81.100 玻璃和陶瓷生产设备 标准查询与下载

BS EN 13035-7+A1:2008 平面玻璃的制造、处理和加工用机械和设备 安全要求 薄板状玻璃用切割机

Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Cutting machines for laminated glass

BS EN 13035-11:2006 平板玻璃的生产、处理和加工用机械和设备.安全要求.钻床

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Drilling machines

BS EN 13035-5+A1:2008 平面玻璃的制造、处理和加工用机械和设备 安全要求 堆垛和卸垛用机械和设备

Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Machines and installations for stacking and de-stacking

BS EN 13035-6:2006+A1:2009 平板玻璃的生产、处理和加工用机械和设备.安全性要求.粉碎机械

This European Standard applies for machines for break-out of flat glass including the following steps: transport and positioning, break-out, transport of the cut sizes to the unloading position, leading away of waste flat glass.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Machines for break-out

BS EN 13035-5:2006+A1:2009 平面玻璃的制造、处理和加工用机械和设备.安全性要求.堆垛和卸垛用机械和设备

This European Standard applies for machines and installations for stacking and de-stacking that are specifically designed for building-up or taking down upright stacks of flat glass sheet by sheet including unloading and loading of single sheets of flat glass from or onto machines or transport devices (conveyors).

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Machines and installations for stacking and de-stacking

BS EN 13035-7:2006+A1:2009 平面玻璃的制造、处理和加工用机械和设备.安全要求.薄板状玻璃用切割机

1.1 This European Standard applies for cutting machines for laminated glass including the following steps: transport and positioning, synchronous cutting (scoring) from both sides, break-out, electrical heating and separation. 1.2 This European Standard deals with the significant hazards, hazardous situations and events relevant to cutting machines for laminated glass when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). Those hazards, which are dealt with in the ad-hoc standard EN 619 for conveyors are excepted. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. Hazards from noise are not considered to be significant. 1.3 This European Standard is not applicable to cutting (scoring) and break-out of monolithic glass (see EN 13035-3 and EN 13035-6). 1.4 This European Standard is not applicable to the cutting of laminated glass by sawing or by the use of high-pressure liquid. 1.5 This European Standard is not applicable to the significant hazards of conveyors and machines for the manufacture, treatment and processing of flat glass such as tilting tables. 1.6 This European Standard is not applicable to cutting machines for laminated glass which are manufactured before the date of publication of this European Standard by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Cutting machines for laminated glass

BS EN 13035-6:2006 平板玻璃的生产、处理和加工用机械和设备.安全要求.原料制备机械

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Machines for break-out

DIN EN 13035-1:2008 平面玻璃的制造、处理和加工用机械和设备.安全要求.第1部分:工厂内的储存、搬运和运输设备

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage, handling and transportation of flat glass inside the factory as described in Clause 3. It applies to stationary, movable and mobile storage equipment (see 3.2), mechanical and pneumatic handling equipment (see 3.3) and transportation equipment (see 3.4) (see overview in Annex A). 1.2 Additional requirements for dealing with specific hazards due to the use outside the factory are dealt with in prEN 13035-2. 1.3 This standard only deals with the devices which are directly in contact with the glass. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass (see 3.4.1). This standard does not apply to manual handling equipment as defined in 3.3.1. 1.4 This standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard. 1.5 This document is not applicable to storage, handling or transportation equipment for flat glass inside the factory, which is manufactured before the date of its publication as EN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory; English version of DIN EN 13035-1:2008-06

LST EN 13035-2-2008 平板玻璃制造、处理和加工的机器和设备-安全要求-第2部分：厂外储存、装卸和运输设备

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 2: Storage, handling and transportation equipment outside the factory

LST EN 13035-1-2008 平板玻璃制造、处理和加工的机器和设备 安全要求 第1部分：工厂内的储存、搬运和运输设备

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory

DS/EN 13035-2:2008 平板玻璃制造、处理和加工的机器和设备-安全要求-第2部分：厂外储存、装卸和运输设备

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage (as defined in 3.2.1), handling (as defined in 3.2.2) and transportation (as defined in 3.2.3) of flat glass outside the factory (as defined in 3.1.1) and including stillages, pallets, frails fixed to vehicles, in-loader vehicles, specific glass-securing devices, stanchions and vacuum-lifting devices which are used for road transport and on building sites.1.2 Specific hazards due to the use inside the factory are dealt with in EN 13035-1.1.3 This standard deals only with the devices which are directly in contact with the glass. This s

