75.200 石油、石油产品和天然气储运设备 标准查询与下载

22/30437648 DC BS EN ISO 22974 石油和天然气工业 管道完整性评估规范

BS EN ISO 22974. Petroleum and natural gas industries. Pipeline integrity assessment specification

ISO/TS 10839:2022 气体燃料供应用聚乙烯管和配件.设计、搬运和安装实施规程

Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation

KS B ISO 15590-1-2022 石油和天然气工业.管道输送系统用感应弯管、配件和法兰.第1部分:感应弯管

Petroleum and natural gas industries — Induction bends, fittings and flanges for pipeline transportation systems —Part 1: Induction bends

KS B ISO 15590-1:2022 石油和天然气工业.管道输送系统用感应弯管、配件和法兰.第1部分:感应弯管

Petroleum and natural gas industries — Induction bends, fittings and flanges for pipeline transportation systems —Part 1: Induction bends

GSO ISO 19345-2:2022 石油天然气工业 管道运输系统 管道完整性管理规范 第2部分：海上管道全生命周期完整性管理

This document specifies requirements and gives recommendations on the management of integrity of a pipeline system throughout its life cycle, which includes design, construction, commissioning, operation, maintenance and abandonment. This document is applicable to offshore pipelines for transporting petroleum and natural gas. It is applicable to rigid steel pipelines. It is not applicable to flexible pipelines, dynamic risers or those constructed from other materials, such as glass-reinforced plastics. NOTE 1 An offshore pipeline system extends to: — the first valve, flange or connection above water on platform or subsea mechanical connector with subsea structure (i.e. manifold or dynamic riser); — the connection point to the offshore installation (i.e. piping manifolds are not included); — the first valve, flange, connection or isolation joint at a landfall, unless otherwise specified by the onshore legislation. NOTE 2 The components mentioned above (valve, flange, connection, isolation joint) include also any pup pieces, i.e. the offshore pipeline system extends to the weld beyond the pup piece, see Figure 1. This document is used for integrity management, which is initiated at the design and construction stage of the pipeline. Where requirements of a design and construction standard (e.g. ISO 13623) are different, the provisions of this document will enhance the design and construction from an integrity perspective.

Petroleum and natural gas industry — Pipeline transportation systems — Pipeline integrity management specification — Part 2: Full-life cycle integrity management for offshore pipeline

GSO ISO 19345-1:2022 石油天然气工业 管道运输系统 管道完整性管理规范 第1部分：陆上管道全生命周期完整性管理

1.1 This document specifies requirements and gives recommendations on the management of integrity of a pipeline system throughout its life cycle which includes design, construction, commissioning, operation, maintenance and abandonment. 1.2 This document is applicable to onshore pipeline systems used in transportation in the petroleum and natural gas industries, connecting wells, production plants, process plants, refineries and storage facilities, including any section of a pipeline constructed within the boundaries of such facilities for connection purposes. The extent of pipeline systems covered by this document is illustrated in Figure 1. This document does not deal specifically with the integrity of non-pipe elements. The pipeline segment between the wellsite and the gathering station, treatment plant or process plant (between Facilities 1 and 2 in Figure 1) is included in this document, though many mandatory elements of this document are not practical due to characteristics such as diameter, operating parameters, etc. 1.3 This document applies to rigid, steel pipelines. It is not applicable for flexible pipelines or those constructed from other materials, such as glass-reinforced plastics. 1.4 This document does not cover all conditions nor engineers' competency which might be related to pipeline integrity. The user can evaluate whether additional requirements are necessary. 1.5 This document is used for integrity management, which is initiated at the design and construction stage of the pipeline. Where requirements of a design and construction standard (e.g. ISO 13623) are different, the provisions of this document will enhance the design and construction from an integrity perspective.

