81.100 玻璃和陶瓷生产设备 标准查询与下载

KS L 0008-2012 烧陶瓷、耐火物用隧道窑热平衡测定与计算方法

이 표준은 도자기, 내화물 등의 소성용 터널 가마 중, 액체 연료 또는 기체 연료로 사용할

Calculation method of heat balance of the firing tunnel kiln for potteries and refractories

KS L 0008-2012(2022) 陶瓷和耐火材料隧道窑热平衡计算方法

Calculation method of heat balance of the firing tunnel kiln for potteries and refractories

KS L 0007-2012(2017) 耐火陶瓷周期窑热平衡计算方法

Calculation method of heat balance of the firing periodic kiln for potteries and refractories

KS L 0007-2012 烧陶瓷、耐火物用间歇窑热平衡测定与计算方法

이 표준은 도자기, 내화물 등의 소성용 단독 가마 중, 액체 연료(중유) 또는 기체 연료를

Calculation method of heat balance of the firing periodic kiln for potteries and refractories

GSO EN 13042-3:2011 用于制造、处理和搬运中空玻璃的设备和工厂 安全要求 第3部分：单节 (IS) 机器

1.1 This European Standard applies to the design and installation of IS machines including the gob distributor and machine conveyor. 1.2 ! This European Standard deals with the significant hazards, hazardous situations and events relevant to IS machines, when they are used as intended and under the conditions of misuse which are reasonably foresee-able by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from significant hazards during commissioning, operation and maintenance." 1.3 This European Standard does not deal with gob feeders (see EN 13042-1) and handling machines for feed-ing (see EN 13042-2) which are self-standing machines used for the delivery of portions of melted glass to hollow-glass-forming machines such as glass presses (see EN 13042-5). 1.4 This European Standard is not applicable to IS machines which are manufactured before the date of publication of this European Standard by CEN.

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 3: IS Machines

GSO EN 13102:2011 陶瓷设备 安全 装卸软粘土砖

This European Standard applies to: - machines for stacking or dehacking fired or unfired fine clay wall tiles and floor tiles on/from fixed or movable supports (see Figure A.1); - machines for loading or unloading fired or unfired fine clay wall tiles and floor tiles into/from containers (see Figures A.2 and A.4); - machines for loading or unloading fired or unfired fine clay wall tiles and floor tiles on/from stackable frames (see Figure A.3). 1.2 This European Standard deals with the significant hazards, hazardous situations and events relevant to ceramic machines for loading and unloading of fine clay tiles, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard does not deal with noise. This standard deals with the preventive measures to minimise these hazards arising from the commissioning, the operation and maintenance. 1.3 The interface with the transport system for stacks, containers is covered by this European Standard for some examples not for all possibilities (see e.g. 5.6.4, 5.6.7). 1.4 This European Standard is not applicable to: - machines for setting and dehacking of split tiles and roof tiles; - auxiliary machinery such as vacuum generators. 1.5 This European Standard is not applicable to machines, which are manufactured before the date of publication of this European Standard by CEN.

Ceramic machines - Safety - Loading and unloading of fine clay tiles

GSO EN 13367:2011 陶瓷机械 安全 运输平台和机车

This European Standard applies for the design, installation and commissioning of transfer platforms and cars and ancillary devices for the process related transport of ceramic material on rails. The rails, which are considered to be horizontal and the movement of vehicles in equipment and machinery connected with the process related transport such as kilns, dryers, collector scaffolds, machinery for loading and unloading are also covered. 1.2 This European Standard deals with all significant hazards, hazardous situations and events relevant to transfer platforms and cars, when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). Noise is not a significant hazard. This document deals with the preventive measures to minimise these hazards which can arise during commissioning, the operation and maintenance. 1.3 This European Standard is not applicable to: 1.3.1 Kilns and dryers (see EN 746-1:1997), machinery for setting and dehacking of heavy clay and refractory, products and machinery for loading and unloading of fine clay tiles; 1.3.2 Retrial, packaging and storage of finished products; 1.3.3 Transport of cars with not rail mounted equipment e.g. with driverless trucks (see EN 1525:1997); 1.3.4 Transfer platforms and cars which are driven by human power. 1.4 This European Standard is not applicable to transfer platforms and cars and ancillary devices which are manufactured before the date of publication of this European Standard by CEN.