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 2: Storage, handling and transportation equipment outside the factory

DS/EN 13035-1:2008 平板玻璃制造、处理和加工的机器和设备 安全要求 第1部分：工厂内的储存、搬运和运输设备

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage, handling and transportation of flat glass inside the factory as described in Clause 3. It applies to stationary, movable and mobile storage equipment (see 3.2), mechanical and automatic handling equipment (see 3.3) and transportation equipment (see 3.4) (see overview in Annex A).1.2 Additional requirements for dealing with specific hazards due to the use outside the factory are dealt with in prEN 13035-2.1.3 This standard only deals with the devices which are directly in contact with the glass. Tractors, cranes, hoists and fork lifts

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory

BS EN 13035-1:2008 平面玻璃的制造、处理和加工用机械和设备.安全要求.工厂内部储存、装卸与运输设备

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage, handling and transportation of flat glass inside the factory as described in Clause 3. It applies to stationary, movable and mobile storage equipment (see 3.2), mechanical and pneumatic handling equipment (see 3.3) and transportation equipment (see 3.4) (see overview in Annex A). 1.2 Additional requirements for dealing with specific hazards due to the use outside the factory are dealt with in prEN 13035-2. 1.3 This standard only deals with the devices which are directly in contact with the glass. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass (see 3.4.1). This standard does not apply to manual handling equipment as defined in 3.3.1. 1.4 This standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard. 1.5 This document is not applicable to storage, handling or transportation equipment for flat glass inside the factory, which is manufactured before the date of its publication as EN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory

BS EN 13035-2:2008 平面玻璃的制造、处理和加工用机械和设备.安全要求.工厂外部储存、装卸与运输设备

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage (as defined in 3.2.1), handling (as defined in 3.2.2) and transportation (as defined in 3.2.3) of flat glass outside the factory (as defined in 3.1.1) and including stillages, pallets, frails fixed to vehicles, inloader vehicles, specific glass-securing devices, stanchions and vacuum-lifting devices which are used for road transport and on building sites. 1.2 Specific hazards due to the use inside the factory are dealt with in EN 13035-1. 1.3 This standard deals only with the devices which are directly in contact with the glass. This standard does not apply to manual handling equipment such as carrying straps and vacuum pads. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass. This European Standard does not apply to equipment for the transport by other ways than on road e.g. by ship or train, and the transportation of glazed windows/frames. 1.4 This standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard. 1.5 This document is not applicable to storage, handling or transportation equipment for flat glass outside the factory, which is manufactured before the date of its publication as EN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 2: Storage, handling and transportation equipment outside the factory

BS EN 13035-9:2006 平面玻璃的制造、处理和加工用机械和设备.安全要求.第9部分:清洗装置

1.1 This European Standard contains the safety requirements for the design and installation of stationary glass washing installations as shown as typical in Annex A. Glass washing installations are designed to perform the following functions: feeding of flat glass to the cleaning and drying unit and transport (delivery) to the estimation equipment and to the take-off position of the flat glass sheet. None of the processing phases requires direct manual intervention. 1.2 This European Standard deals with the significant hazards, hazardous situations and events with the exception of those by interfaces with other machines used in a process line relevant to glass washing installations, when they are used as intended and under the conditions foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks which can arise from these significant hazards during commissioning, the operation and maintenance. 1.3 This European Standard is not applicable to machines for loading and unloading of glass (see EN 13035-5) and to conveyors (see EN 619) and fans. If there are specific risks that arise by their use as an integral part of flat glass washing installations, appropriate measures are specified. 1.4 This European Standard is not applicable to glass washing installations for automotive and bent glass. 1.5 This European Standard is not applicable to water preparation and disposal of waste washing liquid. 1.6 This European Standard is not applicable to machinery manufactured before the date of publication of this European Standard by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass — Safety requirements — Part 9: Washing installations

