75.200 石油、石油产品和天然气储运设备 标准查询与下载

ISO/DIS 4437-3.2:2023 供应气体燃料的塑料管道系统 聚乙烯 (PE) 第 3 部分：管件

Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 3: Fittings

ISO/DIS 4437-5.2:2023 供应气体燃料的塑料管道系统 聚乙烯 (PE) 第 5 部分：系统用途的适用性

Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 5: Fitness for purpose of the system

ISO/DIS 21809-2:2023 石油和天然气工业 管道运输系统中使用的埋地或水下管道的外部涂层 第 2 部分：单层熔结环氧涂层

Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Single layer fusion-bonded epoxy coatings

ISO/DIS 4437-1.2:2023 供应气体燃料的塑料管道系统 聚乙烯 (PE) 第 1 部分：概述

Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 1: General

ISO 13623:2017/DAmd 1 石油和天然气工业 管道运输系统 修订1：含二氧化碳或氢气流体运输的补充要求

Petroleum and natural gas industries — Pipeline transportation systems — Amendment 1: Complementary requirements for the transportation of fluids containing carbon dioxide or hydrogen

ISO 22974:2023 石油天然气工业 管道运输系统 管道完整性评价规范

Petroleum and natural gas industry — Pipeline transportation systems — Pipeline integrity assessment specification

ISO/DIS 4437-2.2:2023 供应气体燃料的塑料管道系统 聚乙烯 (PE) 第 2 部分：管道

Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 2: Pipes

T/XJPCIA 0002-2023 油气集输非金属管道不动火（带压）抢维修工艺技术规范

      本文件规定了油气集输非金属管道不动火（带压）抢维修工艺的术语和定义、不动火（带压）抢维修作业范围、卡具通用要求、施工前的准备、不动火带压堵漏工艺、不动火带压开孔工艺、不动火连接工艺和合格判定的要求。       本文件适用于设计压力不大于16 MPa、设计温度为-20 ℃～120 ℃的陆上油田集输非钢质管道新建、改建和扩建的工程施工。

Technical specification for non-hotwork repairing (with pressure) of oil and gas gathering and transportation non-metal pipelines

T/XJPCIA 0001-2023 油气集输金属管道不动火（带压）抢维修工艺技术规范

       本文件规定了油气集输金属管道不动火（带压）抢维修工艺的术语和定义、不动火（带压）抢维修作业范围、卡具通用要求、施工前的准备、不动火带压堵漏工艺、不动火带压开孔工艺、不动火连接工艺的要求。        本文件适用于油气集输金属管道中利用注剂槽式密封卡具（以下简称“卡具”）进行不动火（带压）堵漏、开孔、连接的抢维修及改扩建工程施工作业。设计压力不大于35 MPa、设计温度为-20 ℃～360 ℃的陆上油田集输钢质管道和设计压力不大于70 MPa的陆上气田集输钢质管道新建、改建和扩建的工程施工。

Technical specification for non-hotwork repairing (with pressure) of oil and gas gathering and transportation metal pipelines

ISO/TS 16486-7:2023 供应气体燃料的塑料管道系统 带熔接和机械连接的未塑化聚酰胺（PA-U）管道系统 第 7 部分：合格评定

Plastics piping systems for the supply of gaseous fuels — Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing — Part 7: Assessment of conformity

EN 14870-4 石油和天然气工业 管道输送系统的感应弯头、管件和法兰 第4部分：工厂冷弯（ISO 15590-4:2019，已修改）

This document specifies the technical delivery conditions for bends made by the cold bending process for bend with radii 5xOD or higher for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. Short radius factory cold bends should not be used for pipeline. NOTE 1 ISO 13623 is modified adopted as EN 14161 to exclude on-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances. This document also specifies the requirements for the manufacture of two product specification levels (PSLs) of cold bends corresponding to product specification levels given for pipe in ISO 3183. This document is applicable to cold bends made from seamless and welded pipe of unalloyed or low-alloy steels. NOTE 2 These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183. This document is not applicable to the selection of the cold bend product specification level. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements. NOTE 3 See also ISO 3183:2012, Introduction. This document is not applicable to field cold bends and pipeline bends made by other manufacturing processes. On-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances are excluded from the scope of this document.

