玻璃和陶瓷生产设备标准-分析测试百科网

EN 13035-4:2003 平板玻璃的制造,处理和加工用机械和设备.安全要求.第4部分:倾斜台;包含修改件A1-2009

This standard containsThe requirements for safety forThe design and installation of tilting tables; whereThe flat glass is brought fromThe horizontal almost toThe vertical position or vice versa by lying on or-supported atThe lower edge-leaning against a supporting surface.This standard deals with all significant hazards; hazardous situations and events relevant to tilting tables for flat glass; whenThey are used as intended and underThe conditions of misuse which are reasonably foreseeable byThe manufacturer (see Clause 4).This standard specifies the appropriate technical measures to eliminate or reduce risks arising fromThe significant hazards during commissioning; operation and maintenance. Noise is not a significant hazard forThis type of machines.This standard is not applicable to tilting tables where all movements are done by human power.This standard is not applicable to additional equipment; e. g. for cutting (see EN 13035-3); loading and unloading (see EN 13035-5); break-out (see EN 13035-6); transporting (see EN 619) of flat glass as used as integral parts of the machinery. IfThere are specific risks that arise in connection with tilting tables; appropriate measures are specified.This document is not applicable to tilting tables which are manufactured beforeThe date of publication of this document by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 4: Tilting tables (Incorporates Amendment A1: 2009)

ICS: 81.100
CCS
发布: 2003-07-23
实施

BS EN 13035-4:2003 平板玻璃的制造、处理和加工用机械和设备.安全要求.倾斜台

1 This standard contains the requirements for safety for the design and installation of tilting tables, where the flat glass is brought from the horizontal almost to the vertical position or vice versa by lying on or - supported at the lower edge - leaning against a supporting surface. 2 This standard deals with all significant hazards, hazardous situations and events relevant to tilting tables for flat glass, when they are used as intended and under the conditions foreseeable by the manufacturer (see clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks which can arise from these significant hazards. 3 This standard is not applicable to tilting tables where all movements are done by human power. 4 This standard is not applicable to additional equipment, e.g. for cutting (see prEN 13035-3), loading and unloading (see prEN 13035-5), break-out (see prEN 13035-6), transporting (see EN 619) of flat glass as used as integral parts of the machinery. If there are specific risks that arise in connection with tilting tables, appropriate measures are specified. 5 This document is not applicable to tilting tables which are manufactured before the date of publication of this document by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Tilting tables

ICS: 81.100
CCS: Q93
发布: 2003-07-23
实施: 2003-07-23

BS EN 13035-3:2003 平板玻璃的制造、处理和加工用机械和设备.安全要求.切割机

1 This standard contains the requirements for safety for the design and installation of machines with one movable bridge for cutting of flat glass, which operate by scoring of the glass placed on a horizontal support. This standard covers the transport of the glass on the machine. 2 This standard deals with all significant hazards, hazardous situations and events relevant to flat glass cutting machines, when they are used as intended and under the conditions foreseeable by the manufacturer (see clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks which can arise from these significant hazards. Hazards from noise are not considered to be significant. 3 This standard does not apply to flat glass cutting by abrasive cutting or by the use of high pressure liquid or lasers. 4 This standard does not apply to loading and unloading of flat glass on to or from cutting machines and the breaking out (see prEN 13035-5 and prEN 13035-6). 5 This standard does not apply to conveyors (see EN 619) and fans as used as integral parts of the machinery. If there are specific risks that arise in connection with flat glass cutting machines, appropriate measures are specified. 6 This standard does not apply to cutting of laminated glass (see prEN 13035-7). 7 This standard does not apply to cutting while the glass is moving. 8 This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Cutting machines

ICS: 81.100
CCS: Q93
发布: 2003-07-23
实施: 2003-07-23

EN 13035-3:2003 平板玻璃的制造,处理和加工用机械和设备.安全要求.第3部分:切割机.包含修改件A1-2009;合并勘误表-2010年4月

This standard contains the requirements for safety for the design and installation of machines with one movable bridge for cutting of flat glass, which operate by scoring of the glass placed on a horizontal support.This standard covers the transport of the glass on the machine.This European Standard deals with all significant hazards, hazardous situations and events relevant to flat glass cutting machines, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance.This standard does not apply to flat glass cutting by abrasive cutting or by the use of high pressure liquid or lasers.This standard does not apply to loading and unloading of flat glass on to or from cutting machines and the breaking out (see EN 13035-5 and EN 13035-6).This standard does not apply to conveyors (see EN 619) and fans as used as integral parts of the machinery. If there are specific risks that arise in connection with flat glass cutting machines, appropriate measures are specified.This standard does not apply to cutting of laminated glass (see EN 13035-7).This standard does not apply to cutting while the glass is moving.This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 3: Cutting machines (Incorporates Amendment A1: 2009; Incorporating corrigendum April 2010)

ICS: 81.100
CCS
发布: 2003-07-01
实施

EN 13042-5:2003 空心玻璃生产,处理和加工用机械和设备.安全要求.第5部分:压力机.包含修改件A1-2009

This standard contains the requirements for the design and installation of glass presses including equipment for feeding of portions of molten glass to the mould, loading equipment and equipment for discharging articles (take-out) when these are integral parts of the presses. !This standard deals with all significant hazards, hazardous situations and events relevant to glass presses when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance."This standard does not deal with forming machines for hollow glass where the press operation is only a part of the hot-forming process, such as the press/blow process of IS machines (see !EN 13042-3").This standard does not deal with gob feeders (see !EN 13042-1") and handling machines for feeding (see !EN 13042-2") which are self-standing machines and dealt with in other standards of the series regarding machinery used in the production of hollow glass.This document is not applicable to presses which are manufactured before the date of publication of this document by CEN.This standard deals only with hazards arising from the application of components which may be used in glass presses, such as motors and continuous handling equipment. More particular safety requirements are dealt with within standards more specific to that component, including noise.This standard does not deal with equipment for cooling and waste ejection with air or heating from an outside system.

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 5: Presses (Incorporates Amendment A1: 2009)

ICS: 81.100
CCS
发布: 2003-07-01
实施