Petroleum and natural gas industry — Pipeline transportation systems — Pipeline integrity management specification — Part 1: Full-life cycle integrity management for onshore pipeline

ASTM D6849-22 液化石油气试验方法用样品瓶中液化石油气（LPG）的储存和使用的标准实施规程

1.1 This practice covers information for the storage and use of LPG samples in standard cylinders of the type used in sampling method, Practice D1265 and floating piston cylinders used in sampling method, Practice D3700. 1.2 This practice is especially applicable when the LPG sample is used as a quality control (QC) reference material for LPG test methods, such as gas chromatography (GC) analysis (Test Method D2163) or vapor pressure (Test Method D6897) that use only a few mL per test, since relatively small portable Department of Transportation (DOT) cylinders (for example, 20 lb common barbecue cylinders, or common Mower/Forklift cylinders) can be used. 1.2.1 Modification of the pressure relief (QCC1) valve on single access port cylinders may prohibit the collection or transport of cylinders outside of permitted facilities such as refineries, gas plants or pipeline stations. No modification is generally required for multi-port mower/forklift cylinders that have a separate access port for pressure relief and additional access ports for filling, liquid/vapor withdrawal or liquid level indication. Consult the Authority having Jurisdiction for detailed regional regulatory requirements for transport of LPG in pressurized cylinders. 1.3 This practice can be applied to other test methods. However, test methods that require a large amount of sample per test (for example, manual vapor pressure Test Method D1267) will require QC volumes in excess of 1000 L if stored in standard DOT cylinders or American Society of Mechanical Engineers (ASME) vessels. 1.3.1 Test methods for trace materials that may be sensitive to vessel surfaces (for example H2O, H2S/sulfur, or trace residues) could preferably use aluminum, stainless steel or internally coated vessels to minimize surface absorption/ reaction or larger vessels to minimize surface/volume ratio. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Storage and Use of Liquefied Petroleum Gases (LPG) in Sample Cylinders for LPG Test Methods

BS ISO 15590-3:2022 石油和天然气工业 用于管道运输系统的工厂弯管、配件和法兰 法兰

What is ISO 15590-3 - Flanges for pipeline transportation systems about?   ISO 15590-3 is an international standard that covers flanges for pipeline transportation systems to enable easy access to pipelines for repair and maintenance.   ISO 15590-3 specifies the technical requirements for carbon steel and low-alloy steel forged flanges for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623 .   ISO 15590-3 applies to weld neck and blind flanges (full face, raised face, and RTJ groove) as well as anchor, swivel-ring flanges and orifice flanges.   ISO 15590-3 designates those categories of flanges that meet the industry's need to match ISO 3183 pipe. These flanges are for normal and low-temperature service and include supplementary requirements where required for sour service.

Petroleum and natural gas industries. Factory bends, fittings and flanges for pipeline transportation systems - Flanges

ASTM E2942-22 符合泄漏预防、控制和对策计划（SPCC）法规的罐区设施安全标准指南

1.1 This guide covers fencing and lighting only. More sophisticated security systems may be appropriate for the facility but discussion of these types of systems is beyond the scope of this document. 1.2 The information included in this guide is intended for petroleum bulk storage facilities. It is not intended for use with retail fueling and other motor fueling facilities, refineries, chemical plants, docks, oil production facilities, or electric power generation, transmission, distribution and service center facilities. Fencing, lighting or other security measures designed to prevent unauthorized access to the bulk storage facility may be components of Best Management Practices (BMPs) that the facility uses to prevent releases of petroleum to storm water discharges. There are several different types of fencing and lighting that can be effective. The intent of this document is to outline a method for providing security fencing and lighting that has been effectively used. There are other fencing and lighting methods that may be adequately effective. Some facilities may be considered adequately secure without fencing or lighting. An analysis of the threat level should be made to determine the type of security system to employ. 1.3 Any facilities must meet local, state, and federal building, architectural, hazardous material handling and storage, and fire protection codes. 1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 This test method is under the jurisdiction of ASTM Committee E50 on Environmental Assessment, Risk Management and Corrective Action and is the direct responsibility of Subcommittee E50.01 on Storage Tanks. Current edition approved April 1, 2022. Published May 2022. Originally approved in 2015. Last previous edition approved in 2017 as E2942–17. DOI: 10.1520/E2942–22 *A Summary of Changes section appears at the end of this standard Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 2. Referenced Documents