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 4: Factory cold bends (ISO 15590-4:2019, modified)

EN 14870-1 石油和天然气工业 管道输送系统用感应弯头、管件和法兰 第1部分：感应弯头（ISO 15590-1:2018，已修改）

This document specifies the technical delivery conditions for bends made by the induction bending process for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. NOTE 1 ISO 13623 is modified adopted as EN 14161 to exclude on-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances. This document is applicable to induction bends made from seamless and welded pipe of unalloyed or low-alloy steels. NOTE 2 These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183. This document specifies the requirements for the manufacture of two product specification levels (PSLs) of induction bends corresponding to product specification levels given for pipe in ISO 3183:2012. This document is not applicable to the selection of the induction bend PSL. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements; see also ISO 3183, Introduction. This document is not applicable to pipeline bends made by other manufacturing processes. On-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances are excluded from the scope of this document.

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2018, modified)

GSO ISO 21857:2023 石油、石化和天然气工业 防止杂散电流影响的管道系统腐蚀

This document establishes the general principles for the evaluation and minimization of the effects of stray current corrosion on external surfaces of buried or immersed pipeline systems caused by AC and DC electrical interference. Other stray current effects such as overheating, and interference with welding operations are not covered in this document. A brief description of AC effects, general principles and some guidelines, are provided. NOTE 1 See ISO 18086 for the effects of alternating current on buried or immersed pipelines. Systems that can also be affected by stray currents include buried or immersed metal structures such as the following: a) pipeline systems; b) metal sheathed cables; c) tanks and vessels; d) earthing systems; e) steel reinforcement in concrete; f) sheet steel piling. This document gives guidelines for — the design of cathodic protection systems that might produce stray currents, — the design of pipeline systems, or elements of pipeline systems, which are buried or immersed, and which can be subject to stray current corrosion, and — the selection of appropriate protection or mitigation measures. Internal corrosion risks from stray currents are not dealt with in detail in this document but principles and measures described here can be applicable for minimizing the interference effects. NOTE 2 The impact of electromagnetic interference on above-ground appurtenances of pipeline systems is covered in EN 50443, IEC 61140, IEC 60364-4-41, IEC 60479-1, IEC 60364-5-52, IEC/TS 61201 and IEC/TR 60479-5. This document can also be used for pipeline systems outside of the petrochemical and natural gas industries and other buried or immersed structures. NOTE 3 EN 50162 provides guidance for railway related structures.

Petroleum, petrochemical and natural gas industries — Prevention of corrosion on pipeline systems influenced by stray currents

GSO ISO 3183:2023 石油天然气工业管道输送系统用钢管

This document specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries. This document supplements API Spec 5L, 46th edition (2018), the requirements of which are applicable with the exceptions specified in this document. This document is not applicable to cast pipe.

Petroleum and natural gas industries — Steel pipe for pipeline transportation systems

GSO ISO 15590-4:2023 石油和天然气工业 管道运输系统用工厂弯管、配件和法兰 第4部分：工厂冷弯管

This document specifies the technical delivery conditions for bends made by the cold bending process for bend with radii 5xOD or higher for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This document also specifies the requirements for the manufacture of two product specification levels (PSLs) of cold bends corresponding to product specification levels given for pipe in ISO 3183. This document is applicable to cold bends made from seamless and welded pipe of unalloyed or low-alloy steels. NOTE 1 These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183. This document is not applicable to the selection of the cold bend product specification level. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements. NOTE 2 See also ISO 3183:2012, Introduction. This document is not applicable to field cold bends and pipeline bends made by other manufacturing processes.

