75.200 石油、石油产品和天然气储运设备 标准查询与下载

CSA/ANSI NGV 5.2-2023 车辆加油装置（VFA）

1 Scope 1.1 General This Standard details mechanical, physical, and electrical requirements for a newly manufactured appliance that compresses natural gas for vehicles and dispenses directly into a) the vehicle natural gas fuel storage system, referred to as a vehicle fuelling appliance (VFA); or b) the vehicle’s activated carbon adsorbents-based adsorbed natural gas (ANG) fuel storage system, referred to as a vehicle fuelling appliance (VFA). This Standard applies to appliances that incorporate compression and dispensing in the same appliance. Notes: 1) Residential fuelling appliances (RFA) are addressed in CSA/ANSI NGV 5.1. 2) Devices dedicated only to dispensing fuel into vehicles are addressed in CSA/ANSI NGV 4.1. 1.2 Application This Standard applies to all appliances that are a) intended for natural gas only (see Clause 1.1); b) intended for outdoor or indoor installation; c) intended for ambient temperatures not below -40 °C (-40 °F); d) intended for nominal voltage not exceeding 480 V AC; e) certified as a system with temperature compensated pressure limits for delivery of fuel for i) direct fuelling of vehicles; ii) fuelling of vehicles from the system’s internal storage; iii) filling of external natural gas storage systems; or iv) any combination of the above; f) equipped with maximum inlet flow rate not exceeding 10 SCFM (17 SCMH); g) for installation in non-residential occupancies; h) intended to meet installation fire safety requirements in accordance with the requirements of the applicable Code; i) for connection to a single vehicle, multiple vehicles, or storage systems; j) intended for installation in non-hazardous locations; k) for connection to a single or multiple vehicle storage system or external storage systems, with no single storage system having a total capacity of less than 80 L water volume; and l) intended for installation in accordance with NFPA 52 or CSA B108.1 where not in conflict with the requirements in this document. These requirements apply only to ANG appliances for use with vehicle or external fuel storage systems that contain activated carbon-adsorbent material with an MDP/RCP ratio less than or equal to 1.5, and that have a service pressure of 6205 kPa (900 psig). 1.3 Pressure references All references to “kPa” and “psig” throughout this Standard are to be considered gauge pressures unless otherwise specified. 1.4 Resolution of conflicts In the case of conflict between this Standard and federal, national, provincial/territorial, state, or local requirements, the requirements of the authority having jurisdiction take precedence. 1.5 Units of measure This Standard contains SI (metric) units corresponding to the inch/pound quantities, the purpose being to allow the Standard to be used in SI (metric) units. If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, then the first stated unit or both are to be provided. Note: IEEE/ASTM SI 10 or ISO 80000-1 is used as a guide in making metric conversion from inch/pound quantities. 1.6 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.7 Alternate construction The requirements of this Standard are not intended to constrain innovation. When considering fuels, materials, designs, or constructions not specifically dealt with in this Standard, these alternatives may be evaluated as to their ability to yield levels of safety and performance equivalent to those prescribed by this Standard.

Vehicle fuelling appliances (VFA)

T/CCSAS 019-2022 加氢站、油气氢合建站安全规范

Safety specifications for hydrogen refueling stations and oil-gas-hydrogen co-construction stations

T/CCSAS 018-2022 加氢站氢运输及配送安全技术规范

Safety Technical Specifications for Hydrogen Transportation and Distribution of Hydrogen Refueling Stations

KS B ISO 15590-3:2022 石油和天然气工业.管道运输系统用工厂弯管、管件和法兰.第3部分:法兰

Petroleum and natural gas industries — Factory bends, fittings and flanges for pipeline transportation systems — Part 3: Flanges

KS B ISO 15590-3-2022 石油和天然气工业.管道运输系统用工厂弯管、管件和法兰.第3部分:法兰

Petroleum and natural gas industries — Factory bends, fittings and flanges for pipeline transportation systems — Part 3: Flanges

KS B ISO 15590-2-2022 石油和天然气工业.管道运输系统用工厂弯管、配件和法兰.第2部分:配件

Petroleum and natural gas industries — Factory bends, fittings and flanges for pipeline transportation systems — Part 2: Fittings

KS B ISO 15590-2:2022 石油和天然气工业.管道运输系统用工厂弯管、配件和法兰.第2部分:配件

Petroleum and natural gas industries — Factory bends, fittings and flanges for pipeline transportation systems — Part 2: Fittings