Ceramic machines - Safety - Transfer platforms and cars

GSO EN 13035-7:2011 平板玻璃制造、搬运和搬运设备和工厂 安全要求 第7部分：夹层玻璃切割机

1.1 This European Standard applies for cutting machines for laminated glass including the following steps: transport and positioning, synchronous cutting (scoring) from both sides, break-out, electrical heating and separation. 1.2 This European Standard deals with the significant hazards, hazardous situations and events relevant to cutting machines for laminated glass when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). Those hazards, which are dealt with in the ad-hoc standard EN 619 for conveyors are excepted. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. Hazards from noise are not considered to be significant. 1.3 This European Standard is not applicable to cutting (scoring) and break-out of monolithic glass (see EN 13035-3 and EN 13035-6). 1.4 This European Standard is not applicable to the cutting of laminated glass by sawing or by the use of high-pressure liquid. 1.5 This European Standard is not applicable to the significant hazards of conveyors and machines for the manufacture, treatment and processing of flat glass such as tilting tables. 1.6 This European Standard is not applicable to cutting machines for laminated glass which are manufactured before the date of publication of this European Standard by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass

GSO EN 13035-5:2011 平板玻璃制造、搬运和装卸设备及工厂 安全要求 第5部分：堆垛和卸垛机器及装置

This European Standard applies for machines and installations for stacking and de-stacking that are specifically de-signed for building-up or taking down upright stacks of flat glass sheet by sheet including unloading and loading of single sheets of flat glass from or onto machines or transport devices (conveyors). NOTE For sketches with examples of typical constructions, see Annex A (informative), Figures A.1 to A.9. 1.2 This European Standard deals with the significant hazards, hazardous situations and events relevant to machines and installations for stacking and de-stacking flat glass when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). Those hazards which are dealt with in the ad-hoc standard EN 619 for conveyors are excepted. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. 1.3 This European Standard is not applicable to the significant hazards of conveyors and other machines for the manufacture, treatment and processing of flat glass, e.g. tilting tables, equipment for storage of flat glass, such as stillages. If there are specific hazards which arise by the co-operation of this machinery and equipment with machines and installations for stacking and de-stacking, appropriate measures are specified. 1.4 This European Standard is not applicable to building up or taking down stacks by means of cranes that are temporarily equipped via hook with load-lifting attachments with suction cups to lift flat glass. 1.5 When compiling this European Standard, it was assumed that lifting movements are only used as part of full automatic machines and that the related hazards are not significant.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 5: Machines and installations for stacking and de-stacking

GSO EN 13035-9:2011 制造、加工和处理平板玻璃的设备和设备 安全要求 第9部分：清洗装置

This European Standard contains the safety requirements for the design and installation of stationary glass washing installations as shown as typical in Annex A. Glass washing installations are designed to perform the following functions: feeding of flat glass to the cleaning and drying unit and transport (delivery) to the estimation equipment and to the take-off position of the flat glass sheet. None of the processing phases requires direct manual intervention. 1.2 !This European Standard deals with the significant hazards, hazardous situations and events with the exception of those by interfaces with other machines used in a process line relevant to glass washing installa-tions, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4)." This European Standard specifies the appropriate technical measures to eliminate or reduce risks which can arise from these significant hazards during commissioning, the operation and maintenance. ! Safety requirements and/or protective measures are given in Clause 5. When references are made to B level standards such as EN 953, EN 1037, EN 1088, EN 60204-1, EN ISO 13850 and EN ISO 13857, the manufacturer should carry out an adequate risk assessment for the requirements thereof where choice is necessary." 1.3 This European Standard is not applicable to machines for loading and unloading of glass (see EN 13035-5) and to conveyors (see EN 619) and fans. If there are specific risks that arise by their use as an integral part of flat glass washing installations, appropriate measures are specified. 1.4 This European Standard is not applicable to glass washing installations for automotive and bent glass. 1.5 This European Standard is not applicable to water preparation and disposal of waste washing liquid. 1.6 This European Standard is not applicable to machinery manufactured before the date of publication of this European Standard by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 9: Washing installations

GSO EN 13035-2:2011 平板玻璃制造、装卸和装卸设备和工厂 安全要求 第2部分：工厂外储存、装卸和运输设备

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage (as defined in 3.2.1), handling (as defined in 3.2.2) and transportation (as defined in 3.2.3) of flat glass outside the factory (as defined in 3.1.1) and including stillages, pallets, frails fixed to vehicles, in-loader vehicles, specific glass-securing devices, stanchions and vacuum-lifting devices which are used for road transport and on building sites. 1.2 Specific hazards due to the use inside the factory are dealt with in EN 13035-1. 1.3 This standard deals only with the devices which are directly in contact with the glass. This standard does not apply to manual handling equipment such as carrying straps and vacuum pads. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass. This European Standard does not apply to equipment for the transport by other ways than on road e.g. by ship or train, and the transportation of glazed windows/frames. 1.4 This standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard. 1.5 This document is not applicable to storage, handling or transportation equipment for flat glass outside the factory, which is manufactured before the date of its publication as EN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 2: Storage, handling and transportation equipment outside the factory

GSO EN 13042-2:2011 平板玻璃制造、加工和加工设备和工厂 安全要求 第2部分：进料中使用的处理装置

This document contains the requirements for safety for the design and installation of stationary handling machines for feeding from the taking up of a post of melted glass out of the working bowl of a glass melting furnace through transport to delivery to a glass blower or to a forming machine for hollow glass. 1.2 This European Standard deals with all significant hazards, hazardous situations and events relevant to handling machines for feeding, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from significant hazards during commissioning, operation and maintenance. 1.3 This European Standard does not deal with feeding with shears alone, with the transport of the melted glass post by its own weight in free fall or by trueing (gob feeder, see EN 13042-1). 1.4 This document is not applicable to handling machines for feeding which are manufactured before the date of publication of this document by CEN.