Standard Guide for Security of Tank Farm Installations for Compliance with Spill Prevention, Control and Countermeasure Plan (SPCC) Regulations

ISO 15590-3:2022 石油和天然气工业.管道运输系统用工厂弯头、配件和法兰.第3部分:法兰

This document specifies the technical requirements for carbon steel and low-alloy steel forged flanges for use in pipeline transportation systems for the petroleum and natural gas industries as defined in This document applies to weldneck and blind flanges (full face, raised face, and RTJ groove) as well as anchor, swivel-ring flanges and orifice flanges. This document designates those categories of flanges that meet the industry's need to match requirements where required for sour service. Materials for, or the attachment of, factory-welded extensions, bolting materials, gaskets, slip-on flanges or flanged fittings are not covered by this document. This document is not applicable to integrally cast or forged flanges for valves, pumps or other equipment. This document does not cover the selection of the flange category or pressure class. Sizes and pressure classes listed in ISO 7005-1 and applicable to this document are as follows: — DN 10 (NPS 1/2) to DN 1500 (NPS 60); — PN 20 (class 150), PN 50 (class 300), PN 100 (class 600), PN 150 (class 900), PN 250 (class 1500), PN 420 (class 2500).

Petroleum and natural gas industries — Factory bends, fittings and flanges for pipeline transportation systems — Part 3: Flanges

22/30450627 DC BS EN ISO 16961 石油、石化和天然气工业 钢制储罐的内涂层和衬里

BS EN ISO 16961. Petroleum, petrochemical and natural gas industries. Internal coating and lining of steel storage tanks

T/HATSI 0017-2022 油气管道换管作业消磁技术规范

本文件规定了油气管道直流消磁和交直流消磁的适用情况、设备结构及要求、作业流程、作业要求 等内容。 本文件适用于油气管道换管作业的消磁操作。

Technical specification for degaussing of oil and gas pipeline replacement operations

ISO/TS 12835:2022 热井套管连接的鉴定

Qualification of casing connections for thermal wells

T/CAGDE 208-2022 石油化工在线分析仪表维护保运作业规范

本团体标准的范围主要包括石油化工在线分析仪表维保产品相关的术语和定义、使用管理等。本标准适用石油化工在线分析仪表维保。主要技术内容如下： 1、标准范围。本标准适用于石油化工行业在线分析仪表维护保运作业规范的基本要求、作业内容、作业要求、目标及安全措施。本文件适用于石油化工行业在线分析仪表的维护保运作业。 2、术语和定义。本标准对标准中涉及到的相关术语进行了解释和定义。 3、基本要求。本标准提出机构要求、人员要求等方面的技术要求。 4、作业内容。本标准提出日常工作、巡回检查等方面的技术要求。 5、目标与安全措施等方面的技术要求。

Specifications for Maintenance and Operation of On-line Analytical Instruments in Petrochemical Industry

T/CAGDE 209-2022 石油化工在线分析仪表检修作业规范

本团体标准的范围主要包括石油化工在线分析仪表检修相关的术语和定义、准备工作、检修作业、在线分析仪的调试校验、质量验收等。本标准适用于石油化工在线分析仪表检修。主要技术内容如下： 1.标准范围。本标准适用于石油化工在线分析仪表检修的要求。本标准适用于石油化工行业在线分析仪表检修的准备工作、检修作业及质量验收，石油化工行业生产过程中对检测、控制等在线分析仪表的检修作业。    2.术语和定义。本标准对标准中涉及到的相关术语进行了解释和定义。    3.准备工作。本标准提出人员配备、技术准备、机具准备、检测仪表准备等方面的技术要求。    4.检修作业。本标准提出确定维修等级、检修过程、样品管路清理、主要部件清洗、样品预处理检修、主要部件的检测与更换、预处理系统及主要部件的回装、在线分析系统的密闭性检查、在线分析仪的调试校验等方面的技术要求    5.质量验收。本标准提出产品质量验收处理方法，质量验收制度、质量验收仪表、联锁保护系统、安全仪表系统和重要的控制系统、仪表及控制系统检修资料、仪表检修记录的内容、经过更改的仪表及系统并进行验收存档。 本标准将上述技术内容进行了有机的整合，形成一套完整、规范、合理的石油化工在线分析仪表检修标准。