CSA/ANSI NGV 1-2022 压缩天然气汽车 (NGV) 加油连接装置

1 Scope 1.1 Applicability This Standard applies to newly produced compressed natural gas vehicle (NGV) fuelling connection devices, hereinafter referred to as “devices”, constructed entirely of new, unused parts and materials. NGV fuelling connection devices consist of the following components, as applicable: a) receptacle and protective cap (mounted on vehicle) (see Clause 4.4); b) nozzle (see Clause 4.2); and c) three-way valve (external to nozzle and mounted in the fuel dispenser system) (see Clause 4.5). Note: P36HD nozzles designed in accordance with this Standard will not be compatible with existing P36 heavy duty applications using C200 (ISO 14469) receptacles, equivalent to P30HD (see Figure 6). 1.2 Applicable pressures This Standard applies to devices that have a service pressure of either 6205 kPa (900 psi), 16 500 kPa (2400 psi), 20 700 kPa (3000 psi), or 24 800 kPa (3600 psi), hereinafter referred to in this Standard as the following [see Clause 4.8.3c)]: a) “P9”: 6205 kPa (900 psi); b) “P24”: 16 500 kPa (2400 psi); c) “P30” and “P30HD”: 20 700 kPa (3000 psi); and d) “P36” and “P36HD”: 24 800 kPa (3600 psi). The “HD” suffix designates a larger geometry version to allow higher flow rates associated with fuelling larger heavy duty applications. Legacy connection devices produced prior to the 2017 edition of this Standard used the P30 HD profile only (see Figure 6). 1.3 Mating components This Standard applies to devices with standardized mating components (see Clauses 4.4.6and 4.6). 1.4 Applicable design parameters This Standard applies to devices that a) prevent natural gas vehicles from being fuelled by a dispenser with service pressures higher than the vehicle it was designed for; b) allow natural gas vehicles to be fuelled by a dispenser with service pressures equal to or lower than the vehicle fuel system service pressure; and c) prevent light duty natural gas receptacles from being fuelled by a heavy duty nozzle. 1.5 Exclusions This Standard does not apply to repaired or rebuilt nozzles. 1.6 Pressure references All references to “psi or kPa” throughout this Standard are to be considered gauge pressures unless otherwise specified. 1.7 Units of measure The values given in SI units are the units of record for this Standard. The values given in parentheses are for information and comparison only. 1.8 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user shall satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Compressed natural gas vehicle (NGV) fuelling connection devices

BS ISO 24139-1:2022 石油和天然气工业 管道输送系统用耐腐蚀合金复合弯管及配件 复合弯管

1   Scope This document specifies the technical delivery conditions regarding design, geometric dimensions, materials, manufacturing procedures, inspection methods, non-destructive testing ( NDT ), marking, package and storage for corrosion resistant alloy ( CRA ) clad bends for use in pipeline transportation systems for the petroleum and natural gas industries. This document is applicable to CRA clad bends for use in transportation or process pipelines transporting corrosive media-containing single-phase or multi-phase fluid such as oil, gas and water for the petroleum and natural gas industries. It can also be used as reference in other fields. Two technical delivery conditions classes for clad bends are designated. Class B provides a standard quality level for clad bends and Class S provides technical requirements for sour-service conditions. It is the responsibility of the purchaser to specify the appropriated class, based upon the intended use and design requirements.

Petroleum and natural gas industries. Corrosion resistant alloy clad bends and fittings for pipeline transportation system - Clad bends

SY/T 6826-2022 输油管道泄漏监测系统技术规范

Technical specifications for oil pipeline leakage monitoring systems

SY/T 6151-2022 钢质管道金属损失缺陷评价方法

Evaluation method for metal loss defects in steel pipelines

SY/T 7666-2022 油气管道缺陷修复用B型套筒

Type B sleeve for repairing defects in oil and gas pipelines

SY/T 7664-2022 油气管道站场完整性管理体系 要求

Oil and gas pipeline station integrity management system requirements

SY/T 7027-2022 海洋隔水管系统用钢管

Steel pipes for marine riser systems

ISO 24139-1:2022 石油和天然气工业.管道运输系统用耐腐蚀合金复合弯管和配件.第1部分:复合弯管

This document specifies the technical delivery conditions regarding design, geometric dimensions, materials, manufacturing procedures, inspection methods, non-destructive testing (NDT), marking, package and storage for corrosion resistant alloy (CRA) clad bends for use in pipeline transportation systems for the petroleum and natural gas industries. This document is applicable to CRA clad bends for use in transportation or process pipelines transporting corrosive media-containing single-phase or multi-phase fluid such as oil, gas and water for the petroleum and natural gas industries. It can also be used as reference in other fields. Two technical delivery conditions classes for clad bends are designated. Class B provides a standard quality level for clad bends and Class S provides technical requirements for sour-service conditions. It is the responsibility of the purchaser to specify the appropriated class, based upon the intended use and design requirements.

