the factory. It does not cover all phases of life of the product. Transport to the customer, assembly, dismantling, disabling, or scrapping are excluded. This document also applies to equipment within the scope of Machinery Directive (see 1.2) as well as to equipment that is not covered by Machinery Directive (see 1.3). Annex C (see Figure C.1) gives an overview of the differentiation. NOTE Additional requirements covering specific hazards that result from the use outside the factory are dealt with in FprEN 13035 2:2022. 1.2 This document specifies safety requirements for the following machinery: - machinery for storage provided with elements that are propelled by a drive system other than directly applied human or animal power (engine power) in order to store or retrieve glass in or from storage shelves or frames (see 3.2.2); - machinery for picking up single glass plates, firmly-attached glass plates or glass packs for transportation between different locations where the retention force or lifting force is generated by engine power (see 3.3.2, 3.3.3); - machinery for transportation by special vehicles that are propelled by engine power. 1.3 This document specifies additional requirements in Annex A for the following equipment that is not covered by Machinery Directive: - stationary, movable and mobile storage equipment (see 3.2.1, 3.2.3, 3.2.4); - storage equipment with mobile frame (provided with manually propelled shelves or frames) (see 3.2.2); - equipment for transportation by trailer and trolley (see 3.4.2 and 3.4.3). 1.4 This document only deals with equipment, which is in direct contact with the glass, with the exception of wooden packaging. Tractors, cranes, hoists and forklift trucks as well as elements of self-propelled vehicles, which are not in contact with the glass (see 3.4.1), are out of the scope. This document does not apply to equipment for picking up single plates, such as manual vacuum lifting devices, lifting straps or other manual devices (see 3.3.1). This document does not cover automatic loading or unloading of storage and transportation equipment. This is covered in EN 13035 5:2006+A1:2009. 1.5 This document deals with all significant hazards, hazardous situations and hazardous events, which are relevant to equipment for storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer covered by the Machinery Directive (see Annex B). This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. The significant hazards, hazardous situations and hazardous events during transport to the customer, assembly, dismantling, disabling, or scrapping are excluded. 1.6 This document deals with significant hazards, hazardous situations and hazardous events, which are relevant to equipment for storage, handling and transportation of flat glass outside the Machinery Directive, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A). 1.7 This document provides the requirement on machinery and devices that are in direct or indirect contact with glass. 1.8 This document is not applicable to equipment for storage, handling and transportation of flat glass inside the factory, which is manufactured before the date of publication of this document by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory

FprEN 13035-2 平板玻璃制造、处理和加工的机器和设备-安全要求-第2部分：厂外储存、装卸和运输设备

1.1 This document includes safety requirements for the design and installation of equipment that is intended for storage, handling and transportation of flat glass outside the factory. It applies to machinery within the scope of Machinery Directive as well as to equipment that is not covered by Machinery Directive (see Figure F.1). If machines and equipment are not only used outside the factory, the requirements of EN 13035-1:2008 also apply. 1.2 This document specifies safety requirements for the following machinery for storage (see 3.2.1), handling (see 3.2.2) and transportation (see 3.2.3) of flat glass outside the factory (see 3.1.1): - vehicle-mounted frails with motorized adjustment of the angle of lean for loading and unloading, which are used for road transport; - inloader for road transport outside the factory, where loading and unloading is only made on virtually horizontal and sufficiently stable grounds that are free of significant irregularities; - specific self-propelled equipment for securing the glass (inloader load-securing system, see 3.2.9); - equipment for picking up single glass plates, firmly-attached glass plates or glass packs for transportation between different locations where the retention force or lifting force is generated by engine power. 1.3 This document specifies additional requirements in Annex A for the following equipment that is not covered by Machinery Directive: - vehicle-mounted frails without an adjustable angle of lean for loading and unloading, which are used for road transport; - movable storage equipment designed to transport the glass outside the factory (e.g. inloader stillages, see Figure C.6); - glass-securing devices or systems for transport stillages (e.g. spring tensioning rods, stanchions). NOTE Specific hazards due to the use inside the factory are dealt with in EN 13035-1:2008. This standard is still under review and is published as prEN 13035-1:2020 Machines and plants for the manufacture, treatment, and processing of flat glass - Safety requirements - Part 1: Storage, handling, and transportation equipment inside the factory. 1.4 This document deals with road transport as well as rail transport. 1.5 This document only deals with equipment which is in direct contact with the glass. This document does not apply to manual handling equipment such as carrying straps and manual vacuum lifting devices and to all packaging for glass which always opened and closed in the factory (see EN 13035-1:2008). Tractors, cranes, hoists and forklift trucks as well as elements of self-propelled vehicles, which are not in contact with the glass, are out of the scope. This document does not apply to the transport of glazed windows/frames, neither does it apply to equipment for different transportation than on road or on rail, e.g. by ships. 1.6 This document deals with all significant hazards, hazardous situations and hazardous events, which are relevant to equipment for storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex B). This document specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. Noise hazards have not been considered significant for any type of equipment within the scope of this document. This document does not cover all phases of life of the product like transport to the customer, assembly, dismantling, disabling or scrapping. 1.7 This document does not apply to equipment for storage, handling and transportation of flat glass outside the factory, which is manufactured before the date of publication of this document as EN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 2: Storage, handling and transportation equipment outside the factory