Specifications for inspection and maintenance of on-line analytical instruments in petrochemical industry

CSA/ANSI Z21.24:22 • CSA 6.10-2022 燃气器具连接器

1 Scope 1.1 Inclusions This Standard applies to newly produced gas appliance connectors, constructed entirely of new unused parts and materials, having nominal internal diameters of 1/4, 3/8, 1/2, 5/8, 3/4, and 1 in, and having fittings at both ends provided with taper pipe threads for connection to a gas appliance and to house piping. This Standard covers assembled appliance connectors not exceeding a nominal length of 6 ft (1.83 m). Connectors listed under this Standard are intended for use with gas appliances that are not frequently moved after installation. For the purpose of this Standard, an unused connector, including end fittings, is considered to be a connector that has not been installed. 1.2 Suitability Appliance connectors complying with this Standard are considered suitable for use with natural gases and propane. 1.3 System pressure units Appliance connectors complying with this Standard are for use with piping systems having fuel gas pressures not in excess of 1/2 psi (3.5 kPa). 1.4 Measurement units This Standard contains SI (metric) corresponding to the yard/pound quantities, the purpose being to allow the Standard to be used in SI (metric) units. (IEEE/ASTM SI 10 or CAN/CSA Z234.1 are used as a guide in making metric conversion from yard/pound quantities.) The values given in parentheses are for information and comparison only. 1.5 References to “psi” All references to “psi” throughout this Standard are gauge pressure unless otherwise specified. 1.6 Provisions unique to the United States Clause 7contains provisions that are unique to the United States. 1.7 Provisions unique to Canada Clause 8contains provisions that are unique to Canada. 1.8 Mandatory language In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Connectors for gas appliances

EN ISO 16486-4:2022 供应气体燃料用塑料管系统. 带熔接连接和机械连接的未增塑聚酰胺 (PA-U) 管系统. 第4部分: 阀门

This document specifies the characteristics of valves made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PA-U pipes or fittings conforming to ISO 16486-2 and ISO 16486-3 respectively. Valves made from material other than unplasticized polyamide designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PA-U piping systems according to the ISO 16486 series provided they have relevant PA-U connections for butt fusion or electrofusion ends (see ISO 16486-3). The component, i.e. the complete valve, is required to fulfil the requirements of this document. This document also specifies the test parameters for the test methods it describes. In conjunction with ISO 16486-1, ISO 16486-2, ISO 16486-3 and ISO 16486-5, this document is applicable to PA-U valves and their joints and to joints with components of PA-U and other materials intended to be used under the following conditions: a) a maximum operating pressure (MOP) of up to and including 18 bar[1], or limited to 16 bar under regional CEN requirements, at a reference temperature of 20 °C for design purposes; NOTE 1 For the purpose of this document and the references to ISO 8233, MOP is considered to be nominal pressure. b) an operating temperature of −20 °C to 40 °C; NOTE 2 For operating temperatures between 20 °C and 40 °C, derating coefficients are specified in ISO 16486-5. This document covers valves for pipes with a nominal outside diameter, dn, ≤ 400 mm. [1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm².

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves (ISO 16486-4:2022)

JIS K 6775-2:2022 供应气体燃料的聚乙烯管件 第2部分：套管接头

Polyethylene pipe-fittings for the supply of gaseous fuels -- Part 2: Spigot fittings

JIS K 6775-3:2022 供应气体燃料的聚乙烯管件 第3部分：电熔管件

Polyethylene pipe-fittings for the supply of gaseous fuels -- Part 3: Electrofusion fittings

JIS K 6774:2022 供应气体燃料的聚乙烯管

Polyethylene pipes for the supply of gaseous fuels