BS EN 13035-9+A1:2008 平面玻璃的制造、处理和加工用机械和设备 安全要求 第9部分：清洗装置

Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Washing installations

BS EN 13035-9:2006+A1:2010 平面玻璃的制造、处理和加工用机械和设备.安全性要求.第9部分:清洗装置

1.1 This European Standard contains the safety requirements for the design and installation of stationary glass washing installations as shown as typical in Annex A. Glass washing installations are designed to perform the following functions: feeding of flat glass to the cleaning and drying unit and transport (delivery) to the estimation equipment and to the take-off position of the flat glass sheet. None of the processing phases requires direct manual intervention. 1.2 !This European Standard deals with the significant hazards, hazardous situations and events with the exception of those by interfaces with other machines used in a process line relevant to glass washing installations, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4)." This European Standard specifies the appropriate technical measures to eliminate or reduce risks which can arise from these significant hazards during commissioning, the operation and maintenance. ! Safety requirements and/or protective measures are given in Clause 5. When references are made to B level standards such as EN 953, EN 1037, EN 1088, EN 60204-1, EN ISO 13850 and EN ISO 13857, the manufacturer should carry out an adequate risk assessment for the requirements thereof where choice is necessary." 1.3 This European Standard is not applicable to machines for loading and unloading of glass (see EN 13035-5) and to conveyors (see EN 619) and fans. If there are specific risks that arise by their use as an integral part of flat glass washing installations, appropriate measures are specified. 1.4 This European Standard is not applicable to glass washing installations for automotive and bent glass. 1.5 This European Standard is not applicable to water preparation and disposal of waste washing liquid. 1.6 This European Standard is not applicable to machinery manufactured before the date of publication of this European Standard by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Washing installations

EN 13035-2:2008 平面玻璃的制造,处理和加工用机械和设备.安全要求.第2部分:工厂外部储存,装卸与运输设备

This standard contains the requirements for safety for the design and installation of equipment intended for the storage (as defined in 3.2.1), handling (as defined in 3.2.2) and transportation (as defined in 3.2.3) of flat glass outside the factory (as defined in 3.) and including stillages, pallets, frails fixed to vehicles, inloader vehicles, specific glass-securing devices, stanchions and vacuum-lifting devices which are used for road transport and on building sites. Specific hazards due to the use inside the factory are dealt with in EN 13035-1.This standard deals only with the devices which are directly in contact with the glass.This standard does not apply to manual handling equipment such as carrying straps and vacuum pads. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass.This European Standard does not apply to equipment for the transport by other ways than on road e. g. by ship or train, and the transportation of glazed windows/frames.This standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard.This document is not applicable to storage, handling or transportation equipment for flat glass outside the factory, which is manufactured before the date of its publication as EN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 2: Storage, handling and transportation equipment outside the factory

EN 13035-1:2008 平面玻璃的制造,处理和加工用机械和设备.安全要求.第1部分:工厂内部储存,装卸与运输设备

This standard contains the requirements for safety for the design and installation of equipment intended for the storage, handling and transportation of flat glass inside the factory as described in Clause 3. It applies to stationary, movable and mobile storage equipment (see 3.2), mechanical and pneumatic handling equipment (see 3.3) and transportation equipment (see 3.4) (see overview in Annex A). Additional requirements for dealing with specific hazards due to the use outside the factory are dealt with in prEN 13035-2.This standard only deals with the devices which are directly in contact with the glass. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass (see 3.4.1).This standard does not apply to manual handling equipment as defined in 3.3.1.This standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard.This document is not applicable to storage, handling or transportation equipment for flat glass inside the factory, which is manufactured before the date of its publication as EN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory

CEN EN 13035-2-2008_ 制造、处理和加工平板玻璃的厂房和机械.安全性要求.第2部分:工厂外的储存、处理和运输设备

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage (as defined in 3.2.1), handling (as defined in 3.2.2) and transportation (as defined in 3.2.3) of flat glass outside the factory (as defined in 3.1.1) and including stillages, pallets, frails fixed to vehicles, inloader vehicles, specific glass-securing devices, stanchions and vacuum-lifting devices which are used for road transport and on building sites. 1.2 Specific hazards due to the use inside the factory are dealt with in EN 13035-1. 1.3 This standard deals only with the devices which are directly in contact with the glass. This standard does not apply to manual handling equipment such as carrying straps and vacuum pads. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass. This European Standard does not apply to equipment for the transport by other ways than on road e.g. by ship or train, and the transportation of glazed windows/frames. 1.4 This standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard. 1.5 This document is not applicable to storage, handling or transportation equipment for flat glass outside the factory, which is manufactured before the date of its publication as EN.

Machines and plants for the manufacture, treatment and processing of flat glass — Safety requirements — Part 2: Storage, handling and transportation equipment outside the factory