Petroleum and natural gas industries — Factory bends, fittings and flanges for pipeline transportation systems — Part 4: Factory cold bends

GSO ISO 20257-1:2023 液化天然气装置和设备 浮式液化天然气装置的设计 第1部分：一般要求

This document provides requirements and guidance for the design and operation of floating liquefied natural gas (LNG) installations, including installations for the liquefaction, storage, vaporisation, transfer and handling of LNG, in order to have a safe and environmentally acceptable design and operation of floating LNG installations. This document is applicable to: — floating LNG liquefaction installations (plant) — FLNG; — floating LNG regasification installations (plant) — FSRU; — floating storage units — FSU. This document is applicable to offshore, near-shore or docked floating LNG installations. This document includes any jetty in the scope in case of docked floating LNG installations with regards to the mooring. This document briefly describes floating LNG mooring concepts. This document is applicable to both newbuilt and converted floating LNG installations, and addresses specific requirements. This document is not applicable to: — onshore LNG storage, liquefaction and/or regasification installations/plants, except for docked FSRU and/or FLNG installations; — offshore LNG plants based on non-floating structure (such as gravity based structure [GBS] principle); and — support onshore based facilities (such as support vessels, tugs, etc.). This document is not intended for design floating power generation facilities though relevant parts of this document can be used. This document is not intended to cover LNG as fuel bunkering applications.

Installation and equipment for liquefied natural gas — Design of floating LNG installations — Part 1: General requirements

GSO ISO 20257-2:2023 液化天然气安装和设备 浮式液化天然气装置的设计 第2部分：具体 FSRU 问题

This document provides specific requirements and guidance for the design and operation of floating LNG storage and regasification units (FSRU) described in ISO 20257-1. This document is applicable to offshore, near-shore or docked FSRUs and to both new-built and converted FSRUs. This document includes requirements to the jetty when an FSRU is moored to a jetty.

Installation and equipment for liquefied natural gas — Design of floating LNG installations — Part 2: Specific FSRU issues

BS EN 1474-2:2020 液化天然气安装和设备 船舶输送系统的设计和测试 输送软管的设计和测试

Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems - Design and testing of transfer hoses

BS ISO 24139-2:2023 石油和天然气工业 管道输送系统用耐腐蚀合金复合弯头和管件 复合管件

1   Scope This document specifies the technical delivery conditions regarding design, geometric dimensions, materials, manufacturing procedures, inspection methods, non-destructive testing, marking, package and storage for factory-made, seamless and welded, corrosion resistant alloy ( CRA ) clad fittings for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This document is applicable to CRA clad fittings for use in transportation or process pipelines transporting corrosive media-containing single-phase or multi-phase fluid such as oil, gas and water for the petroleum and natural gas industries. It can also be used as reference in other fields. The clad fittings specified in this document include clad elbows, clad reducers, clad tees and clad caps. Two technical delivery conditions classes for clad fittings are designated. Class B provides a standard quality level for clad fittings and Class S provides technical requirements for sour-service conditions. Fabricated laterals, fabricated lap joint stub ends and other fittings employing circumferential or intersection welds are considered as pipe fabrication and are outside the scope of this document.

Petroleum and natural gas industries. Corrosion resistant alloy clad bends and fittings for pipeline transportation system - Clad fittings

ISO 24139-2:2023 石油和天然气工业.管道运输系统用耐腐蚀合金复合弯管和配件.第2部分：复合配件

This document specifies the technical delivery conditions regarding design, geometric dimensions, materials, manufacturing procedures, inspection methods, non-destructive testing, marking, package and storage for factory-made, seamless and welded, corrosion resistant alloy (CRA) clad fittings for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This document is applicable to CRA clad fittings for use in transportation or process pipelines transporting corrosive media-containing single-phase or multi-phase fluid such as oil, gas and water for the petroleum and natural gas industries. It can also be used as reference in other fields. The clad fittings specified in this document include clad elbows, clad reducers, clad tees and clad caps. Two technical delivery conditions classes for clad fittings are designated. Class B provides a standard quality level for clad fittings and Class S provides technical requirements for sour-service conditions. Fabricated laterals, fabricated lap joint stub ends and other fittings employing circumferential or intersection welds are considered as pipe fabrication and are outside the scope of this document.

Petroleum and natural gas industries — Corrosion resistant alloy clad bends and fittings for pipeline transportation system — Part 2: Clad fittings