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 2: Handling machines for feeding

GSO EN 13042-1:2011 用于制造、处理和加工中空玻璃的机器和设备 安全要求 第1部分：料滴给料机

1.1 This European Standard applies to the design and installation of gob feeders which provide hollow glass forming machines with gobs. 1.2 This European Standard deals with the significant hazards, hazardous situations and events relevant to gob feeders, when they are used as intended and under the conditions foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks which can arise from these significant hazards during commissioning, operation and maintenance. 1.3 This European Standard does not deal with bowl firing. 1.4 This European Standard is not applicable to gob feeders which are manufactured before the date of publication of this European Standard by CEN.

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 1: Gob feeder

GSO EN 13035-3:2011 平板玻璃制造、搬运和搬运设备和工厂 安全要求 第3部分：切割机

This standard contains the requirements for safety for the design and installation of machines with one movable bridge for cutting of flat glass, which operate by scoring of the glass placed on a horizontal support. This standard covers the transport of the glass on the machine. 1.2 This European Standard deals with all significant hazards, hazardous situations and events relevant to flat glass cutting machines, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. Hazards from noise are not considered to be significant. 1.3 This standard does not apply to flat glass cutting by abrasive cutting or by the use of high pressure liquid or lasers. 1.4 This standard does not apply to loading and unloading of flat glass on to or from cutting machines and the breaking out (see EN 13035-5 and EN 13035-6). 1.5 This standard does not apply to conveyors (see EN 619) and fans as used as integral parts of the machinery. If there are specific risks that arise in connection with flat glass cutting machines, appropriate measures are specified. 1.6 This standard does not apply to cutting of laminated glass (see EN 13035-7). 1.7 This standard does not apply to cutting while the glass is moving. 1.8 This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 3: Cutting machines

GSO EN 13035-1:2011 平板玻璃制造、装卸和装卸设备和工厂 安全要求 第1部分：工厂内的储存、装卸和运输设备

1.1 This standard contains the requirements for safety for the design and installation of equipment intended for the storage, handling and transportation of flat glass inside the factory as described in Clause 3. It applies to stationary, movable and mobile storage equipment (see 3.2), mechanical and automatic handling equipment (see 3.3) and transportation equipment (see 3.4) (see overview in Annex A). 1.2 Additional requirements for dealing with specific hazards due to the use outside the factory are dealt with in prEN 13035-2. 1.3 This standard only deals with the devices which are directly in contact with the glass. Tractors, cranes, hoists and fork lifts are out of the scope as well as parts of other powered vehicles that are not in contact with the glass (see 3.4.1). This standard does not apply to manual handling equipment as defined in 3.3.1. 1.4 This standard deals with all significant hazards, hazardous situations and events relevant to equipment for the storage, handling and transportation of flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, the operation and maintenance. Noise has not been considered to be a significant hazard for any type of equipment in the scope of this standard. 1.5 This document is not applicable to storage, handling or transportation equipment for flat glass inside the factory, which is manufactured before the date of its publication as EN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory

GSO EN 13035-4:2011 平板玻璃制造、加工和加工设备及工厂 安全要求 第4部分：倾斜平台

This standard contains the requirements for safety for the design and installation of tilting tables, where the flat glass is brought from the horizontal almost to the vertical position or vice versa by lying on or supported at the lower edge leaning against a supporting surface. 1.2 This standard deals with all significant hazards, hazardous situations and events relevant to tilting tables for flat glass, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. Noise is not a significant hazard for this type of machines. 1.3 This standard is not applicable to tilting tables where all movements are done by human power. 1.4 This standard is not applicable to additional equipment, e.g. for cutting (see EN 13035-3), loading and unloading (see EN 13035-5), break-out (see EN 13035-6), transporting (see EN 619) of flat glass as used as integral parts of the machinery. If there are specific risks that arise in connection with tilting tables, appropriate measures are specified. 1.5 This document is not applicable to tilting tables which are manufactured before the date of publication of this document by CEN.

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 4: Tilting tables

QB/T 4171-2011 行列式制瓶机

本标准规定了行列式制瓶机的分类、规格系列、要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于玻璃瓶罐工业自动成型各种小口瓶和大口瓶的行列式制瓶机系列产品。

Individual section forming machine

LST EN 13035-9-2006+A1-2010 制造、处理和加工平板玻璃的机器和设备 安全要求 第9部分：清洗装置

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 9: Washing installations

LST EN 13035-3-2003+A1-2009/AC-2010 平板玻璃制造、处理和加工的机器和设备 安全要求 第3部分：切割机

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 3: Cutting machines

LST EN 13035-11-2006+A1-2010 平板玻璃制造、处理和加工的机器和设备-安全要求-第11部分：钻孔机

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 11: Drilling machines