Petroleum and natural gas industries — Corrosion resistant alloy clad bends and fittings for pipeline transportation system — Part 1: Clad bends

T/CCGA 40012-2022 LNG薄膜罐设计、施工和验收技术规范

本文件规定了陆上LNG薄膜罐设计、施工、检验和验收。 本文件适用于储存液化天然气（LNG）且设计压力不大于50kPa的地上薄膜罐设计、施工和验收。 本文件不适用于地下薄膜罐。地下薄膜罐绝热结构和薄膜内罐施工可参照本文件执行。

Code for design, construction and acceptance of LNG membrane tanks

T/CASMES 120-2022 埋地钢质弯管自动化热缠绕聚乙烯复合带防腐层技术规范

本文件规定了埋地钢质弯管热缠绕聚乙烯复合带防腐层的术语和定义、结构和厚度、材料、防腐层涂敷、质量检验、标识、贮存和运输、补伤、安全、卫生和环境保护、技术文件等。本文件适用于工作温度不超过70℃、管径DN300～DN1600、弯曲半径为5Dmm或6Dmm的埋地钢质弯管自动化热缠绕聚乙烯复合带防腐层的设计、生产、检验以及验收。

Technical specification for anti-corrosion layer of buried steel elbow automatic hot-wound polyethylene composite tape

T/CASEI 014-2022 在役立式圆筒形钢制焊接储罐检验技术规范

本文件规定了在役立式圆筒形钢制焊接储罐检验及其结果评价的基本要求。 本文件适用于设计压力小于0.1MPa,公称容积不小于1000m3,盛装石油、石油产品、石化产品或其他类似介质的在役立式圆筒形钢制焊接储罐检验及其结果评价。公称容积小于1000m3 的同类型储罐可参照执行。

Technical specifications for inspection of in-service vertical cylindrical steel welded storage tanks

CSA/ANSI NGV 4.3-2022 压缩天然气汽车燃料的温度补偿 本文件提供给 SCC 仅供非商业内部使用 为明确起见 不允许进一步复制或分发 转售是

1 Scope 1.1 Inclusions This Standard details the safety and performance requirements for temperature compensation control used to prevent compressed natural gas (CNG) dispensing systems from exceeding a safe fill level for vehicle fuel storage container(s). This Standard contains safety performance requirements for compressed natural gas fuelling dispenser temperature compensation systems. It applies to newly manufactured dispensing systems and the field evaluation of existing dispensing systems designed primarily to allow for full fill and to avoid over-pressurization of vehicle fuel storage containers under the operating temperature conditions as specified in this Standard. This Standard applies to CNG fuelling of vehicle containers with service pressures of a) P30 [20 700 kPa (3000 psi)]; b) P30HD [20 700 kPa (3000 psi)]; c) P36 [24 800 kPa (3600 psi)]; and d) P36HD [24 800 kPa (3600 psi)]. P30HD and P36HD are designations used in accordance with CSA/ANSI NGV 1, and throughout the document, the use of P30 and P36 are also applicable to P30HD and P36HD, respectively (see Annex A of this Standard regarding applicable vehicle service pressures). This Standard is applicable to the dispensing of only natural gas that meets quality and specifications contained in ASTM D8080. 1.2 Pressure references All references to pressure throughout this document are to be considered gauge pressures unless otherwise specified. 1.3 Quality and innovation Nothing in this Standard is to be considered in any way as indicating a measure of quality beyond compliance with the provisions it contains. It is designed to allow compliance of products that may exceed what is specified in the provisions herein. The requirements of this Standard are not intended to constrain innovation. In its preparation, full recognition has been given to possibilities of improvement through ingenuity of design. When considering fuel compositions, controls, materials, designs, or constructions not specifically dealt with in this Standard, these alternatives are to be evaluated as to their ability to yield levels of safety and performance equivalent to or better than those prescribed by this Standard. Note: This Standard is subject to revision as further experience and investigation show it is necessary and desirable. 1.4 Precedence Users of this Standard are advised that the devices, products, and activities within its scope might be subject to regulation at the federal, state, provincial, or local levels. Users are strongly urged to investigate this possibility through appropriate channels. In the case of a conflict between this Standard and federal, provincial, state, or local regulations, the governmental requirements take precedence. 1.5 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.6 Units of measurement All dimensions used in this Standard are in SI units, unless otherwise specified. If a value for a measurement, as given in this Standard, is followed by an equivalent value in other units, the first stated value is to be regarded as the specification. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, either the first stated unit, or both, are to be provided.

Temperature compensation for compressed natural gas vehicle fuelling This document is provided to SCC for non-commercial, internal use only. For greater clarity, no further reproduction or distribution is permitted. Resale is

KS B ISO 16961-2022 石油、石化和天然气工业 钢制储罐的内涂层和衬里

Petroleum, Petrochemical and natural gas industries - Internal coating and lining of steel storage tanks